Camry :: 2007 - Code P0606 / ECM Is Bad On The Car?
My friend has a 07 Camry 4cyl and has code P0606, Engine control module/Powertrain control module processor. The car runs and drives good. My friend recently got the piston rings replaced about a month ago for the recall, and he told me the service light was not on when he dropped off the vehicle. After he got it back it wasn't on and just came on a few days ago. Hard to believe the ECM is bad on the car, I'm thinking it was something with the removal and install of the engine causing P0606. Does it need to be reflashed?
View 1 RepliesCamry :: P0606 Code - PCM / ECU Fault
So I had a P0606 code which points to a PCM/ECU fault. It would come and go and not really cause much of a problem with driving. It did stall once but it started right back up. The light would come on for half a day and go off. Rinse and repeat......
The dealer replaced it today under my extended warranty. Sure enough, the CEL returned today. I haven't had the code read but I can only assume it will be P0606 again.
Camry :: 2005 - Check Engine Light Is On / Code P0138 (Rear O2 Sensor)
My 2005 Camry check engine light is on. The trouble code is P0138, bank 1 sensor 2 oxygen sensor. Engine is the 2AF-ZE. Not a California emission car. Car is Japan built. It has two O2 sensors. What is the correct OEM part #? I believe it would be a Denso?
View 2 RepliesCamry :: White Smoke Coming From Exhaust On Startup After Replacing PCV Valve
2009 Camry 4cyl
I changed my PCV valve over a month ago and still have white smoke coming form exhaust on startup. The smoke goes aways as always, after that the smell is gone and the car runs like normal. The smell of the smoke is not really sweet as if it was coolant leaking, but its not exactly smelling like burnt oil either (I've had cars that burnt oil real bad and it smelled different than this camry).
I've been keeping an eye out on my oil and coolant levels, both seem to be ok. I refilled my coolant tank to full about 2.5 months ago as it was very low and its still almost at full right now. My oil after about 4k miles on the dipstick measures right in the middle of the min and max dots, which it has been for as long as I've owned the car. So these levels are ok I think.
Now, I've read somewhere a while back that after changing the PCV valve or rather after taking the old one off that there still will be some residue to be burnt off. A way to get rid of that is to create a makeshift vacuum by plugging one end of the hose (the one that attaches to PCV valve) and leaving the PCV valve off while running the engine, putting some kind of cloth or similar over where the PCV valve should go to collect all the burnt stuff, thus cleaning the remainder out. Is it possible that this might be the a solution?
Golf IV R32 :: Fault Code P0606 - Powertrain / Engine Control Module?
The code the R threw was p0606 which is the Powertrain/ Engine control module? Where these components are in my R? Or how I can go about trouble shooting this problem?
View 9 RepliesCamry :: P0138 And P2195 - Location Of Sensors
I plan on changing the 2 sensors from the codes p0138 (bank 1, sensor2) and p2195 (bank 1, sensor 1). Any visual picture on here to locate these sensors?
2007 Xamry XLE V6
Jeep - Grandcherokee :: 1998 - P0138 Code / O2 Sensor High Voltage
I drive a 1998 Jeep Grand Cherokee, 6 cylinder engine, with about 120,000 miles on it. I used a code scanner and pulled a P0138 code-bank 1 sensor 2 O2 sensor high voltage, if I'm correct. First of all, it looks like this sensor is after the catalytic converter, right? So I think I either have a bad 02 sensor or a bad catalytic converter. What are the consequences of driving around without fixing this? Will I see any reduction in fuel economy, or any potential long-term problems elsewhere?
View 2 RepliesCamry :: CEL On With P0606 - PCM Processor Fault / P0157 - O2 Sensor Circuit Low Voltage
2 weeks ago a check engine light came on with P0351-Ignition Coil "A" Primary/Secondary Circuit Malfunction, took the car to Toyota dealer and replaced ignition coil for cylinder No1. I drove the car for about 10K and check engine light came on again with P0606-PCM Processor Fault.
For the past week I was monitoring the DTC's using INNOVA- CanOBD2 Code Reader 3030 (ordered ODB2 USB tool to check live data on a laptop, on it's way...). I had P0606 on all the time, about everyday. For 3 times I had P0157-O2 Sensor Circuit Low Voltage (Bank #2 Sensor #2) on.
What's the link between the two DTC's? Why not P0157 alone? Or P0606 alone? What is the procedure to diagnose this?
Ford 6.0L Power Stroke Diesel :: 2007 F350 Battery Died / DTC P0606
My 2007 F350 6.0l DRW LARIAT battery voltage was too low to restart her while out and about today. I did notice that she seemed kind of when I started her up leaving my town to got over two towns away. So i set my Scan Gauge to check voltage and it was low considering she was running, in the low 12V range with radio and a/c running. So I figured the regulator is on it's way out but I this be able to restart her up. Anyway after a jump she started right up and I was able to get home no issues. After I jump started her the check engine icon was illuminated with DTC P0606. I'm not 100% on why this trouble code was recorded other than the fact that I tried to start her up which caused battery to fall below the 9.6V threshold to power the PCM. The voltage was still low after jumping her, so I figured i better swap in a new alternator but what kind. I hear that the alternator is an issue with this truck, so what should I get?? What alternator is proven to last on these trucks?
View 14 RepliesFord Exhaust System :: 1994 F250 - Replacing Exhaust?
I have been thinking about toying with my exhaust. I don't have a crazy amount of money. I got a 94 F250 with the 5.8 liter 351. Heres what I was thinking. Get rid of everything after the cat, and then run a single 3 inch pipe from the cat to a flowmaster 40 series, and then exit either right before the back tire or right after it.
View 7 RepliesFord Exhaust :: 2008 F250 - Replacing Exhaust Manifolds
replacing exhaust manifolds on my 2008 f250 super duty got a broken stud on right front top tried to drill it out but there's no room somebody said to weld a nut to the broken stud but if I do this will the weld mess up the aluminum head.
View 1 RepliesCamry :: 2008 Toyota CE - P0101 Code After Replacing Spark Plugs
This past Sunday, I replaced the spark plugs on my 2008 Toyota Camry CE, following one of the sticky DIYs. My car has approximately 107,xxx miles.
Last night on my drive home from work my CEL came on. First time seeing a CEL light since my BMW days, . Luckily, I have a OBDII scanner at home and after running the scanner, it gave me the following trouble codes:
- P0101
- P0172
I went ahead cleaned the air filter (I have an Injen SRI installed).
After doing some research on the interwebs, I have concluded that this code has to do with the MAF. Time permitting, I am going to clean the MAF sensor later tonight. In the meantime I reset the CEL, to see if it will come on again.
My only question, which I am unable to find an answer to, is:
Can there be a possibility that the P0101 and P0172 trouble codes be related to me replacing the spark plugs, or is this just a mere coincidence?
Camry :: 2007 - Replacing Broken Air Intake Box?
On a 2007 Camry CE i4. My air intake box broke, either age or the mechanics that worked on my car broke it. And ones on ebay cost 100+ dollars. Either a customer cai will be cheaper, or the junk yard. I know a cai does nothing but changes the sound of your car.
View 2 RepliesCamry :: 2007 LE - Replacing Indicator Light Bulb In AC Controls?
The little mark on the control knob to select air flow is unlit at night with the headlights on in my 2007 Camry LE. Apparently there is a bulb in there somewhere which needs to be replaced. How to change that bulb and get an indicator at night so that I can position the knob in the correct position?
View 1 RepliesCamry :: 2007 - Power Steering Hard To Turn After Replacing High Pressure Hose
I have an 07 Camry with a hard to turn steering wheel. I had to replace the high pressure hose from the rack due to a leak. After that I basically bled the system as one would do under normal circumstances. With the cars front wheels off the ground I turned the wheel hard left and right. The wheel did give a bit but not to the point of perfection. After many turns I put the vehicle on the ground and repeated the process. The fluid no longer leaked but the stiffness was still there.
The hose was replaced at 110,000 miles. It's currently at 112,000 miles
Toyota - Camry :: 1996 - Code PO401 / Insufficient Exhaust Flow
1996 Toyota camry le 4 cylinders has code po401 does it damage engine what will it do. Insufficient exhaust flow...
View 3 RepliesCamry :: 2007 LE - Exhaust Buzzing When Accelerating
I have a 2007 Camry le 4 cylinder. When under a load on the highway there is an occasional buzzing that occurs when accelerating (sounds like a piece of metal vibrating at a high pitch). It only happens under about 3000 RPMs and the noise doesn't occur any other time (idle, reving the engine while idle, slow speeds, etc.). Today I got it up on a lift and checked all of the heat shields under the hood and around the exhaust under the car. Nothing seemed loose. I had two mechanics look at it and one thinks that the exhaust flex pipe is the culprit, while the other insists that this is a known issue with the resonator (said a small piece may have broken off of a baffle inside and is vibrating). Are either of these components well known to cause this type of issue? I'd rather not replace both if one is frequently the cause.
View 2 RepliesNoises :: 2007 Camry LE Exhaust Buzzing When Accelerating
I have a 2007 Camry le 4 cylinder. When under a load on the highway there is an occasional buzzing that occurs when accelerating (sounds like a piece of metal vibrating at a high pitch). It only happens under about 3000 RPMs and the noise doesn't occur any other time (idle, reving the engine while idle, slow speeds, etc.). Today I got it up on a lift and checked all of the heat shields under the hood and around the exhaust under the car. Nothing seemed loose. I had two mechanics look at it and one thinks that the exhaust flex pipe is the culprit, while the other insists that this is a known issue with the resonator (said a small piece may have broken off of a baffle inside and is vibrating). Are either of these components well known to cause this type of issue? I'd rather not replace both if one is frequently the cause.
View 3 RepliesCamry :: 2007 - Single To Dual Exhaust Conversion
I would like to retrofit the Lexus LS exhaust tips on my 2007 4 cylinder SE 4 Cyl, only if dual exhaust conversion doesn't have any adverse effects on my car.
Idk much about piping and exhaust systems. Where would the second pipe split from, after or before cat? what pipe diameter? Should the pipe diameter for both exhausts be smaller? Will it affect my hp/torque? Would it be louder or quieter? Any other forseeable effects?