Hyundai - Elantra :: 2002 - Rough Idle And Misfire When Hot / Intermittent Hesitation When Accelerating
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
Lexus ES 2013+ :: Hesitation When Accelerating From Dead Stop
Our 2015 es350 with 2,500 miles hesitates when accelerating from a dead stop, such as from a stop light. We are told this is to be expected with this vehicle. The dealership test-drove the car and say there's no problem. But this hesitation is unlike any other car we've experienced.
View 8 RepliesCadillac :: 1959 - Hesitation From Stop When Accelerating Just Initially
My cady hesitates from stop when accelerating just initially and then runs fine while driving. I have changed plugs, electronic ing, wires cap, rebuilt carb fuel filter. What can be causing this???
View 10 RepliesPassat (B5) :: Hesitation When Accelerating From A Stop / At Half Throttle Car Bogs Down
I have a '99 passat 1.8t Tiptronic. 106,000 miles. Recently I've been getting a bad hesitation when accelerating from a stop. At half throttle the car kinda bogs down and hesitates then as the rpms get higher it seems to clear out and accelerate smoother. At the same time the car doesn't have the same sack it used to. I checked he plugs, found them very fouled. Replaced them and the problem got a little better, but definitely still there. There has to be a reason the plugs fouled. There is no CEL so I don't really know what to check first.
View 2 RepliesLexus LS 2007+ :: LS460 - Hesitation / Lack Of Power When Accelerating From A Stop
I have a 2007 LS 460 with about 50,000 miles. Some 18 months ago, at about 35,000 miles,right after a service, I began to experience hesitation/lack of power when accelerating from a stop. Lexus fixed this by doing a software update to the transmission.
All was well till last month, when again right after a service, the car hesitated and totally lacked power , most noticeable from a rolling stop. Revs would very gradually climb to 5,000, with foot flat on accelerator, yet car barely moving. Once speed built up to highway speeds, car reacted normally. Took it back to Park Place Lexus who held the car for 10 days and did a major job changing the cylinder head, I think per L-SB-0033-08.
A month later, the hesitation/lack of power is even worse then before! I suspect the issue is the transmission, and the big surgery on the engine done last month was not required. After nearly being hit trying to merge with traffic today, the vehicle is back at the dealership, and I took their head tech for a drive. He experienced the problem, but did not venture a solution. He told me they take instructions on what to do directly from Lexus.
Buick - Century :: 2003 - Hesitation Then Jerks A Bit After Coming To A Stop / Accelerating
I have 2003 Buick Century. I started having problems with the car after coming to a stop, accelerating - the car starts to go hesitates, then jerks a bit to go. This does not happen every time after a stop but when it does the service engine soon light comes on. Initially I got the P0401 code (I think) and took it in to a mechanic. They could not find anything wrong with the car but did clean out the EGR valve, that didn't work, they worked on my transmission and replaced other parts, still no success.
I took the car to another mechanic who replaced the EGR valve and several other small parts. I still had the problem but this time the error code was P0420. I took it back again and replaced the spark plugs, O/2 sensor, catalytic converter. That hasn't fixed the problem. The mechanic said that they have taken my car for several test drives and the car has not demonstrated the problem. The error message still reads P0420 even after all of the parts have been replaced. The 2nd mechanic has washed his hands of my problem.
Ford Super Duty (1999-2016) :: Hesitation When Accelerating Or At A Stop
F250 5.4L have had a new fuel pump installed and new spark plugs (one blew out). When accelerating, or at a stop i get a kinda hesitation. It did it when I first bought the truck but put correct size tires on it and it went away. What it may be? I don't have a check engine light or anything and at cruise speed no problem--it's just when a slight load is put on the engine?
View 1 RepliesAccent LC (2000-05) :: Cylinder 3 Misfire / Massive Hesitation Under Heavy Throttle
I've got a 2000 accent 1.5, and I keep getting a code for a cylinder 3 misfire, when I change the spark plugs, it runs great for about 50 miles or so, then back to square one again. I just changed the coil pack the other day and there doesn't seem to be much of a difference. It has massive hesitation under heavy throttle, and the check engine light begins to blink if it sits and idles for too long. I've scanned it multiple times and it's always been cylinder 3, so it's definitely set on that one... I'm about stumped on what this could be. Also, the previous owner said that after a hot day of driving, the ECU fuse under the hood will blow out, what could cause either one of these things?
View 40 RepliesAccent RB (2012+) :: Squeaking Noise After Accelerating From A Complete Stop
I bought a 2012 Hyundai Accent GLS just two days ago. It has about 38,000 miles on it. It's an automatic as well. I drove it home on the highway and was averaging about 44 mpg the entire time. Even while driving in town, it's got pretty good fuel economy. Everything about the car is great.
However, last night, I was driving around. When I came to a stop at a stop sign/red light/etc. and then proceeded to accelerate, I would hear this weird squeaking / creaking sound. I've heard it multiple times now since then. It doesn't do it every single time I accelerate, but when it does, it lasts for about 3 seconds and then stops. I've also noticed it does it sometimes when I make a turn and then accelerate. It's just a squeaking sound.
Is this something I should be concerned about? It doesn't do it every single time I accelerate, but when it does, it will last for about 3 seconds. I should also note that the car made the noise the first night after I had been driving for a while, so the engine wasn't cold or anything.
Sonata NF (2006-10) :: 2007 - Severe Hesitation / Car Almost Quits On Accelerating From A Stopped Position
I purchased a 2007 Sonata with the 3.3L about six months ago. I really like the car, it has a lot of good features and lots of power; however, I am starting to have problems with the car. On accelerating from a stopped position the car almost quits (hesitates severely) and then picks up and goes on normally. Also, between 40 and 50 mph the car starts to jerk pretty hard for a few seconds and then it straightens out and runs normally again; it will do this repeatedly if it is kept between 40 and 50 mph.
When this first started happening the CEL would come on randomly and stay on for a day or two and then go off. While the CEL was on I took it to Autozone and had them pull the code, they said it was the crankshaft position sensor. Well based on the symptoms the diagnosis made sense. I replaced the sensor and the car seemed to be running normally on the 30 minute test drive. The next day my wife drove to work and she said the same symptoms had come back. It has been several weeks since I replaced the sensor and the CEL has not come back on. I have seen several postings about the spark plugs and wires and that is my next step. BTW the car has 94k miles.
Accent MC (2006-11) :: Hesitation Or Stumble On Light Acceleration That Come And Go
My 2011 stick shift no air Accent has a hesitation or stumble on light acceleration that comes and goes. It may not occur for weeks then re-occurs. It is hard to reproduce intentionally. It never occurs in cruise. The CEL is not on. Most often occurs at 1400 to 1500 rpm with slight acceleration or a slight increase in load as coming to a slight hill. I tried injector cleaner a few times and changed air filter. It seemed more reloaded to induction airflow so I changed the MAP sensor. I understand the 2011 Accent does not have a MAF sensor. It is still occurring. It is fine in steady cruise as well as in hard acceleration. I am wondering if it is a TPS sensor problem. It has 60,000 miles and otherwise runs fine.
View 4 RepliesAccent MC (2006-11) :: 2009 - Hesitation When Turning Over To Start
The wife's accent started hesitating when turning over to start. Like turn the key, engine will turn 1/4 turn, then nothing for a second or 2 ( without releasing the key) and then crank and start fine.
Checked connections at the battery, cleaned 'em. No CEL on.
I had a ignition cylinder freeze last winter, when my wife dropped her key in the snow and put it in with water on it. Had to heat the cylinder with a small lighter-style blowtorch and put low temp graphite in there.
Did I maybe melt something in there?? Something else??
Ford F-150 (2004-2008) :: 2006 - Stumble When Accelerating Around 45 MPH - Misfire On Cylinder 5
i just picked up an 06 f150 with 5.4l 4x4 xlt package. Love the truck as it is my 1st Ford HOWEVER..... the truck is running super rough at idle and keep getting code for cylinder 5 misfire and bank 2 lean (which i am assuming is from cyl 5). here is what i have done so far...
New Coil packs
New spark plugs
New fuel module
New fuel injector on cyl 5
Still has a "stumble" when accelerating around 45 mph and shows code for cyl 5 misfire then will then throw code for bank 2 lean.
Accent MC (2006-11) :: Cylinder 1 Misfire
What is the easiest fix on this and what is the worse case scenario?
View 6 RepliesAccent MC (2006-11) :: Car Shakes When Accelerating And Going Uphill
2010 Hyundai Accent GLS (automatic)
Just noticed the last few days that my car has developed a shake when accelerating, but stops after a certain speed. It isn't bad yet, but when I started going up a hill today it was significantly worse. The entire car started shaking, but stop after the car leveled out.
I just put in a new front left and right axle two weeks ago, would that have caused anything ?
Accent MC (2006-11) :: Lateral Vibration While Accelerating Between 40 - 60 MPH
I have a lateral vibration while accelerating between 40-60MPH. There is no vibration if the car is at constant speed, decelerating or if I drive, at that speed, with the clutch depressed.
The problem persists in spite of having aligned and balanced the tyres, a few days back. Subsequently, I again rotated the tyres because the mechanic insisted that it was a tyre and rim issue. But no luck! The tyres are in great condition and the rims aren't damaged.
Visual inspection of the under body also revealed no obvious problems except for slightly leaky rear shocks.
The car is a 2009, Hyundai Accent sedan, 1.4 litre petrol.
Accent MC (2006-11) :: 2007 - Cylinder 1 Misfire
I am currently having an issue with my 07 Accent misfiring on cylinder 1. So far, I have changed the spark plugs, which were due anyway, and checked the coil pack. Every coil on each cylinder reads 0.8 ohms, so I am going on the assumption that they are ok. Didn't see any issue with the connector end inside the boot. However, when I changed the plugs, I discovered that I had oil in the plug tubes on 1 and 4. So I changed the valve cover gasket and tube rings and cleaned all oil residue from the packs. I have also checked the short coil wire harness right on the packs themselves. Have not tried to check further because I don't know which pins that harness goes to on which ECM connector. I still have the misfire, and I'm not sure where to go next. I was thinking compression or fuel injector. I don't have a compression tester, and I assume the only way I can check the injector is to swap it with another cylinder?
View 10 RepliesAccent MC (2006-11) :: Multiple Cylinder Misfire
My car has been really acting up lately (AGAIN) so I took it in to have it looked at and they came back and told me it had multiple cylinder misfire, and they wanted like $1200 to fix it. What in the world does that mean and what is entailed in fixing it? They mentioned doing a full maintenance on it.
View 9 RepliesAccent MC (2006-11) :: 2007 - Cylinder 3 Misfire
2007 accent randomly starts missing. throws cyl.3 missfire. replaced all plugs and cyl.3 coilpak.
View 2 Replies