Accent MC (2006-11) :: 2008 - Running Really Bad / Cylinder 1 Misfire
This morning my son started the 2008 Accent and it ran really bad, he shut if off started it again and still ran really bad and check engine light started to flash. Shut it off and ran for the bus to school.
Went and picked up a OBD scanner and found a cylinder 1 misfire. Tried to start it and had a really hard time and when it did start ran like crap and smelled gas. Checked the codes again and now got Multiple cylinder misfires, cylinder 4 misfire and cylinder 1 misfire.
Pulled the engine cover to pull the coils and plugs and I find a ton of mouse crap. No signs of any chewed wires or anything that I could see. Drove it to the local Hyundai dealer tonight because I am worried that it may not be the coil packs. Drove OK to the dealer. My brother is the service manager at the local Mazda dealer and he sees a lot of mouse damage. Said I should put a couple of old socks with moth balls in the engine compartment to deter the mice.
Accent LC (2000-05) :: Intermittent Misfire / Running Rough
I have a 2000 LC that has a few symptoms - intermittent misfire/running rough at these times it has:
dark smoke
uses 3 times the fuel
loss of power (to normal)
will pick up revs slow without running rough and runs normal at high revs.
dies misses and then picks up revs slowly when accelerator is pushed fast to the floor from idle.
Hyundai mechanics checked computer and it coded change spark plug leads this did not fix the problem, and have no idea.
About 6 months ago the car was doing the intermittent thing when it died and liquid was heard splashing on the ground. I found the main petrol line connecting to the pump had come completely off. After replacing all problems ceased and the car ran perfect with full power etc.
I've checked the fuel lines none appear to be leaking etc.
Accent MC (2006-11) :: Rough Idle But Fine When Air Conditioner Off?
I've had my 2010 Accent for about 9 months. It's got about 63K miles on it. Serviced regularly, no issues there. Yesterday while coming home from a road trip....6 hours there, heavy driving while in town, 6 hours back 2 days later, the check engine light came on the dash. I then noticed that the car was idling very rough. When I put it in gear after starting, I can visibly see the car the shake. Having major problems accelerating, I have to mash the gas to the floor to make it go. Shutting off the air conditioner seems to work a bit, but not totally.
I should note that I live in the South East US, it was over 95 degrees when we left town and the destination was over 100 the entire time we were there. I was told this could be vapor lock, but am not sure about what to do to clear that when the temps won't drop around here for some time. I took it to AutoZone this morning to have them read the codes on the check engine light and was told that their code reader was incompatible with my car.
Ford Ranger / B-Series :: 2006 - Running Fine Then Cuts Off?
I have a 2006 2.3 ranger motor runs fine at idle and as I ride down the road the motor just cuts off. If I pump gas it will take off again and in 3 miles it will do it again. After 20 miles running good it will cut off again. Replaced coil pack, fuel pump, Cam sensor, Idle control sensor! What else could be causing this?
View 3 RepliesAccent LC (2000-05) :: 2001 - Car Dies / Stalls If Fill Petrol Tank To Top
Hyundai Accent 2001. Not long after I bought it (from a cowboy, obviously) I filled up my petrol tank to full and as I was pulling out of the petrol station the car stalled and wouldn't start.
This keeps happening every time I fill it up, I can just barely drive it as long as I keep my revs up, but if I start to slow down (when approaching traffic lights etc) the car just stalls.
My check engine light is on but a mechanic just said that was because of a sensor and I don't need to worry about it, I'm not very good with cars so didn't really think much of it.
I can also smell petrol sometimes and when I unscrew my cap on my tank it sometimes hisses (is this normal after driving 30 minutes?)
Accent MC (2006-11) :: Cylinder 1 Misfire
What is the easiest fix on this and what is the worse case scenario?
View 6 RepliesLexus GS 2006-11 :: Car Started On Petrol, Not Electric Power
I went to look at a 2009 GS450h today. Great car and looking to buy but have two questions:
Firstly, when I sat in and pressed the Power button the car started on petrol, not electric power, which I wasn't expecting as i understood the 450H always starts on battery. Am i right or getting mixed up?
Secondly, and maybe linked to the above, when I looked in the boot (trunk?) the cover was off the small battery located on the lh side. I suspect they may have been using a booster pack to get the car going (as car dealers often do) but isn't this a big no no for the 450H.
Accent MC (2006-11) :: 2007 - Cylinder 1 Misfire
I am currently having an issue with my 07 Accent misfiring on cylinder 1. So far, I have changed the spark plugs, which were due anyway, and checked the coil pack. Every coil on each cylinder reads 0.8 ohms, so I am going on the assumption that they are ok. Didn't see any issue with the connector end inside the boot. However, when I changed the plugs, I discovered that I had oil in the plug tubes on 1 and 4. So I changed the valve cover gasket and tube rings and cleaned all oil residue from the packs. I have also checked the short coil wire harness right on the packs themselves. Have not tried to check further because I don't know which pins that harness goes to on which ECM connector. I still have the misfire, and I'm not sure where to go next. I was thinking compression or fuel injector. I don't have a compression tester, and I assume the only way I can check the injector is to swap it with another cylinder?
View 10 RepliesAccent MC (2006-11) :: Multiple Cylinder Misfire
My car has been really acting up lately (AGAIN) so I took it in to have it looked at and they came back and told me it had multiple cylinder misfire, and they wanted like $1200 to fix it. What in the world does that mean and what is entailed in fixing it? They mentioned doing a full maintenance on it.
View 9 RepliesAccent MC (2006-11) :: 2007 - Cylinder 3 Misfire
2007 accent randomly starts missing. throws cyl.3 missfire. replaced all plugs and cyl.3 coilpak.
View 2 RepliesAccent MC (2006-11) :: CEL After Misfire - Cannot Get Over 60 And Sometimes Drops Down To Maxing At 50 MPH
i have a 2010 hyundai accent base model with 84,000 miles, recently i fixed my misfire/P030X codes. worked fine for about a couple days then CEL P0420 code came on and performance dropped dramatically. Replaced both o2 sensors and erased codes, drove for about 50-60 miles no CEL but still bad performance. cant get over 60 MPH and sometimes drops down to maxing at 50 MPH. Looked down exhaust manifold with O2 sensor out and saw an intact honeycomb for the cat. What to try next.
View 7 RepliesAccent MC (2006-11) :: 2009 - Misfire On Cylinder 3
I have a 2009 Accent. It has a misfire on cyl 3. I've changed the spark plugs... no change. I swapped around the coils... no change. The misfire stays on cyl 3. What are my next steps to isolate and resolve this misfire?
View 10 RepliesAccent MC (2006-11) :: Several Error Codes - Cylinder 3 Misfire
My 2011 Accent's engine light came on recently. The mechanic said it was a cylinder 3 misfire and recommend changing the spark plug and coil pack for that cylinder. We did that over the weekend. Now the light is back on and has read 5 codes in the past 12 hours (4 at one time). They are P0303, P0304, P0003, P0403, and P0100. I have looked the codes up and can't discern if any could be caused by one main issue. About a month ago it read a code for the oxy sensor, but it went away and never came back.
View 3 RepliesAccent MC (2006-11) :: Hesitation Or Misfire When Accelerating From A Stop
I have a 2010 accent 2.0 with 110k. When accelerating from a stop it seems to hesitate or miss in the first 20 ft or so. The service engine light has not come on which indicates to me it's not in the emission sensors. Where to start looking?
View 10 RepliesAccent MC (2006-11) :: Misfire On 2 Cylinders - Location Of MAF Sensor?
I have a 2009 Hyundai accent. 2 cylinders misfire. I changed out the spark plugs after the misfiring began and the 2 cylinders that misfire don't follow any specific ignition coil, it's just 2 random ones.
Looking at the data with a reader points to fuel injector number 1 not working properly. The first few seconds the car is on the check engine light blinks and fuel injector 1 spray duration (fluctuates based on gas applied) changes just like all the others. However, when the check engine light goes solid (then the misfire code is thrown) fuel injector 1's spray duration is stuck (usually around 3.5 ms)
The cable going into the fuel injector powers those little troubleshooting lights like it should until you plug the cable into the fuel injector OR remove and replace the light a few times.
I don't know much about cars but someone told me to try cleaning out the Mass AirFlow sensor as they had the problem above and the MAF sensor was the cause. I can't find anything on where the MAF sensor is located though.
Accent MC (2006-11) :: Misfire With Error Code P0302
2009 Accent, 1.6L 154,xxx Cylinder two misfire. Engine was rebuilt due to timing belt. Twice. Second time I did it. Replaced plugs, coil packs, all gaskets, (everything new in the head) did a smoke test, compression test 180 psi across all four, used a noid light for coil packs (good) did it at the injectors 1,3,4 did good, but 2 came on then went off. Check resistance and it shows good, replaced injector anyway and the connecter. Still doesn't work. Checked powers and grounds at the rail, good. Good solid voltage. I hooked up a scan tool and tried to shut injector 2 off, no change in RPM or vibration. Scan tool worked for 1,3,4. Used another PCM, still misfire in two. Even jumped a wire from PCM control and 15A inj fuse for the 12V constant (bypassed the harness) and still doesn't work. Also have knock sensor code, just two codes.
View 14 RepliesAccent MC (2006-11) :: MIL Flashing And Car Starts To Misfire Significantly
Started with trouble starting right after a fill up. Right before I was to replace the evap purge valve, I filled up and on my way home, the MIL starts flashing and the car starts to misfire significantly. I replaced the purge valve, but no change in performance (though my car now started up right away after filling it up!). I would drive the car and it would misfire while idling at a light, backing up out of my driveway, accelerating on flat and inclined roads, etc. Codes were 300, 301, 303, and 337 (misfire, misfire, misfire, crankshaft position sensor low voltage)
So, I replace the crankshaft sensor with OEM (this is my 3rd one and this sensor going bad has caused different symptoms each time. First my car would cut out and die while turning, second it would not allow the car to start, and now presumably rough idle). Now the car starts up with less cranking, but still runs rough and misfires (only 301 this time).
So, next I replace the plugs with NGK V's gapped at .044. Better, but not perfect. I noted that the plug in cylinder 1 was darker than the rest.
I read on thread here about regapping to .035, so I tried that. Again, I noted that cylinder 1 plug is slightly darker, while 2-4 have a slight white coating. After the regap, runs great, no misfires, smooth acceleration, perfect...for 24 hours.
On day 2 I start to feel a slight misfire going up a hill, and sometimes at a red light or accelerating from a stop...but not all the time.
Now its day 3 and similar to day 2. Not since I regapped the plugs has the MIL been on, so the misfires are hard enough to feel, but not enough to trigger the MIL.
Not sure where to go next. The coil packs were replaced last year (35,000 miles ago). The car has 137,000 miles on it.
Sonata NF (2006-10) :: Misfire On Cylinder 3 And 6 - Running Rough When Slow Down The Car
When I'm driving and get above 50-60 I will get the Check Engine Light. Check the codes It shows 6 ---300, 303, 306, 300, 303, 306. When I slow the car down it is running rough, almost like it has a miss.
I reset the computer while this is going on and the engine smooths out and it runs correctly until I keep my pedal down and then it kicks the exact same errors.
Here's strange part number one: Once I get down to about a gallon or two of gas in the car everything seems to run fine. I have plenty of power, no codes and the car runs fantastic!
Strange part number 2: Very occasionally When I get in the car in the morning to go to work, the car is a bit difficult to start. When it finally kicks over, it is immediately running rough. resetting the computer with the engine running does not seem to stop the rough running. If I turn off the engine and let the car set for a bit it will start and run fine, with the exception of the first problem mentioned in this thread. There is no code while it is running rough, but when the Light kicks on as per the first issue mentioned, I have an additional code -- 335. This car has been excellent up until the last few months when this issue developed.
Accent MC (2006-11) :: Misfire / Car Stumbles On Acceleration And Idles Sporadically
After almost an entire year of trouble-free running (with the exception of replacing a ground strap), my 2009 accent decided to start bucking and shuddering again. It only does this when warmed up, runs perfect cold. In the last 16 months, I've replaced the plugs, coils, battery, PCV valve, and ground strap. Car starts with zero hesitation.
Strong battery and starter, consistent output from alternator. After @5 miles, the car stumbles on acceleration, and idles sporadically. While looking at it tonight, I noticed a few exhaust brackets under the car had broken, and the flex section of the intermediate pipe had torn open. Could this presumed exhaust leak be causing the crap running performance?
My "exhausted" brain thought it could cause the O2 sensor to misinform the ECM, resulting in the P0300 code I pulled...