Honda - Odyssey :: 2001 - Car Goes Into High RPMs (about 3000) Before It Seems To Drop Into Gear
I had my Honda Odyssey transmission replaced 2 years ago. The past few months, in the first mile that I drive the car on streets in our neighborhood, the car goes into high RPMs (about 3000) before it seems to drop into gear. It does this 2 or 3 times then works fine after that. The "Check engine" light is now on all the time. Sometimes, the car does one other weird thing--the high RPMs end with the drive/D4 light flashing on and off like a blinker (even if I change gears to D3. When this happens, if I turn the ignition off it comes back on and seems to function fine. I have had it back to the shop that did the work about 4-5 times to get it right. I like the guys but each time they return it to me, the problem remains. I took a 2000 mile trip with it and with the exception of this persistent problem, the van worked fine.
View 2 RepliesHonda Accord :: 2001 V6 Idle Revving / Jumping Between 1000 And 3000 RPMs
My car is a 2001 honda accord v6. It sat for 3 winter months. When I go to turn it on in the morning, the car will rev while idling. Jumping between 1000 and 3000 rpms. Why this might be happening?
View 3 RepliesHonda - Accord :: 1983 - When Rolling To Or At Stop RPMs Drop And Stalls
I have a 1983 Honda Accord (manual with nearly 200,000 miles) when rolling to a stop or at a stop rpms drop below 1000 and it stalls out. I can start it back up without hesitation.No hesitation at initial startup or after sitting short or long time, it idles while in park rpms about 1000.When I feel the engine about to stall while rolling to a stop or at stop, if I put my left foot on the brake pedal, slightly step on the gas pedal with my right foot it prevents the engine from stalling. At stop if I put in park, rpms raise and don’t need to give it gas.
I'm unable [& unqualified] to work on my car. Given I drive only about 1,000 mi year; my alternate form of transportation is a bus or kindness of friends, I’m on a limited income, cannot afford to buy/ spend more than 2,000 -- my question if 2-foId, 1. is it possible that something it is nothing major and worth repairing/replacing (ex. air control/idle air bypass valve, a dirty throttle body or even carburetor)?2. Or, as discussed with one mechanic, since the car is 33 years old, during or soon after repair other problems (dried out vacuum hoses or major) will follow. Plus, parts can be difficult if not impossible to replace as a I spoke to mechanic pointed out.Given the car’s age is it worth repairing?
Passat (B6) :: Rpms Just Fall Than Car Shuts Down
It showed up when the car wouldnt start. It would start but the rpms would just fall then shuts down. And now I have been having issues with the car not starting. At times it would start on the first try and others i have literally tried over 10 times and it wouldnt start... eventually it always starts but i dont want to get to the point where i get stranded.
View 8 RepliesFord - Escape :: Rough Idle And Way Below 500 RPMs To The Point Where It Almost Stalls
I have a 2001 Ford Escape, and when I start it for the first time of the day, it idles really rough, and way below 500RPMs (to the point where it almost stalls). After about 10 minutes, when the car is all warmed up, it runs smoothly, as if there was nothing wrong with it. The only conclusion I can draw is that it is temperature related, but I can't figure out exactly what is causing the issue. This happens on the driest or wettest of days, so moisture doesn't seem to be an issue.
View 2 RepliesFord F-150 (2004-2008) :: Rough Idle / Bad Gas Mileage / Stalls Out / RPMs Jumps Around
I bought an 04 f150 super crew cab with the 5.4L triton in it 3 years ago with 50k on it from my great uncle who was the original owner. It's had a tick to it since he had it but the dealership told him they couldn't find anything wrong with it and to get use to the noise. It's ran pretty good up until last couple months where it's been running really rough and not doing the best. It's still hasn't been all the time but more intermittent and comes and goes, but when it's running bad the rpm drops down to about 200 and my motor sounds blown.
When that's happening I could put in neutral and rev it up and it would go back to normal for a bit, but now it's all the time and stalls out even at 70 on the hwy. The codes it throws are, p1000- monitor checks not complete-more driving required, p0345- camshaft pos sens circ error(bank 2), p0022- A camshaft pos timing-over retarded bank 2. Things I have tried-changed all 8 plugs, added K&N air intake, replaced both cam sensors, replaced fuel pump driver module (due to corrosion). Tonight I'm going to clean the throttle body, mas air flow sensor, change fuel filter.
Suspension - Mercedes-benz - S-class :: 1987 - Rough Idle And Stalls / RPMs Drop
Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....
View 19 RepliesSanta FE SM (2001-06) :: RPMs Fluctuate And Car Stalls At Stop
I have a 2001 Hyundai Santa Fe LX with 214,000 miles on it. In general, I am having two problems which are most likely related. I would like to get opinions on what is causing the problems, how to fix the problems, and what the cost might be for the fix. This is an older car and I don't want to bring it to a mechanic to just do searching.
1. RPMs fluctuate quickly at slower speeds in town stop and go traffic and while parking in Drive or Reverse. Fluctuation can be between 1000 to 2000 and 3000 RPMs back and forth.
2. Car stalls while sitting at stops when in Drive. When car stalls, RPMs have suddenly decreased to 0 (zero).
3. RPMs fluctuating and car stalling typically occur after I have made my first stop and have turned off the car.
There is also a Check Engine Light Code: P0304, Cylinder 4 Misfire Detected. I changed the vehicle speed sensor a few months ago.
Here are the details of what has been happening, when it happens, and what I have tried.
- When RPMs fluctuate, the car slowly accelerates and slows down and I can hear revving high and low. This happens when the RPMS fluctuate just a few RPMs around 1000 and when the RPMs are fluctuating up to higher RPMs.
- After the car has been driven for about 45 minutes and car is at slower speeds, RPMs will fall to zero while at stop and in Drive, and the RPM fluctuation will begin.
- RPMs jump to 2000 or 3000 and stay there but do not fluctuate when car is put in Park and Neutral.
- When car is in Park and at 2000 or 3000 RPMs, car takes a few extra seconds to turn off.
- Car accelerates without pressing gas pedal and will accelerate up to 40 mph.
- Car will sometimes lurch at slower speeds of 15, 25, and 35 mph when RPMs are fluctuating or when the gas pedal is pressed.
- When RPMs are fluctuating and at 1000 or higher and I am pressing the brake to slow down, the car fights in Drive and in Reverse.
- RPM fluctuation does not occur at interstate speeds.
- A couple days ago, when I was at interstate speeds of 60 to 75 mph and pressed the gas pedal, the car would stutter and jerk.
- RPM fluctuation and stalling primarily do not occur when the car is started at the beginning of the day or when the car has been off for several hours.
- Twice In the last week the RPM fluctuation and stalling occurred even after car was not started for several hours and after only about 5 to 10 minutes of driving in town stop and go traffic.
- Sometimes car stalls when I'm at a stop and slightly press the gas pedal to start driving.
- There are times in town traffic when the car is operating normally and is at 750 RPMs at stop, then the RPMs suddenly decreased from 750 to 0 (zero) and the car stalls.
- From Neutral, sometimes when I simultaneously put the car in Drive and press the gas pedal either by feathering or forcefully pressing pedal 3/4 to the floor, the car would have a delayed reaction to accelerate but would not shut off.
- After car has stalled, if I try to start it right away, the car cranks but does not start for about 5 minutes.
- The time between stalling and being able to get the car to turn back on has increased over time from starting up at first crank to not starting for 5 minutes.
- If I let the car sit for 3 to 5 minutes after it has stalled, the car starts up but takes a couple seconds to start while pumping the gas pedal.
- Issues have been happening since November but are getting more frequent.
- Stalling is happening more frequently and within minutes of each other.
Passat (B5) :: Engine RPMs Climb Slightly Then Fall And Repeat When Cold
I just turned on my car to move it out of the drive way and i noticed it starts rising when cold probably like 25-50 rpm then goes down, then back, and so on. i never noticed this before. is it a cold start assist or something like that ? i dont believe it does it when cold ( never noticed )...
View 11 RepliesDodge - Durango :: 2003 - Stalling / RPMs Would Fall Off Drastically When Come To A Stop
2003 Dodge Durango 4wd, 4.7 liter, 130,000 miles ... I'm having a problem with stalling. First started about 3 months ago, when I would come to a stop, the rpm's would fall off drastically, but would rebound right away. About a week later, it would actually stall, but I could start it without a problem. Took it to a local shop where they said my cam sensor needed replacement. That was done and it ran good for about 2 weeks when the same thing started again.
Took it back to the same shop and they told me that the cam sensor had gone bad or the sensor that had been put in was faulty. They replaced it at no charge to me, but they said that the crank sensor needed to be flashed and that had to be done by the dealer. So off to the dealer I went, and they told me that the crank sensor needed to be replaced not flashed. I had them do that and it ran good for about 2 weeks again and now it's starting to stall again.
Explorer :: 2001 Ford - RPMs Drop To About 4 To 500 And It Stalls Out In Reverse Only
I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.
View 4 RepliesElantra XD (2001-06) :: Stalls While Driving Frequently / RPMs Drop For A Split Second
06 Elantra Limited, 96,xxx miles. When I'm idling at a light or something, the Rpms drop for a split second, almost to the point of stalling, but recovers. Happens in a split second. Does the same thing even when driving, but does it more frequently when idling. It even does that when I first put my foot on the throttle to accelerate from a red light.
I've cleaned the throttle body but it still does it. I've taken it to 3auto parts stores. One said that battery was bad. The other said the battery is fine but alternator is producing low. The last said both are fine.
Honda - Cr-v :: 2000 Stalls When Engine Is Cold And Shift Into Gear
My 2000 Honda CRV starts when cold, however I must continue to give it gas and it will die when I shift into Reverse or Drive. If I rev the engine, I can keep it running and it will run OK once warmed up. When I get it going, the engine will stall if I attempt to let it idle. All problems resolve themselves once the engine is warm. Several mechanics have seen the problem, but cannot determine a solution other than to let the engine warm up. I live in Boston and the combination of having to work my way out of a parking space and the enginge continously stalling when I shift into R or D is making life difficult?
View 5 RepliesFord Super Duty (1999-2016) :: Rough Idle And Stalls But Runs Fine At Higher RPMs - No Brakes
Let me start with I have a 2003 f250 5.4. The motor blew on my truck and I had a 100k motor dropped in it. I've put new spark plugs, ohmd out the coils. I tried both sets of injectors. cat delete and new fuel pump. It has rough idle and stalls but runs fine at higher rpms. Also has basically no brakes. I am thinking vacuum but I've check all the lines. No codes either!! also cleaned throttle body.
View 4 RepliesFord F-150 (2004-2008) :: Low Idle When Put In Gear And Sometimes Stalls
I changed the plugs on my 2004 F-150 FX4 with 165,000 miles. Immediately afterwards I experienced a low idle problem. After engine warms up, idle is at about 400 rpm in nuetral or park. When I put in gear it drops to 200 rpm and sometimes stalls. Ford analyzer says misfire #8 cylinder. I swapped coils with #7 and reset fault. #8 cylinder misfire came back. So next I put new plug in #8 thinking the plug was bad. Still have low idle problem. What I should try next?
View 3 RepliesCivic - Honda :: 1989 RPMs Will Never Get Above 2000 In 1st And 2nd Gear
RPM's will not get above 2000, in 1st and 2nd gear. No power....
View 16 RepliesCivic - Honda :: 1998 - RPMs Fluctuate At Idle
My 1998 Honda Civic DX's RPMs are fluctuating during idle. I start the car and it is normal for about two seconds. I am assuming around 800 rpms (I don't have a tachometer). Then it jumps drastically higher, then lower, then higher, etc. Earlier tonight I replaced the throttle body gasket, replaced the spark plug wires, and cleaned the fuel injector cleaners. I took off several things in the process. I think the problem originates from taking apart the throttle body - not the other replaced parts. I have a manual 2-door 1998 Honda Civic DX with a 1.6L engine (D16Y7 engine to be exact).
View 15 RepliesNissan - 350z :: 2004 - Stalls At Idle - Rides Rough When In Gear
I was driving on the highway today, and when I turned onto the exit ramp and put the car in neutral I noticed my gear shifter shaking back and forth pretty violently. I looked down at the tachometer and saw it idling at less than 200 rpm's in neutral. I got to the light and my car stalled. I turned it back on and I had to feather the gas pedal just to keep the car running. I was able to make it to my local car mechanic with one foot on the gas pedal and my hand on the e-brake. It runs a little rough when in gear but at least it keeps the rpm's up enough to stay running. The check engine light never came on. My guy said that he didn't have the appropriate diagnostic machine, but he's afraid I might need a new throttle body and a new computer which may cost 1000's of dollars. I think the code he told me that he found was P0506. He sent me to a guy that deals only with Japanese cars, but they won't be able to look at my car until Monday.
Any thoughts? Hopefully something that doesn't cost 1000's of dollars. And if I replace the throttle body does that mean I have to replace the computer too? Is there something that I did or that I didn't do that I should have been doing that could have caused this to break?
Ford F-150 - 1997-2003 :: 1998 V6 - Loping At Idle / Almost Stalls While In Gear
I have a 98 F150, 4.2 V-6, 183,000 miles.. Lately, she's been loping at idle. Especially while in gear... almost stalls. Once revved up, everything seems normal. Still goes up hills fine if I get on the gas. The light was on, and I got codes for lean condition on both banks.. (P0174, P0175).
I already cleaned all the sensors in front of the intake.
The MAF was real dirty, and the IAC was full of soot too.
They both cleaned up nicely, but it didn't work.
I borrowed a fuel pressure gauge yesterday, and it showed 12 psi with the "key on, engine off".
It showed 29-30 @ idle, and only went up to 35 when I revved it a little.
The guy at the store said the range is supposed to be "30-45 psi with the ignition on", but I'm not sure if that means engine running or not..?
Either way, it looks like the pressure is on the low side, so I'm going to change the fuel filter next (and hope for the best).
If the fuel filter doesn't fix it, what should I go after next? And, is there a way to test the fuel pressure regulator before buying a new one?