Hyundai - Sonata :: Cylinder Misfire / Power Loss While Going Up On Steep Hill
I am not a mechanic by any means, but have picked up a lot of stuff over the years. I drive a 2003 Hyundai Sonata with a 4 cylinder engine. Several days ago while going up a steep hill I lost power and my check engine light came on. This has happened before when my coil went bad so I figured it would be a breeze fixing it. I limped it home and ran the code. Sure enough it came back as cylinder 1 misfire. This vehicle uses 2 coils so I swapped them to try and get the problem to follow, but it did not. I have tried a new spark plug, new wires, and swapped injectors without success. There is still no activity on cylinder 1.
I ran a compression test. I get about 60 PSI on cylinder 1 and between 180-210 on 2-4. This would point to head gasket, so I am told. I do burn about a quart of oil every 500-1000 miles, but I do not seem to have any coolant leaking issues. I have not noticed any smoke from the tailpipe. The spark plugs were generally good looking, except for number 3 which had a hard white substance all over the electrode. There does not appear to be any oil in the coolant or coolant in the oil. This seems strange to me as everything I have read said that one of those would happen.
Is there anything else I should look into or is my engine toast?
Elantra XD (2001-06) :: 2005 Hyundai Runs Very Rough When Stopped At A Light And It Is In Gear
My daughters 2005 Hyundai Elantra has 77,000 miles om it. Just changed the wires and plugs, new brakes. Now, it runs very rough when stopped at a light and it is in gear. Now, when she has the AC running, and she stops at a stoplight, she has to put it in neutral or the engine will almost but not quite kill.
View 2 RepliesCamry :: 2005 LE 2.4 - Engine Runs Rough / Loud While Driving And Cylinder Misfiring
I bought a 2005 Camry LE 2.4 4 cylinder. It was rather loud while driving, but especially while accelerating. It had error code P0420 from the beginning. It had a completely broken torque strut which I eventually replaced. Afterward since it toned down the kicking from the engine, I was able to notice that I could feel and hear the engine kicking like a cylinder misfiring. The computer gave me error code P0353 (Ignition Coil C Primary/Secondary Circuit Malfunction) consistently, and only a couple of times gave me error code P0500 (Vehicle Speed Sensor Malfunction) which went away.
I swapped the ignition coil and spark plugs around but the error code would persist on the same cylinder. The spark plugs didn't look particularly worn but I'm not experienced on what bad plugs look like. The codes persisted still, but later on P0353 went away, and the obvious kicking stopped but it still ran with a lack of power and hesitating on acceleration along with a strong smell of fuel in the exhaust. I measured the resistance of each fuel injector and all measured the same. I removed and flushed each of them with cleaner, but same situation.
What do you think? I don't get the bad cylinder code anymore but something is clearly wrong. Bad fuel injector? Bad wiring harness? Bad compression or head gasket (maybe from the movement of the engine while the torque strut was bad)? Hopefully not the computer... And could the loud noise be related to this problem or is that probably just a cracked exhaust from when the torque strut was allowing engine movement?
Sonata NF (2006-10) :: Misfire On Cylinder 3 And 6 - Running Rough When Slow Down The Car
When I'm driving and get above 50-60 I will get the Check Engine Light. Check the codes It shows 6 ---300, 303, 306, 300, 303, 306. When I slow the car down it is running rough, almost like it has a miss.
I reset the computer while this is going on and the engine smooths out and it runs correctly until I keep my pedal down and then it kicks the exact same errors.
Here's strange part number one: Once I get down to about a gallon or two of gas in the car everything seems to run fine. I have plenty of power, no codes and the car runs fantastic!
Strange part number 2: Very occasionally When I get in the car in the morning to go to work, the car is a bit difficult to start. When it finally kicks over, it is immediately running rough. resetting the computer with the engine running does not seem to stop the rough running. If I turn off the engine and let the car set for a bit it will start and run fine, with the exception of the first problem mentioned in this thread. There is no code while it is running rough, but when the Light kicks on as per the first issue mentioned, I have an additional code -- 335. This car has been excellent up until the last few months when this issue developed.
Ford - Taurus :: 2005 Started Running Rough - CEL Came On / Cylinder 5 Misfire Detected
My wife's car suddenly started running rough. 2005 Taurus, 6 cyl, 3L, OHV, 83K miles. CEL came on and code came back as "P305 - cylinder 5 misfire detected". As a side comment, her tachometer has been fluctuating big of late as well.
View 2 RepliesHyundai Sonata :: 2005 - Rough Driving On Highway At Speeds 65 To 75 Mph
My sonata has started having issues on the highway at speeds ~65-75 mph. It will start vibrating, a little at first and gradually getting worse. As this happens my brake pedal seems to be more firm and touchy rather than soft and needing more pressure to stop. The vibration can be felt in the steering wheel and the floor as I drive. This has happened twice so far, with a gap of about a week in between incidents. What should I get checked out?
View 5 RepliesMazda - Mx-5 :: 1999 - Runs Rough Like Hitting On 3 Cylinder Now Won't Start?
I bought a '99 MX-5 in the fall with 100000 miles on it. Most of the time it runs fine. But about every two weeks when I go to start it it will run real rough like its only hitting on three cylinders then will eventually smooth out after anywhere from 5 seconds to 2 minutes. But today it wouldn't start at all. Finally started just fine after trying for 15 min. My mechanic changed the EGR valve but it hasn't worked. The check engine lite stays on all the time but when it starts rough the lite will flash.
View 3 RepliesV70 - Misfire :: 1998 GLT - Sporadically Runs Rough / Power Loss
THE FREQUENCY: This is a condition that has become progressively worse over the last six months. Initially it occurred once a week and now it is happening almost every day, lasts longer and is more acute.
THE SYMPTOMS: Initially and randomly, while driving at any speed, the car would begin to hesitate as if it might stall but did not- The hesitation was much like a shudder or power loss. At this time the check engine light would blink and stay on for a couple of days. This whole event would last less than a minute and the car would return to normal until the next one.
Now, six months later, it is occurring almost every day. At startup, at low speeds, at stop lights.... A LOT!
WHAT HAS BEEN DONE SO FAR: After frequent and unsuccessful visits to the Volvo Dealer all the plugs, the wires, the cap, and the rotor have been replaced with no luck.
The dealer says the code indicates a misfire on the #3 cylinder.
Ford Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesNissan - Maxima :: 1994 Runs Rough Occasionally / Cylinder Starts Missing
1994 Maxima SE 5 speed manual with 178k runs great when engine is cold, then a cylinder starts missing. Symptom is worse in low gears. Then, miles and miles without a miss. Replaced rear ignition coil and it seemed to fix the problem... for about 20 miles, then it started missing again. And stops missing… for miles.
View 2 RepliesFord F-150 - 1997-2003 :: 1999 4X4 - Intermittent Misfire / Runs Rough For About A Minute
I have a 99 F150 Lariat 4x4 with a 5.4, 150,000 mile on it. About 2 weeks ago I blew spark plug out on #2, and a friend who said he has heli-coiled a bunch of these tried to do mine and ruined the head. Anyway, I called a local engine shop and got another PI head, only I used my cam in it. Torqued it as per the book, etc... Mind you that the engine ran perfect before all this.
Got it back together with all new plugs, new exhaust manifold, and 2 new COP's. When I start it-it runs rough for about a min, then straightens back out to run perfect again, and after a few seconds you can hear a solenoid click, then it goes back to missing again. This goes on and on... I went through all the vacuum lines and checked them, checked the egr valve, put on a new IAC, new PVC, cleaned the MAF, and checked everything else with a DVM.
I took it out and drove it.... Runs good for a minute, then it goes back to missing, then back to smooth again. This just keeps going on and on. I noticed when I hear that click, it sounds like a mad rush of air being sucked in, but I cannot locate it. I ordered a new set of COP's to try next. I can understand if it just plain missed all the time, but this it intermittent. Also, the only code I can get is a too lean on bank 1, so I replaced the 90's and the pvc valve. Now no codes but still in and out of missing. It ran perfect before the new head.
Hyundai - Sonata :: 2003 - Ignition Woes - Cylinder 1 Misfiring
I am driving a 4 cylinder 2003 Hyundai Sonata just at 130000 miles. The other day on the trip back home the car started shaking violently and the check engine light came on. I ran the code and it led me to a cylinder 1 misfire. Today I replaced my spark plugs, and wires. The number 1 plug had some deposits on it, but nothing that should cause a misfire.
Now when the car is in idle there is a spark that jumps from the boot of one of the new wires to the grounding on the corresponding coil. I have never noticed this spark before changing the plugs and wires. It does this with either set of wires. I have a picture below where the spark is jumping from. The car has a noticeable drop in idle when it sparks. Do I need to look into getting some new coils?
Passat (B5) :: 1.8T - Rough Idle / CEL Came On / Misfire On Cylinder 4 And 2
So every once in a while I would start my car and get a rough idle but not too bad. I got a cel after a few times of this happening. I had a misfire on 1 and 4 and possible misfire on 2. It was ok for a a couple days. But during the last few days I'll start it up and it's fine. But then if I shut it off and restart it will have a rough idle again. Also today I got gas and then it rough idled and when I would shift or put it in neutral the rpm would stay up and drop slowly down. Like if I shifted gears I could almost do it without the rpms dropping at all. I've got 110k. ??
View 6 RepliesHyundai - Elantra :: 2002 - Rough Idle And Misfire When Hot / Intermittent Hesitation When Accelerating
2002 Hyundai Elantra GT 2.0L 140k miles
Symptoms:
- Intermittent rough idle when hot, slight shutter, surges between 700-800rmp
- Intermittent hesitation when accelerating, cylinder 2 misfire when hot and under load
- Misfires in all gears under load, mostly when under 2000rpm
- Code P0302 when scanned, no other codes
- Symptoms appeared suddenly, not gradually over time
What's been changed:
- Replaced spark plugs, little or no improvement. Old plugs looked worn, but generally in good shape with no significant deposits.
- Cleared code and swapped injectors between cylinders 1 and 2, after test drive P0302 code came back, so it seems that the injectors are good. If the injector were bad I would have expected the misfire to change from cylinder 2 to cylinder 1.
Inspection and Testing:
- Ignition System Testing
- Spark plug wires and primary coil are within specification.
- Secondary coil resistance is high on both packs. Could this be causing a problem with just cylinder 2? Is it worth replacing?
Spark Plug Wires: Specification: 5.6 Kohm/meter +- 20%Cylinder 1: 2.49 Kohm (Longest)Cylinder 2: 2.03 KohmCylinder 3: 1.64 KohmCylinder 4:1.36 Kohm (Shortest)
Primary Coil: Specification : 0.58ohms +- 10%Actual: .6 and .6
Secondary Coil: Specification: 12.2 Kohms +- 15%
Actual (Cold): 16.03K for Cylinder 2-3 pack and 15.94K for Cylinder 1-4 pack
Actual (Hot): 18.54K for Cylinder 2-3 pack and 18.44K for Cylinder 1-4 pack
Air/Fuel System Testing:Fuel system seems to check out. I do not believe the problem is fuel related. There are no obvious cracks or leaks on the intake manifold. A good spray of Carb cleaner all around the manifold causes no change in idle. I might try propane later. No obvious vacuum leaks.
Fuel Injector: Specification: 13.1-14.5 ohms
Actual: Cyl 1: 14.9, Cyl 2: 15.3, Cyl 3: 15.3, Cyl 4: 15.7
Compression Testing:Compression is not great, but within specification. Could the slightly lower compression in Cylinders 2 and 3 indicate a head gasket leak between those cylinders? Could this cause a misfire in Cylinder 2?
Dry Compression: Specification: 145-218psi, <15psi between cylinders
Actual: Cyl 1: 165, Cyl 2: 155, Cyl 3: 155, Cyl 4: 160
Oil/Coolant/Tailpipe:
- Oil looks normal, not brown or milky
- Coolant looks normal and is full, no signs of leaking (coolant has not been changed in a very long time, could a coolant flush work?)
- Exhaust looks and smells normal from tailpipe.
Sticking valve? How would I check this? Bad sensor somewhere? Doesn't a bad sensor usually throw a code?
Passat (B6) :: Engine Running Rough And CEL On - Misfire On Cylinder 2 And 4
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
Passat (B5) :: 2004 1.8t Running Rough With CEL On - Misfire On Cylinder 1
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 RepliesPrius (2004-09) :: Misfire On Cylinder 2 And 4 - Car Severely Idle Rough
I own a 2007 prius, it has about 320,000 miles. It has recently been diagnosed with a #2 and #4 cylinder misfire. The car severely idles rough, but when getting in the gas it goes away. I have replaced the spark plugs, the old plugs were very white(lean), replaced fuel injectors, used fuel injector cleaner. I've sprayed carb cleaner around the intake to see if I might a leak--no leak. The motor uses about a quart of oil every 1,000 miles since about 100,000 miles. I'm just guessing, could it simply be low compression causing this? I pulled the new spark plugs after about 5,000 miles and they where white also.
View 9 RepliesLexus GS 2006-11 :: GS300 Rough Idle / Misfire On Cylinder 2
I bought a 2005 3rd gen about 8 weeks ago and I love it except for one problem, a really bad idle/vibration through the cabin when cold starting, it improves when the engine is warm but is still noticeable.
It went back to the dealer where I got it and they gave it a full service, new plugs, oils and filters and replaced the transmission oil too after the check vsc and engine management lights came on.
The codes pulled showed a misfire on cylinder 2, the dealer said the service would cure all and sure enough no more vsc lights but the rough idle and vibration are persistent.
The car has only 78000 miles and I'm pretty certain a Lexus isn't supposed to behave like this.
Accent MC (2006-11) :: CEL Flashing / Rough Idle - Cylinder 1 Misfire
I did not get the specific cel code but its what the guy told me at autozone.
Long story short. Washed engine, let sit for about 30 mins. Car started with flashing CEL and was "puttering" and very rough idle. Drove home took intake off and replace with stock, took spark plugs out and they were not wet. Then let it sit for about 15 mins. Started just fine. No CEL at all.
The accent saved the CEL and the guy told me that Cylinder 1 had a misfire.
My question is, should I do anything now even though the car seems to be running ok?