Mercury - Mariner :: 2005 - Noise That Increases At Around 60 - 65 Mph
I have a 2005 Mercury Mariner, 136K miles, 2.3L 4-cyl engine. I am experiencing a noise that is barely audible at 50mph, but increases at around 60-65mph. It is an intermittent "rrrrrr......rrrrrr.....rrrrrrr" (don't you hate people that describe things like this?) and I can sometimes feel a vibration on the gas pedal and also on the drivers side floorboard. And, maybe related, maybe not, every now and again it is a little "stickier" than it used to be when shifting into park.
View 2 RepliesMercury - Mariner :: 2005 - Creaking / Crunching Noise When Accelerate
I've been trying to chase down a creaking noise from what I think is the front passenger side for about a month now -- it happens when I accelerate and the weight of the car (2005 mercury mariner) shifts. It's mostly a creak but almost a knocking/crunching sound that seems to correspond to when I give it gas.
I recently got my sway bar links and tie rod ends replaced, so I could have sworn it was a bushing on the control arm. Spraying silicone grease doesn't do anything, and last night I noticed what I think is the same noise happen when I shift from park to drive.
Could this be a worn motor mount? I'd rather replace that on my own than have to bring it in and get a new control arm installed so I can get a realignment.
Mercury - Mariner :: 2005 - Something Electrical Is Draining Battery Causing Slow Starts?
Back in November I traded my sports car in for a more practical 2005 Mariner with 50K miles on it. I had noticed a somewhat delayed start during the test drive (at least compared to what I'm used to) and assumed it was the battery. Car drove great and I loved it otherwise so I made the purchase and went on my way. A couple weeks passed and I noticed the issue seemed to be getting worse and the engine took a couple more turns before firing up. I wasn't surprised as most battery issues surface when the cold weather kicks in. I took it to the dealer and they found a leaky battery and replaced it and again I went on my way. Unfortunately the issue was not resolved with the new battery. I didn't give it much thought thinking it was just the way the vehicle ran until the weather started getting progressively colder and my delayed start became even more prolonged. So back to the service department I go and wait patiently in the lobby with my book, hoping for good news. When they come back to me 2 hrs later they tell me that something is drawing too much power from my battery causing it to drain (alternator is fine) and they need to power everything down for a few hours and investigate the fuses in hopes of finding the culprit to the power drain. Later on I called for a progress check and they're still stumped and would like to keep the vehicle overnight and see if they can figure out the issue after it sits for a night since (as I relayed) the slow starts are primarily in the morning after the car has sat. From what I gathered, the evidence of drain "disappeared" after a while during their little power down session.
Consequently, I have them investigating 2 other issues and I'm wondering if any of them may be related. One- I am having issues depressing the shift button to get the vehicle out of park (also more of a problem in the morning during the first start). Two- on occasion my key sticks in the lock cylinder when I shut off the engine and try to pull the key out. I spent some time online researching all of the above and it seems that there could be some issue with the ignition switch or a bad solenoid somewhere in the circuit... then again, maybe not? The only other bits of info I can offer since owning the vehicle are that I was having some issue with the rear hatch door. I kept getting the "door ajar" light after using the back hatch.. but I'm pretty sure that was due to my own stupidity because the main door release and the top window release are right next to each other and I may have pressed the wrong one- slamming the back hatch hard took care of the light. The other thing is I followed the manual instructions and deactivated the seat belt alarms because I can't stand the seat belt reminder beeping at me when I forget my seatbelt.
Mercury - Transmissions - Mariner :: 2011 - Lurching At About 20 Mph
We purchased a CPO 2011 Mercury Mariner Premium in October 2013. The first time this incident occurred was when we had the car about 2 hours. What happens is after driving for a while at a high-rate (usually about 60mph or higher), I gradually slow down as I get off of the freeway and start heading towards our house. Once I get into the subdivision, as I am coaxing, the car will lurch when it is at about 20mph. This also happens if I am on the toll road and then slow down to pay the toll then somewhere around there or when I stop for my turn, it will lurch. I took the car back to the dealer within the first week and the mechanic and I drove the car for a while and of course, it didn't happen. He said there was no way for him to know what was happening unless it happened when he was in the car. I was actually put off because I asked if we should keep driving or take it back to the shop and he said "well, you know I don't get paid for test drives".
Anyway, they checked to see if there was an update on a module or something? He said there was (again, said he didn't know if it was related to what I was experiencing). It is still happening. We previously had a 2009 Ford Escape and got pretty good gas mileage. That car was totaled (fortunately no one was injured...my newest teen driver lol), and we had hoped to get as good gas mileage with this Mariner but no. Also, in December (2 months after we got the car) the "check engine" light came one. I scheduled it for service for the following Monday (it was Friday) and later that day, the car kept dying. We had to have it towed in. They repaired that problem and we hoped that it would solve this other issue, but it did not.
Mercury - Mariner :: 2009 - Faulty Gas Light Came On
I recently bought a 2009 Mercury Mariner 4wd Premier from a dealership (I upgraded from a 91 Ford Tempo...)
A few weeks ago I noticed that when I'd start my car the fuel gauge would be wrong (showing 1/4 of a tank when I had 3/4). The last straw happened when the gas light came on although I had more than half a tank. I took the car back to the dealership who verified and repaired the faulty fuel sensor. The mechanic told me it is not a common repair, yet just a couple weeks later I am finding that the problem is happening again.
What are the odds that I got a faulty replacement sensor or could it be a different issue? I will take it back to the dealership once the holiday weekend is over, but I'd like some other opinions. I know replacement parts can fail, but I know it isn't all that common.
Mercury - Mariner :: 2008 - Fairly Loud Chirping Sound
I have a 2008 Mariner that has just started making a fairly loud chirping noise from the from. It is not always there, sometimes when the car starts it doesn't always start for a minute or two.
View 3 RepliesJimmy :: 2001 - Strong Vibration When In 4WD / Front Drive Shaft?
2001 Jimmy 4wd, 115,000 miles; Recently I noticed a strong vibration when in 4WD, no vibration in 2wd. I found that the rear joint (at the transfer case) of the front drive shaft has play in it. I am assuming that this is the problem. It has the appearance of a CV joint. Is that joint rebuildable or do I need to replace the shaft?
View 1 RepliesMercury - Mariner :: 2010 - Passenger Side Brake Light Won't Turn Off
Last week, I noticed that my PS brake light was on, even when the car was off. I did not think anything of it, and figured I could get it fixed whenever I had some spare time.....then my battery died! Even with the batter dead, the light stayed on. I pulled numerous fuses, and none worked to turn it off, so I disconnected my battery (which did the trick). I have not jumped my car yet. I thought it might be the brake switch, but since it is just ONE light, and not both, am not sure that would be the problem. To note: I have a 2010 Mercury Mariner, 37k miles, and had a UHaul hitch installed about 3 years ago. DR brake light goes on when brakes are pressed.
View 2 RepliesMercury - Mariner :: ABS Light Came On / Dashboard Lights Dimmed To Black And Lost Electricity
Have a 2005 Mercury Mariner Premier, 108k miles, 3.0L engine. Was driving last week and the ABS light came on. Then slowly the dashboard lights dimmed to black and lost electricity. All this within a couple miles of driving. Limped home and tested the battery - dead. Recharged and tested the next morning - still fully charged. Put another known good battery in and drove about an hour out and on the way home same thing happened.
I suspect the alternator, but on testing, the alternator is pushing 14.3 volts on a good battery. My fear now is the tear down necessary to change the alternator if it is not actually bad. Anything else I should look for / test before I start pulling the alternator out? Any other tests of the alternator that I can do while it's still installed?
Mercury - Sable :: 2002 Stalling - Speedometer Needle Pulsating When Go From Park To Reverse Or Drive
It appears electrical. With it running and this first symptom usually guarantees that it will stall. You go from park to reverse or drive the speedometer needle will begin pulsating. I have notice if this is not happening it won't happen. Next standing still but in drive or reverse if you turn the heater, radio, lights or the AC pump kicks on. Boom the car stall and almost act like the key switch was turned off then back on. It also has happened while moving but it does not stall but all of the dash light pop on as if you just turn the car on.
View 3 RepliesAvalon 2005-12 :: Engine Knock - Strong Vibration Stinking Bad Sounds
This morning I went to start my avy and it ran poorly for about 30 sec (strong vibration stinking bad sounds) than started knocking loudly. It ran great when I parked it. I read that it could happen from poor quality gas, which I got gas the last time at a super run down gas station that still had rolling digits for the price I also used seafoam in the tank, could that be why? I took it to the dealer already which is about 30 miles after the car was warm it ran great.
View 2 RepliesGolf IV / Jetta IV :: 2005 - Jolts Forward When Shifting From Park To Drive And Occasionally From Reverse To Drive
Recently I've noticed that every time when shifting from park to drive and occasionally from reverse to drive in my 05 Golf GLS, I would have to remain off the gas for 3-4 seconds otherwise the car would jerk forward. If I press on the gas ever so slightly, the rpm would go up to around 1000 then jerk. Why this is happening?
View 2 RepliesCamry 2012+ :: Vibration At Idle Only When In Reverse Or Drive
A coworker has asked me to take a look at their 2013 Camry LE, 48,000 miles. It has a quite annoying vibration at idle and only when in reverse or drive. AC is not running this time of year, but does get worse if the compressor is turned on.
I'd like to think the trans and engine mounts are fine. It does not have any noticeable torque converter shudder. I have cleaned the throttle body, not that dirty, but not much improvement.
I suggested that he try different brands and grades of gas to see if matters improved at all - Shell 89 seems to be a slight improvement over what is normally used (just 87 from Costco, Sunoco, or Hess), but nothing substantial.
Spark plug change, decarbonizing top end?
Spark plugs look about like I'd expect an iridium plug to at these miles - no signs of oil burning, not tons of carbon, etc. I didn't get a real good look at the piston tops.
Passat (B6) :: Slight Vibration In Drive Or Reverse But Not In Neutral
I am experiencing a slight vibration with in drive or reverse but not when it is in neutral. I change the spark plugs and checked the PCV. I have the latest model already and I replace the gasket in the PVC. There is no errors in VAGCOM.. What could be causing that? Mounts???
View 4 RepliesPassat (B5) :: Vibration When In Drive Or Reverse And Stopped With Brake Applied
As outlined in this thread: [URL] .....
I had a recent misfire issue. Unfortunately the dealer has been unable to find the source. Since the original misfire I can feel the car vibrating when I am in drive or reverse and am stopped with the brake applied (ex - waiting at a stop light). It goes away when I drive and when I am in neutral. I realize there is SOME vibration noticeable in gear, possibly because of the way the engine is mounted. However, this seems different.
The tach stays at 750 rpm in idle (it may fluctuate a TINY bit but never goes over 800 at idle) as always. The vibration feels much like a vibration one would feel if a cell phone or pager were left on vibrate. This doesn't seem to be a rough idle where the car is "jittery" or "jerks", and, as mentioned, the rpm doesn't change.
I would think a bad coilpack or plug (plugs changed at 40K, Im now at 45k) would cause a misfire, and a CEL. I've looked into a throttle body cleaning and will do this, but I would think that would cause a rough idle as well. My understanding is that a MAF problem would be similar.
The only thing I can think of is a motor or tranny mount issue, but the car only has 45k miles and this problem was non existent until the misfire. Im almost certain it isn't related to having the car lowered recently.
Corolla / Matrix 2009-13 :: Low Idle Between 600 And 800 RPMs And Vibration In Drive Or Reverse
I think I resolved the idle issue on my 2009 Corolla S with 82,500 miles and Automatic Transmission.
Symptoms:
Idled at between 600 and 800 rpms
Annoying vibration in drive and reverse, no vibration in park or neutral
On hard stops, the engine felt like it was going to die
Turning on the a/c would cause the idle to increase to 1000 rpms and the vibration would go away.
At 82,500 miles, I cleaned the throttle body which was extremely dirty.
Process:
Disconnect the positive battery cable
Remove the top of the air box and flex duct going to the throttle body
Disconnect the two coolant lines going to the throttle body, make sure and have a few old bolts to plug the lines so you do not lose too much coolant
Remove the electrical connector to the throttle body
Remove the vacumn line to the valve cover
Remove 2 bolts and 2 nuts (10mm) securing the throttle body to the intake.
The throttle body does not have a gasket, it is an o-ring which should be fine.
Once you have the throttle body off of the engine, clean it thoroughly with Chemtool throttle body cleaner.
The inside of the throttle body and throttle plate should look like shiny milled aluminum. when done.
Spray chemtool into the two ports where the antifreeze lines were connected. If possible use compressed air to blow out these ports.
Clean the inside of the intake and the mesh screen where the throttle body bolts to the intake.
Reassemble, connect the battery, crank the engine and just let it idle for a good 10 minutes
The 2009 Corolla S DOES NOT have a serviceable IAC. It is riveted on to the throttle body. This is why it is important to spray the cleaner in the antifreeze ports in order to clean it. These ports are the antifreeze bypass ports.
Ford - Explorer :: 2005 - Vibration In Drive Train Above 62 Mph?
Before I take my dads truck to the mechanic. He noticed a "noise" when running highway speeds, which does not occur often for his truck..a beautiful 2005 Eddie Bauer Explorer with the 5.0 V8. I need this checked as I drag a boat to the Fl Keys from NJ in 3 weeks and the truck needs to be 100%. He just replaced the tires as his mechanic told him it was tire whine, which you hear and dont feel. The wheel bearings have been replaced in the last 2 years and they just did ball joints. I drove it up the highway tonight and felt it right at 62 mph..go faster it got more pronounced and you could feel it in the drivers seat...not vibration on the steering wheel..above 85 and it kind of smoothed out, drop below 62 and it goes away..makes no difference if you are in the gas or not..feels like something spinning out of balance....I ran it for 30 minutes at 75 and then pulled into a Lowes parking lot and drove one set of tires up onto a curb so I could fit under the truck..I started at the back and touched everything in the drivetrain for see if anything was hot..the rear differential was warm, the ujoints were not, the transfer case was warm as was the front differential, but none of the u joints or cv joints were warm... 2005 Explorer 100,000k miles...
View 12 RepliesElantra XD (2001-06) :: 2005 Doesn't Go Forward At All If Shift Into Reverse And Then Go Back Into Drive
I recently bought my '05 Elantra from a small dealership and I'm starting to see a problem with it. If I shift into reverse and then go back into drive, the car doesn't go forward at all. I have to mess with the gear shift a bit to get the car moving. I'm pretty sure it's a bad linkage. The dealership I bought it from said it desperately needed motor mounts when they got it so they replaced 2 of them. I'm sure the problems are related. I can't find any information on replacing it myself though.
View 1 RepliesFord Transmission :: 2005 F350 - 3 To 4 Seconds Delay When Trying To Engage Drive Or Reverse
Still having issues with the transmission on my 05 F350. I posted before that it would take a few seconds to go into drive or reverse. The fixes were to change filters and do hot flush. I had the dealer do a hot flush, and then I put about 1000 miles on it. That didn't seem to fix anything, so I went back in and asked for more info. They did not change the filters. I thought they did, but found out they did not after the fact, so I decided to change the filters myself.
The interior filter was easy to change. The fluid was clean, and the magnet had shavings on it but nothing that seemed extraordinary. The exterior filter is impossible to get off. I reviewed posts on here before trying, so first was the impact wrench, then the pipe wrench, then the pipe wrench with a block wedged in to keep the thing from bending, still no luck. The cast nut broke off well before the pipe wrench came out of the drawer. How to get that thing off. I read on here somewhere that no fluid goes through that until 180 degrees, is that correct?
Scanguage says it rarely goes over 160, except for last evening when I was stuck in traffic. It went to 187, with ECT at 208. During this period, traveling under 40 most of the time, the transmission was shifting erratically, to the point I wanted to pull over and allow it to cool down. But traffic broke free, speed went up, and temps went down. Shifting returned to normal, except when trying to engage drive or reverse. The 3-4 second delay persists at any temp, and there doesn't seem to be any slippage. Just delayed and sometimes hard engagements. I'm at a loss for whats wrong.