Accent LC (2000-05) :: 2002 - Manual Trans Has Small Leak At Slave Cylinder For Clutch
So my accent with a manual trans has a small leak at the slave cylinder for the clutch. I am driving home and it's shifting hard. I get home pull up to where I live and push In the clutch and the car feels like the clutch is not pushed in. RPMs drop and car stalled. Look under hood and see not fluid in clutch master cylinder. Fill with fluid and pump pedal. I get some pedal back but the car will not crank. Nothing. I have accidentally cranked car when in gear in the past and there did not seem to be a safety switch as the car would move if my foot was not on brakes.
View 4 RepliesThunderbird :: Slave Or Master Cylinder In Clutch System Bleeding Air Out
I'm having trouble bleeding the air out of my slave cylinder or master cylinder in my clutch system. I've been trying for a couple days now is there a trick to this?
View 7 RepliesGolf IV / Jetta IV :: Clutch Fork Won't Move So That The Slave Cylinder Can Slide In
So I took my tranny off to fix a broken dog bone mount bolt problem. I am now in the process of putting it back on. I raised the tranny bolted all the bolts on had everything almost back together and I went to put my slave cylinder in and the clutch fork won't move so that the slave cylinder can slide in. Did I maybe put the clutch fork in wrong? pretty positive I put it back in as it was and slide the clip through the hole and everything.
View 11 RepliesFord Ranger / B-Series :: 1994 - Slave Cylinder Went Out / Clutch Replacement
1994 Ranger 4.0 XLT 4X4. My slave cylinder went out so I thought I would put in a spec clutch in while I'm in there. What do I have to pull off to get the 5 speed tranny / transfer case down? I don't want to pull off what I don't have to but I don't want to make it hard either. No Chilton on hand and I did a search on clutch but found no thread for replacement.
View 2 RepliesMitsubishi - Lancer :: 2004 - Unable To Bleed Clutch After New Slave Cylinder Installed?
Replaced a bad clutch on a 2004 Mitsubishi Lancer. I have been unable to bleed the slave cylinder after replacing both it and the master cylinder. I suspect either the slave cylinder is bad, or I put the incorrect throwout bearing in when the clutch was replaced. The slave cylinder is located inside of the bell housing
View 5 RepliesFord Ranger / B-Series :: 2001 - Bled Slave Cylinder Now No Clutch Pressure?
Dad has a 2001 well cared for Mazda B3000 with around 128,000 miles on it. Motor runs fine, so did the tranny up until a couple of weeks ago. The tranny needs a new clutch, throw out bearing, and pressure plate. It was drivable up until about four days ago.
My Dad has been working 6-7 days a week and hasn't had time to tear into the tranny. We just drained the old fluid out and put in new when it first started making the noise it makes. We have priced the parts and was just waiting for my Dad to get a weekend off to tackle the problem. But someone at work told my Dad to bleed the slave cylinder before he tore into the tranny, just to see if it would work.
Well we bled the slave cylinder just like you do brakes. But now the clutch has no pressure, it just goes to the floor. We have tried everything. My dad uses the truck to commute back and forth to work. So, I am looking for any tricks on how we can get pressure back in the clutch so he can get to work.
Ford Ranger / B-Series :: 1987 - Clutch Slave Cylinder Not Functioning Correctly
Can contaminated or old fluid make the clutch slave cylinder not function correctly? Mine won't completely disengage the clutch after sitting for several hours or if its really cold outside. The master is new and has been bled but now the fluid looks black.
View 1 RepliesFord F-150 - 1997-2003 :: New Clutch Kit - Hydraulic Line Will Not Connect Into Slave Cylinder
I put a new clutch kit in my 99 f-150 with the 4.6. It came with the clutch disk,pressure plate and throw out bearing. I got the tranny back up in but now my Hydraulic line will not connect into the slave cylinder. Its still the same one that was in it.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Doing Clutch - Slave Cylinder Removal
I'm getting ready to swap my clutch and got to looking at the slave cylinder. I read somewhere that you have to rotate and twist it to get it out? Or something else? Also after reinstalling how do you get the slave plastic piece cut that holds the rod in? Or do you just push the clutch?
View 4 RepliesGolf IV / Jetta IV :: Slave Cylinder Green Rubber Boot Filled With Brake Fluid And Began Leaking A Little
Was bleeding my brakes and clutch. Using a power bleeder and it seems as though I put a little too much pressure into the system. The Slave cylinder's green rubber boot filled with brake fluid and began leaking a little. Did I blow a seal? Is this normal with pressure like that? I feel like pushing the clutch in would give more pressure than my little hand pump gives...
View 2 RepliesFord Transmission :: T18 Will Not Shift - Slave Cylinder Is Leaking A Little Bit
My T18 tranny in my 85 F150 will not shift, first instinct was clutch but after tearing the drivetrain out of the truck to check the clutch, there is virtually no wear on it. Slave cylinder is leaking a little bit but the mechanic that took a quick look at it said it was still working. She was shifting fine when i left for school, then when i got off the highway i couldn't shift.
View 1 RepliesCamry :: 2003 - Transmission Fluid Leaking After Replacing CV Axle And Seal?
I have replaced my cv axle and seal, and now I have transmission fluid leaking from the axle seal. What could be the cause of this? The seal is brand new as is the cv axle. Could it be that it the seal isn't seated correctly? What could possibly went wrong to cause this?
View 3 RepliesPassat (B5) :: Leaking Brake Fluid - Clutch Pedal (manual) Does Not Return All The Way
Over the past week I have noticed leaking brake fluid and after my STOP Brake failure light came on I topped off the brake fluid and it is down to a low level again. I also notice that the clutch pedal (manual) does not return all the way when the brake fluid is low and I assume they share the same fluid. I'm going to take it to my mechanic but could this be a clutch problem or just a fluid leak.
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 - Replacing Clutch Master Cylinder
I am looking for a how to vid or resource on doing the job right. I purchased the complete replacement master cylinder from Napa. 2002 7.3 Powerstroke
View 3 RepliesEscort :: 95 Manual Transmission / Clutch Never Slipped
95 Ford Escort 1.9L, 330,000 miles. Never changed the clutch and i bought it with 80k on it. With that said the clutch never slipped and a lot of this is highway mileage so i never saw a reason to change the clutch just because.
Last week i pulled into the driveway i depressed the clutch pedal as i normally do and as i slowed, the car bucked like it was still in gear and didn't recognize the clutch was depressed. When it started bucking i tried to pull the gear shifter to neutral but it wouldn't move, the car finally died in it's parking spot. I quickly popped the hood and had my son press the clutch in and out and all components seemed to be moving fine, i was mainly looking at the slave cylinder assuming since it's a hydraulic clutch if it was a hydraulic issue that wouldn't move if i didn't have hydraulic pressure.
No obvious leaks were noted, i looked at the master cylinder and it seemed a little low but not empty maybe just above min. I filled it to max and still no change. So i assumed it was the clutch finally disintegrated and locked up. Yesterday i got in the car to attempt to move it to the garage to work on it. It started up fine, shifted through all gears with no issue's, drove it around for about 15minutes shifting a lot and pressing the clutch randomly and it worked fine.
I brought it back home and tried to kill it a few more times before i got it to the garage, it finally locked again but it was in neutral and i couldn't get into any gear. Turned the car off and then restarted and it shifted into gear, i pulled it into the garage and stopped with no other issue's.
Checked closer for leaks, between master and slave and couldn't find any. Pulled speedo cable and checked trans fluid, its brownish red (more brownish) and thin but didn't really smell burnt and it is at the correct level. Linkage has some slop in it but i don't see it binding anywhere, i layed under the car and was able to move linkage in/out of gear with my hand. It's easy enough to say the clutch is well over due for changing but since there were no signs of a failing clutch when i drove it i think i need to look elsewhere.
Could it be worn fluid? Could it be debris in the line? Or could it be that the fork just isn't engaging or disengaging properly due to wear?
Toyota - Matrix :: 5 Speed Manual Transmission - Type Of Fluid To Use
I have a 2006 Toyota Matrix. I want to change my manual transmission fluid in it. I have called dealerships and auto parts stores and keep getting different answers. I was wondering exactly what kind of fluid do I use and how much fluid do I use. I am not going to pay $219 for the dealership to do it but I want to make sure I put in the right kind and the right amount.
View 1 RepliesGolf IV / Jetta IV :: Manual Transmission Fluid Change On Older MK4?
So I recently bought my 03 VW Golf TDI, and have it in the shop this morning to get the wheel alignment done, balance my winters, fuel/cabin filter changed, as well as an oil change. I am now wondering whether or not to give them a call to change the transmission oil as well...
But.. the vehicle has alot of km's on it (358K) and I keep reading that it would do more harm then good? Is this true? Doesn't make any sense to me, but the car could shift more smoothly I think if I do it, and I have yet to see any tran fluid change in the previous owners records in quite some time..
Ford - Focus :: 2002 - Changing Manual Transmission Fluid?
I've owned a manual 2002 Ford Focus ZX5 for 5 years. I bought it with 77,000 miles and it now has 112,400. I've been pretty good at having the oil changes and tune-ups at the right mileage. This last time I took it to a new service place, they suggested I looked into changing the Manual Transmission Fluid. I have never had it done, and I'm not really sure about the previous owner. What's your take on this? I've done some research and opinions seem to differ quite a bit about at what mileage the transmission fluid should be changed.
View 10 RepliesHonda - Accord :: 2013 - Manual Transmission / Clutch Completely Gone
I have 2013 Honda Accord 6 sp manual with 25k miles on, its clutch was completed gone last week, got new replacement, local Honda customer rep. told me I should watch my driving pattern, should using more break, instead transmission slow down, particular from high speed/high gears. I told them, we have 2008 Civic 5 speed Manual, I taught my two daughters how to drive it, and the car is still running without any problem… And, this is manual transmission car, tell a driver can not using/changing gears slowing down car is a joke… but maybe I am wrong...
Is there a possibility Accord has design problem with inferior clutch materials used on their new 6 speeds manual Accord? Since car has new clutch, should I keep it for a while? Or, sale it immediately? I just can’t not see I am going to come up another 3rd replacement on clutch before the car get into 60K miles.