Saturn - Vue :: Repair And Maintenance - Rear Wheel Speed Sensors
Is there some common issue with this? Purchased the vehicle new in 2008, and in 2011 we have had to have the car in for this issue at least once a year. They replace one, then the other, then back to the first one, and now it appears the second is not working again. Each winter we run into this. The dealer will only warranty for a year, so I am paying each time.
View 1 RepliesSonata NF (2006-10) :: How To Repair Or Rekey New Ignition Lock
My car was having the problem with key not turning and was getting worse over time. Finally decided to replace it, but didn't want two sets of keys or to replace all locks in the car or pay dealer $550 to do it for me.
I bought the new $135 lock from the dealer and swapped the tumblers out from the old unit. Here is my document on how to do it. [URL] .....
Ford - Explorer :: 2002 - Ignition Lock Replacement?
Lock cylinder needs replacing. Was stuck in the off position and would not rotate. Finally freed it up so I can remove the cylinder.
Question is, will the key that comes with the new cylinder need to be programed. If so how is this done?
Ford Escape / Hybrid :: 2003 - Ignition Lock Cylinder Replacement
I'm replacing the ignition lock cylinder on my 03 Escape. The factory cylinder has the little black "wings" that nestle around the key when inserted:
The locksmith says the replacement cylinder needs to have those same wings for him to be change it. Is this correct? The auto part stores have the regular cylinder (with no wings) readily available, but the one with wings is a special-order item and I need this sooner rather than later.
Plus, the wingless one includes keys while the other appears to have none.
Yaris/Scion & Vitz :: 2001 Toyota Echo - Ignition Lock Cylinder Replacement
The previous owner broke the key off in the ignition so I replace the ignition lock cylinder the problem is though even with the old one I can't turn the key to lock so it's stuck on acc. What I can try without replacing the entire column? Also it needs a catalytic converter, do I have to weld a universal one on ?
View 1 RepliesFord Ranger / B-Series :: 1996 - Ignition Lock Cylinder Won't Reinstall
My keys got stolen from my ignition (battery had died because key was left in ACC and I assume the attempted car jack ended in a key theft for some reason.)
The Ranger is 96, tilt steering with plastic shrouding and column shift A/T... I followed the procedure recommended for exchanging the cylinder without the keys:
-drilled retaining pin
-drilled key slot
-manually removed parts with needle nose
-cleaned, greased and went to reinstall.....
I discovered the small metal washer between the green plastic washer and the gear was broken in half because I nicked it with the end of the drill bit. I inspected this and from what I can tell it looks like the green plastic washer is designed to hold onto the metal washer, the two of them together, from what I gather are designed to keep the gear from moving sideways or tilting. I figured that the washer should do it's job even in two pieces if I could get it in there straight and get the green washer to grab it.
Anyway I stuck it all back in there, slid the new lock cylinder in in run position, and nothing good happened. It's in the whole way, I can see the retaining pin centered in the whole from underneath, but when I try to seat the retaining pin it won't budge. I tried to align the parts at a million different angles and I just have no luck. I am planning on replacing the little metal washer, but I don't feel like it being broken alone is enough to keep all parts from functioning properly. I am stumped because I did the procedure step for step and there is nothing else apparently broken or damaged. The only other factor is that the steering wheel is locked and that sometimes made the other cylinder hard to turn, but it freed up usually with a little wiggling, this cylinder won't budge.
Saab - 9-5 :: Maintenance And Repair - Fuel Pump Is Going Out
I have a 1999 Saab 95, auto, 4 cylinder. I believe the fuel pump is going out. The car will sometimes stall at a stop light and when I stepped on the gas hard it sound/feels like it's stalling but gets going again!! I already checked the fuse, what else can it be? The car has of 100k on it and it's the original fuel pump.
View 12 RepliesMaintenance / Repair :: Headlights Not Working After Oil Change And Tires Rotated
I recently went to a local chain to have my oil changed and tires rotated. Later that evening when I went to turn on my headlights for the first time since the oil change neither one was working. When I brought back the car the next day to see if they could look at this to see if anything reset accidentally I was told that both lights were burned out and it was a coincidence. It seems unlikely that both headlights would go out at once (high beams were OK) and that it would have happened right after the oil change. I couldn't say what would have caused this but wanted other opinions on if it was likely related to the oil change.
View 19 RepliesSuzuki - Aerio :: Maintenance And Repair - Slight Wavy Pattern On Front Windshield
We just purchased an Aerio for my teenage son. We all just love the car. It is the base sedan with 5-spd. There is one problem we did not notice on the test drive. It seems that when the front windshield was made, there is a slight "wavy pattern" that you can see. While it does not inhibit your vision, it is a little irritating.
View 30 RepliesIgnition - Saturn - Sl :: 1999 - Engine Misses / Low Power - Ignition Control Module?
My 1999 Saturn SL1 was running well. One evening, I started it up to go home, and it wasn't running well, and barely had power to make it the half mile home. It still starts up, but seems to miss in park and in gear. We tried spark plugs, wires, coils, catalytic converter, cylinder pressure, crankshaft position sensor, and fuel filter with no change in engine behavior. I think the EGR valve was looked at and passed. I hope it is not the fuel injectors as I put a cleaner in the fuel every so often. Could it be the Ignition Control Module, and is there a way to test the existing module? What else could it be, and how could I test it?
View 6 RepliesSaturn - Ion :: Making Noise After Maintenance
After having my car serviced at Halvoline Xpress Lube it immediately made a noise when I turned on the heater / vent. It sounds like "grrrrrrrrrrr" and there is a vibration in the dash and a little bit of vibration in the steering wheel. It feels like the car pulls a bit when I have the vent turned to the highest setting. The higher I turn the vent, cool or heat, the louder the sound.
The work they did was:-oil change-rotate tires-pulled out two filter to show me the condition then put them back
I took it back a couple weeks later, they checked the filters, said they were fine, checked stuff, I don't know what but they seemed earnest in their efforts. They took the glove compartment apart and poked around. They couldn't understand how it was related to their work and suggested I go a mechanic and keep them posted.
It's either an amazing coincidence that when I pulled out of their garage my car developed a problem, or that they did something goofy and don't know what it is.
Repair :: Driver Side Brake Keeps Trying To Lock Up?
My driver side brake keeps trying to lock up and then my brakes get really hot. How do I get them to let go while driving?
View 3 RepliesMaintenance / Repairs :: Car Won't Start - Clicks With Ignition Off
My son's car wouldn't start after parking at burger king. In off, the car has clicks just behind the floor shifter in a black module and under and foward of engine compartment fuse block. Only way to stop clicking is to move ignition switch to another position or pull IB Battery MaxiFuse in engine compartment fuse block. No activity from car in any other ignition position. no instrument panel lights, radio.
Thought ignition switch changed it, same condition. Battery checks out good. jumpstarting even using a second ground on engine doesn't change symptom. I can't find the modules that are clicking in my Chilton manual. What are the clicking modules and how can I move forward to get the car out of the burger king parking lot?
Lexus GS 2006-11 :: 2007 - How To Repair The Trunk Lock
I have a 2007 GS 350 in which the electronic lock that you push on the outside of the trunk to open the trunk has gotten capricious because its external rubber has deteriorated. So I want to change it. The replacement part is readily available at the dealer and the parts guy said it is apparently not complicated to replace. But before doing that I need to remove the carpet padding on the inside of the trunk lid so as to get to the part to replace.
How to do that? There are what look like plastic screws holding the carpet lining in place but unscrewing does not seem to looses them. I removed one by pulling hard on it. Don't want to do the same to the rest in case that is wrong.
Also, it looks like the safety unlock handle and actual lock are obstacles to removing this lining. Do instructions exist somewhere for how to remove this carpet lining off the trunk lid?
Maintenance / Repairs :: 2002 VW - Function Of Windows And Lock Buttons Swapped?
OK I have a 2002 VW Bug TDI and yesterday I got into the car and the windows, sunroof, and mirrors did not work all are power. Now for the fun part. When I leaned over and tried the window button on the passenger side the doors locked. So on the drivers side the window buttons do nothing and the lock button work just fine. On the passenger side the the lock button does nothing but the window button locks and unlocks the car. As best as I can remember the windows worked normally on Monday. I have not looked at the fuse box but would that cause the window button to work the locks?
View 3 RepliesFord Ranger / B-Series :: 1988 - Press Key Lock To Remove Key - Disable Key Lock?
On my '88 Ranger, there is the key lock that needs to be pressed to remove the key. When I changed the ignition cylinder, I darn near went ahead and removed it. I though I better check here first, and see if I was going to disable some other function I don't know about.
View 1 RepliesIgnition - Toyota - Repair - Celica :: 1999 - Light Turned Green Put It In Park Now Won't Start - Making Whining Noise?
It's a 1999 Toyota Celica GT 2.2L, about 190000 miles and I just replaced the transmission not too long ago. Here's what happened, I was sitting a light, the light turned green, and I pushed the gas and the car stalled. I put it in park, tried to turn it on, and it won't start, but is still turning over, making an awful whining noise. Not the transmission. Battery is good, windows, stereo, etc still work. Terminals are good. Everything is still connected, I just changed my oil about 1000 miles ago, still has oil. Has transmission fluid, actually has all it's fluids, no leaks. No check engine light or any other lights. She did not overheat, if anything was colder than usual, No water in my motor, everything LOOKS good, and I take good care of my car, so I'm really baffled. I just spent my savings on the transmission, I'm not a mechanic, I'm just learning to do things on my own.
View 19 RepliesToyota - Repair - Corolla :: Loudest Rumbling Exhaust Sound / Catalytic Converter Replacement?
Yesterday my 1995 Toyota Corolla (which runs well otherwise) started making the loudest rumbling exhaust sound I've ever heard whenever I stepped on the gas pedal. It also felt like it had trouble accelerating when I would try to get going after a stop. I took it to a mechanic right away, who says it needs a new catalytic converter and resonator pipe.
My boyfriend says this is a repair he could do. He has done some car repair and worked with a mechanic before, so I am considering trusting him on that, but I don't know what types of repairs he's done before and I know he has never worked on this model. What would you take into consideration whether or not it would be safe to attempt this repair at home?
Saturn - Ion :: 2002 - Won't Start - Key Stuck In Ignition
I have a Saturn Ion 2, 05. I will intermittently not start. I put the key in the ignition, power comes on, turn the key, it clicks a couple of times and then everything turns off. The key is then locked in the ignition. It is a new key. My old key looked chewed up. The only way to get the care to release my key is to open the hood and wait a few minutes and then shut the hood. Power will come back on and it will release my key. I used to be able to start it after that but now it seems like it is becoming more and more difficult to start it. I have read about a loose fuse box under the hood, replacing battery, replacing ignition switch and resetting passcode. Im not sure where to start first. I do not have the extended warranty and am on a tight budget.
View 7 Replies