Accent MC (2006-11) :: CEL / OBDII Code P0141 - O2 Sensor Heater Circuit Malfunction
CEL/OBDII code P0141 - O2 Sensor Heater Circuit Malfunction
So I just bought this car 64k well maintained but cant get rid of the check engine light. Replaced downstream O2 sensor with no luck. As soon as I get home I'll check voltage @ connector. Lets test the O2 sensor connection and test the pins to make sure there is no break in the wires.
Accent LC (2000-05) :: ECU 1 Fuse Keeps Blowing - System Voltage Low Code
I have a 2005 accent that keeps blowing the ecu 1 fuse. It is also showing a code for "system voltage low", and the battery is wet around both posts. I read somewhere else that the alternator could be surging and blowing this fuse. Had both alternator and battery checked at autozone, battery is said to be on the way out and alternator shows its fine. Battery does not show any problems, start car just fine.
View 7 RepliesYaris/Scion & Vitz :: 2000 Echo Started Missing - Code Check Came Back With P1315 / P0141 And P0304
The other day my 2000 Echo started missing, she would run fine until after about 5 mins. After that, it would run like it was only running on two or 3 cylinders so I took her to Auto Zone for a code check--it came back with p1315,p0141 & p0304. On the way home it really got bad! She started dying on me. Just like u turned the key off. Before coming to a complete rest I turned the key all the way off and back on and she ran for 30 seconds or so - You would have to turn her all the way off--back 2 clicks--one click back would not work and this is the way I got her back home--about 7 miles turning her on and off. I wish now I had not hooked her up to there code checker because I think it burnt something out.
View 6 RepliesFord Excursion :: 2000 Truck Would Not Shift - Fuse Blown
About three weeks ago driving. My truck would not shift come to find out it was a fuse that blew. Well I pull over and replace the fuse it starts right up I get about a mile from my house and it blows again so I shut off my x and then replaced the fuse. Will not start...
Now I am getting a Pats code 1:6 and my obd2 reader says no link on my x. It used to read it all the time. I am trying to figure out what I can check to fix this problem are there any relays. Oh also my check engine light does not come on when I turn the key but my truck does crank. does this mean there is no power to my ECU. I did replace my ecu and it did not solve the issue.
Yaris/Scion & Vitz :: 2000 - Fuse Blown While Installing Aftermarket Stereo
I put in an aftermarket stereo. It has been a while since I have done that and somewhere along the wiring process I made a mistake and blew a fuse. I knew the lights around my speedometer weren't working but what I didn't realize is that my running brake lights weren't working, it took me about two days to realize this.
I fixed my wiring mistake and started looking for the blown fuse. I found one (I believe #19 inside the vehicle) and replaced it. This fixed my running brake lights and half of my instrument cluster. The lighting on the right side of my speedometer seems to work but to the left of it seems to be no light.
Also, I have an automatic car starter and before I jacked things up when I use to start it and the blinker lights use to come on and let me know that my car was running. I have checked the majority of the fuses(I believe all of them) and it doesn't seem that I have anymore blown fuses.
[URL].............
Ford Super Duty (1999-2016) :: 2000 F250 - Horn Stays On / Fuse Blown
Horn isn't working found fuse blown. Replaced fuse and horn stays on. Swapped relays still stays on. With fuse out pressing left side of horn cover on steering wheel I can feel/hear relay click. Pressing right side not so much. What and where to check? Is there a way to disconnect the horn buttons on the steering wheel?
View 1 RepliesGolf IV / Jetta IV :: 2003 - Got Error Code P0420 And P0141?
I just bought a 03 2.0 and ive been trying to fix her back up, she is almost there, just waiting on my first gear getter from diesel geeks and trying to figure out why these codes (p0420 and p0141) keep coming back on. Originally it was just a p0420 code so i took out the upstream sensor and cleaned it, then i took out the backstream and after examining it figured it should be replaced.
I went and bought a new one and replaced it, within the next 2 days the check engine light came back on throwing the original p0420 code along with p0141 this time. So i took out the new down stream 02 sensor and took it back to autozone and they swapped it out with a new one for me free of charge. So i put the newest 02 sensor in and then within 2 days, both codes p0420 & p0141 came back on. Two 02 sensor heating wires being bad i feel is a pretty slim chance. What is possibly the cause for these two codes repeatedly being thrown?
Accent LC (2000-05) :: Brake Lights Keep Blowing The Fuse
I have a 2003 Accent and I'm having a problem with the brake lights not working. The tail lamps work when the night lights are turned on so it's not a bulb issue. The brake lights keep blowing the fuse. Brake lights will only work with a fresh, new fuse but only works for about a trip, give or take and then its blown.
View 1 RepliesAccent LC (2000-05) :: Lights On Driver Side Won't Work - It Is Fuse?
All my lights on the driver side don't work, replaced brake light and then nothing. Would it be a fuse? if so which one or wiring and how would I go about finding the fault.
View 1 RepliesImpala - Chevrolet :: 2005 - P0141 Code Did Not Stop Occurring After Both Sensors Changed
I have a 2005 Impala with the 3.4 engine and 118,000 miles. About 2 years ago I had a code P0141 and since we didn't know for sure which oxygen sensor was out we replaced both of them. The P0141 code did not stop occurring after both sensors were changed. I read on an Impala forum that if you didn't replace the sensors with AC Delco the codes would continue so I didn't worry about it until my gas mileage starting going down recently. I ordered new AC Delco oxygen sensors and my husband replaced them Saturday, the old ones were sooted up pretty badly. Today a new code appeared, it is P0140, O2 sensor circuit no activity. What the problem might be now.
View 7 RepliesFord Ranger / B-Series :: 1996 2.3L Automatic - Check Engine Light Came On / Error Code Is P0141
My 1996 Ranger runs ok but my check engine has come on. Using a scanner tool, indicates my cat monitor wont go to ready state and my error code is P0141. According to my research it indicates one of my 02 sensors. How to determine if its the one before or after the cat converter? About 6 months ago I had an exhaust leak repaired around my converter so I know I cant return it under warranty . If its the rear sensor , It looks fairly easy to replace but the front sensor looks a bit cramped.
View 6 RepliesFord Super Duty (1999-2016) :: 2009 V10 - Wont Go Past 3000 Rpm - Got Code P0141?
Yesterday I punched it and seemed the truck was a bit doggy at higher rpm, the cel blinked but no codes, drove it all day today and it still seemed "not normal" I punched it and it wouldn't go past 3000 rpm and its so doggy it barely moves got a code po141 engine seems like its super lean? This happened on my way home luckily about a mile from my home.
View 2 RepliesAccent LC (2000-05) :: 2002 - Code P0106 / Map Sensor Code
Ok had a check engine light. It directed me to replace the IAT sensor.. After some research I found it was integrated into the MAP sensor. Purchased a new sensor and replaced. Drive about 15 miles CEL throws another code. P0106 (sensor i just replaced) faulty Map sensor.
Followed procedure to replace sensor.. unhook battery cable reset ecm. After reset engine is hard to start. Followed by RPM changes (assuming its the ECM re-adjusting). Then CEL flashes 5-6 times and goes out, Drive 15 miles. Map sensor code reappears. (note i only purchased one sensor But repeated install 2 times).
My thought is against wiring. since the codes refer to different signal wires one for IAT one for MAP sensor. Faulty replacement sensor?
2002 Accent 1.6L
Gmc - Suburban :: 1991 - Fuse Keeps Getting Blown
My fuse keeps getting blown, mechanically and emotionally. My 91 gmc suburban blows the a/c fuse every time i slide the a/c switch to any position. when the fuse goes my emergency brake light turns on and my speedometer stops working. one weird note, my engine seems to run very smooth after the fuse goes, to the point that im not even sure its running but it is. So my question is, where should i start looking to fix the problem? It's too hot/cold in here!"
View 2 RepliesWindstar :: Air Bag Fuse Blown When Turn On Ignition
What would cause the air bag fuse to blow as soon as I turn on the ignition?
Have tried replacing the fuse and this happens (fuse blows out) each time.
95 3.8L... nearly fully rebuilt.
Prius (Gen 2) :: Cigarette Lighter Fuse Have Blown
So I have an Android smartphone. That I always put on the charger in my 2005. However. I have blown the fuse to the cigarette lighter. Both the one in the center console and the one under the passenger side dashboard.
The last time that happened. I bought the indicated 15 Amp fuse (as the Owner's Manual indicates - vaguely) Only to find that swapping out fuse 20 IIRC. Yielded no power to those ports.
Celica :: 1994 - 100 Amp Alternator Fuse Blown
Just picked up a 1994 1.8 celica hatch and it was told to me that the 100 amp alternator fuse blew and there was some issue. So far haven't found any but I also cant seem to find this 100 amp alt fuse that goes in the fuse box under the hood. I don't have old one.
View 1 RepliesPrius V :: LED Lights Are Not Working - Blown Fuse?
So I added in a set of LED lights for my license plate and parking lights. In addition to HID's for the headlights tonight. At some point my tails/parking & license plate lights shut off. I assume its a fuse, I'm wondering if this is common or the result of low quality product.
I've used the same installer/lights on every car I've had for the last 5 yrs and never an issue. No issues in my Scion Xd, Mustangs and so on.
Touareg :: Horn Broke - Fuse 16 Was Blown
I don't use my horn unless absolutely necessary. Well, today it was. Guess what? The Sounds of Silence. No horn, no how.
Turned out, the No. 16 fuse was, in fact, blown. What caused that, I don't have a clue. Replaced it and it is working again. Hopefully, not a harbinger of electrical gremlins to come.