Honda Accord :: 2000 V6 Idling / RPMs Drop On Startup

I've had my 2000 Honda Accord V6 for about 3 years now and have had an idling issue pretty much since I purchased it. After driving for at least 50+ miles, and if its hot out it can easily have this issue as well, and leaving the car be for around 15 to 30 minutes, on start up the car drops RPMs immediately and dies. Multiple tries and it will do the exact same thing. Recently I found out a trick to make it work correctly which is revving the engine to 2000RPM for about 3-4 minutes, slowly dropping it down to 1500 RMP for around the same 3-4 minutes and finally down to 1000 RPM for an additional 3-4 minutes and letting off the gas. Usually after doing this the engine idles fine, car drives great. However, it must be noted that on Summer days with temperatures in the 85+ range, if I'm climbing (going up a hill for a long distance) the car might bog down on me, will not go above 50MPH and I have to pull off the side of the road for 45+ minutes before the car will run correctly again. This has happened about 3 or 4 times in the 3 years I've owned the car.

I would rather not have to rev the engine in hopes this fixes the issue each time so I'm wondering what could be the cause in the first place? I've replaced so many things including spark plugs, ignition coils, battery, idle air control valve, gasket, fuel pump, fuel pump relay and on. I gas the car up with Chevron gasoline, I've dumped in I don't know how many different fuel injector cleaners and have also tried Heet as well as Sea Foam cleaner. I've also had the car checked for vacuum leaks.

I've asked multiple mechanics if this could possibly be a vapor lock issue, but they all turn that idea down. They tell me that since the car is fuel injected this can't be the issue..but, I don't know, could it be the issue?

View 9 Replies

Honda - Accord :: 1998 Not Starting - When Turn A Corner RPMs Drop Like Running Out Of Gas

My 1998 Honda accord coupe 3.0 has 225 k miles has a new sending unit, fuel pump, main relay, ignition switch, and spark plugs. I cannot find the source of why my car will not start I replaced these things on my car due to car didn't want start. Then it was fine every time I would turn a corner or drive it rpms would drop like I was running out of gas then it would die now it will not start.

I have checked all fuses. I have read in forums that this could take a lot of money to fix only because no one knows the source of why its not starting. I am a disabled female that is just trying too have a running vehicle and can't figure out why it won't start. It has a new battery but won't hold a charge. Had charged it from my friends car for 25 minutes it gave it enough juice to put it in neutral and push it in the driveway with another car.

View 19 Replies

Honda - Accord :: 1998 - Random Power Loss And RPMs Drop Low Enough For The Engine To Stall

I have a 1998 Accord, 4-cylinder VTEC standard transmission, 226,000 miles. Last fall I first experienced a problem with the car where within 5-10 minutes of starting the engine and driving, the engine seems to lose power/fuel and RPMs act as if they'll drop low enough for the engine to stall. If I take my foot off the accelerator, and reapply, the engine seems to gain power again.

Also, if I open the accelerator to full while the problem is occurring, it can occasionally "push through" and gain power again. Similar things will happen while stopped. In neutral, RPMs fall low and suddenly jump back up and then settle into normal idle. The problem never persists longer than 10 minutes within starting the car.

I took my car into a local shop that came recommended by a friend. They investigated a "check engine" light that didn't explain the problem and were never able to recreate the condition themselves. They replaced a few parts but lost the work order so I don't even know what they changed, but the problem seemed to have solved itself for a while. Recently it started up again and I would love to sort it out.

View 2 Replies

Stalling - Honda - Accord :: Stalls Unexpectedly When Coming To A Stop Or Slowing Down

2002 Honda Accord, 4 cyl., will stall unexpectedly when coming to a stop or slowing down. It will start to shake and hesitate as one is slowing down from 35+ mph, then will stall at the stop. Has some trouble restarting, but when it does, everything seems to be fine. No codes are left, and my mechanic suspects dirt or something similar is contacting the fuel injector(s) on a sporadic basis. I did replace the spark plugs as they were due at the time this first showed up, but it has happened twice since in a 3 month period.

View 3 Replies

Civic - Honda :: 1983 - Grinding / Squeaking Accompanied With 5mpg Drop

There is a grinding/squeaking noise coming from what sounds like the front driver side wheel area. It is not constant... the interval between each occurrence is relative to vehicle speed. When moving slowly, like in a neighborhood, the gap is about a ½ second. The gap lessens til I hit ±65mph, when each occurrence runs into the next and the sound is pretty constant. The 10 fill-ups before this started I averaged 42.3mpg, my last 2 fill-ups average to 37.6mpg...Oh, there is no audible sound when the car is on a lift...

At first I thought a dragging brake but there is no change in the sound when the breaks are applied...I bled the lines anyway...no change.I thought CV joint, but, from what I've read, the tell-tell clicking and worsening under heavy cornering is not present.Maybe a wheel bearing? I've done the simple bearing test of trying to wiggle the wheel left-to-right & top-to-bottom...no movement.

By the way, this is a manual transmission and the sound is present whether in gear or in neutral or coasting with clutch depressed.

One more thing I should mention, and this might be important... my first poor mpg result coincided with me disintegrating a rod bearing...(low oil) I did replace the bearing with the appropriate size. I measured the crank journal with a micrometer and it still seemed to be right at the factory specs. There were no scores or gouges in the journal. (As soon as I heard the loud ticking associated with a bad rod bearing I shut the car off and pushed it to work where we have a lift. Luckily it was only about a mile and was pretty flat...it doesn't hurt that the car only weighs 1,800 lbs. either.) Anyway, I reassembled the bottom end, torqued the rod cap according to the factory service manual, torqued the oil pump and the oil pan, added new oil and started it up. It ran, and still run, nice and smooth.

View 9 Replies

Ford F-150 - 1997-2003 :: Runs Rough And Stalls When Stop Or Rolling To A Stop It Would Die

I am having trouble with my 1998 F-150...XLT Triton? I bought the wrong motor for it and installed it, turn out it's a 1999 Windsor 5.4

Problem is that it runs rough and stalls when I stop or rolling to a stop it would die.... It seems ok while cold, but when driven for 20 minutes or more it does it.

I have used original 4.6 harness as well as original spark plug coils and only replaced throttle body, oil filter holder thingy mount, exhaust manifolds are from 4.6.

When the throtle body was on the 4.6 I didn't have when the motor ran. Only misfire due to intake manifold leaking into the 3rd cylinder spark plug.(I thought it was a bad head gasket and changed in....installed the timing chain wrong and messed up the whole motor)

Also I broke a rear brake line and now it only has front brakes and smells like fried transmission oil.. This is my first truck and first truck accidental engine swap. Also the 5.4 Intake manifold is missing 2 coolant sensors and it's giving me the P0118 ECT Sensor Circuit High input...

View 2 Replies

Caravan/Voyager :: 96 Plymouth 3.3L Suddenly Stalls - RPMs Drop To 0

1st problem is shifting from 1st to 2nd and sometimes from 2nd to 3rd though, 2nd to 3rd is not as bad as from 1st to 2nd. It stumbles and gets really bad if I don't let up on the gas. After the initial shudder it will go into 2nd just fine. I also have to gun the gas a little bit when I first start the car, or it will just sit there and idle and never go into gear.

2nd and more annoying is that it stalls after driving around a bit. It happens on freeway or city. It doesn't stutter or anything the rpm's drop to 0 and it just stalls and won't start up for a 5 - 10 minutes or so.

Codes pulled are P0731, & P0736. The transmission was replaced about 2 years ago with a refurbished one. Could it be going out again already? The guy at Autozone suggested replacing the TSS (Transmission Speed Sensor?) to see if that was the problem. I have not done this yet, but plan to.

View 3 Replies

Explorer :: 2001 Ford - RPMs Drop To About 4 To 500 And It Stalls Out In Reverse Only

I own a 2001 Ford Explorer and have had the regular wear and tear but this problem has me stumped. A few months back I had to change the auto body gasket because the truck would not go into gear. After doing this the truck ran fine, I also changed the tranny fuild and filter. The other day i went to back up into the garage and the truck stalled and died out. it started right back up and it runs fine in all other gears. (P,N, D, 1,2, 4x4 high and low) and the over drive is working fine. when the truck is cool and hasn't ran in a while i can start it and the rpms stay at about 1000 th 1200 and the reverse works great. Now when the eng. heats up to normal and i put in in reverse the rpms drop to about 4 to 500 and it stalls out and dies. I have cleaned the mass air flow sensor, the throttle body, and the IAC valve but still dying out. Im thinking it may be a vaccume leak or the IAC is bad and cleaning just wont do the trick. I have also read that it may be the back up light wiring that hooks to the tranny may be shorted out.

View 4 Replies

Camry :: 2003 V6 Stalls At Stops Randomly / RPMs Drop And Then It Revs Up

I have a 2003 Camry 3.0l v6. Stalls at lights random.

Currently the car stalls at stops but this doesn't happen all the time it can go a month in between the problem occurring its very random. While sitting at a light the rpms drop and then it revs up and cycles like that for quite a while. This will also occur while cruising at a low speed while I'm just coasting the rpms will go up and down. I can compensate while stopped by power braking and keeping it at its normal idling rpm. I have no check engine lights and can't seem to determine what would be causing this issue.

View 5 Replies

Elantra XD (2001-06) :: Stalls While Driving Frequently / RPMs Drop For A Split Second

06 Elantra Limited, 96,xxx miles. When I'm idling at a light or something, the Rpms drop for a split second, almost to the point of stalling, but recovers. Happens in a split second. Does the same thing even when driving, but does it more frequently when idling. It even does that when I first put my foot on the throttle to accelerate from a red light.

I've cleaned the throttle body but it still does it. I've taken it to 3auto parts stores. One said that battery was bad. The other said the battery is fine but alternator is producing low. The last said both are fine.

View 11 Replies

Lumina :: 1992 - Stalls Intermittently And No Start / RPMs Drop Rapidly

I purchased a 92 Lumina Euro with a 3.1 and 101,400 miles on it a little over two weeks ago. It has been having problems since I got it.

It stalls intermittently, typically after I drive to work, shut it off for two hours, and then start it to go to my next client(home health aid) sometimes it stalls right after starting it then, and/or sometimes when put in reverse and/or drive and occasionally at stops signs after the aforementioned problems occur. It has also stalled out twice after highway driving after the car is shut off and started shortly afterwards, for instance, when I ran into a tobacco store for some cigs.. After the problem occurs it usually drives ok if I continue to drive it awhile even if I shut it off for a short time and restart.. I added some fuel injector cleaner when I filled the tank but it didn't work.

After about a week of the stalling issues the car refused to start after dying and didn't start for two or three days. As I was unable to get an answer from the dealer my step-father, who went with me when I bought the car, called him and he said if I could get the car there he would fix it. So I borrowed a bundle to have it towed the 25 miles or so to the small town car lot.

His mechanic supposedly fixed it by replacing the TPS and the dealer informed me that they had cleaned the throttle body before I bought it and apparently the TPS needed replaced to. However the issues again started after one day of it running fine. I tired to get a hold of this guy again and again I get the voice mail and no return call so as soon as I got off work I drove it over there and again he said he would fix it. He had it for three days and I again tried to get a hold of him without success and he again answered the phone for my step-dad and told him they had ordered some kind of module that would be in Monday. So Wednesday he calls me and tells me that they didn't replace this module because when they took it out it tested good five times but they noticed some gunk build up at the contacts of the wires that hook to the module and now the car was fixed. Why did they order the part before testing??? This doesn't make sense so it throws doubt on what the man said. I went to get the car and when I got back to my town and went to get those cigs it died twice after restart and put into reverse. That was two days ago and it has been dying once or twice each day since then although it is somewhat better than before as it isn't taking as long for the idle to even out at sufficient rpms after I throttle it at idle or drive awhile. BUT now it seems to be sucking the gas hard and I am wondering if this guy just did some jerry-rigging because he sure isn't fixing it.

A few more details. The rpms drop rapidly when this occurs, it has a couple of times had a rough idle at the same time but more often the rpms drop and it dies.Sometimes if I use the throttle and keep it up around 1000 rpms for a short time it won't die. I have smelt a burnt smell a couple times when I shut the car off, like electric burnt, not oil burnt or stinky exhaust. Lets see, I felt a very brief loss of power feeling when driving on the highway on two different occasions, so brief that it was barely discernable. It runs over the halfway point on the temp gauge after driving awhile in town, seems a little hot to me but I read these cars don't kick on the fan till 220. Sometimes the rpm bobs a little up and down at idle and slow speeds and once the battery power dropped and popped right back up when it was idling funny and when it had that no start an acquaintance tested it by putting a screwdriver in a plug wire and pointing it towards the engine as I cranked it and he said it had no spark and it did crank every time I tried to start it during the no-start condition. It has also done a bit of surging from time to time when the prob happens. The car is recovering from the stall condition quicker than it did before since this last "fix" but still stalling.

View 5 Replies

Suspension - Mercedes-benz - S-class :: 1987 - Rough Idle And Stalls / RPMs Drop

Hot or cold car always starts,Idles perfect , then RPM drops, Idles rough and stalls. Econometer moves to Red area.car will easily restart and drives well,it also idles well. Once engine is shut down, even for a short while, It does the same thing again. Car is used for short trips. Ambient Temperature 80 degrees. Once running car is perfect at all speeds and idles smoothly. Hero 1987 MB 560 sel ....

View 19 Replies

Ford 7.3L Power Stroke (1999-2003) :: After Start Up RPMs Drop - Stalls Out Then Idles Rough?

2003 7.3 excursion.. The truck starts every time revs up and idles about 3 seconds then the rpms drop and it tries to stall out catches itself then revs backup and idles rough similar to if you have got air in the fuel lines from changing the fuel filter.. About 1 in five times the truck will stall out and it starts and immediately and idles rough but the rpms and everything runs at speed and rpms don't drop again! This is a reman engine/transmission recently installed.. The mechanic who installed it was unable to figure the problem out.

View 6 Replies

Honda - Accord :: 1996 LX Wouldn't Rev Up To About 200 Max Out And Then Drop

*1996 Honda accord LX. 255, 498 miles.

Well, a couple months ago I think I overdid it on the seafoam spray in my PCV valve. It was kind of hell to start, I put some starter fluid in there and it finally cranked right over. I thought that was the end of it, but now I'm thinking it was a coincidence.

Today I went to start my car and it wouldn't rev up to about 200 max out and then drop. If I stopped cranking it with the key, it would die. Well I put starter fluid in the car and it still wouldn't go! I had to crank it for about 12 seconds to get it to turn over, normally when the engine catches(My foots full on the throttle when it won't start) it soars to 2.5k RPMs pretty quick. I started it later at school and it acted like it wanted to give me trouble, but a second past and it turned over and started running. I pull into the driveway today and I see my oil light flickering a little bit. First time I've ever seen it, a little worried! I turn the back on, starts up right away, to see if the oil light comes back on and nothing. But still worried.

I also got a coolant leak somewhere that I haven't been to diligent about finding. I don't see coolant anywhere on the driveway, my cars drinking coolant and I don't know where it's going. I checked it the other day and the reservoir tank was bone dry and so was the top of the radiator. I just added some UV dye to see where it's going, UV flashlight is on the way.

View 19 Replies

Honda - Odyssey :: 2005 - Drop In RPMs At Approximately 30 MPH

I have a '05 Honda odyssey that has recently started showing drop in rpms at approx 30MPH. At that speed, I see that RPM suddenly drops from 2500 to 2000, pressing on gas really hard, triggers downshifting of gears and everything comes back to normal. I suspect some issues with how gears are being shifted...

View 3 Replies

Saturn - SL2 :: 1999 - Engine Rev Up To About 2000 RPMs While At A Stop Then Drop Down To About 650

My '99 Saturn SL2 has from time to time in the past year or so had brief bouts where the engine will suddenly rev up to about 2000rpms while at a stop and/or drop down to about 650rpms combined with surging and stalling while moving. The Service Engine light would typically come on in conjunction with these spells, but then a few days later, things would be back to normal and the light would go off. The episodes seem to correspond with weather that has high humidity, but not necessarily extreme heat. Once or twice when the heat was above 90, the car quit completely and wouldn't restart for several minutes, but that was last summer.

About a month ago the car, which is normally parked in a garage, spent the whole weekend outside when we had some extreme rains (in air temps only about 60s or so). Since that weekend, the car is running frequently with the issues previously described, especially the surging and stalling while driving. It will feel like the timing of the fuel is all out of whack, will shudder and run hard, and then it will suddenly correct itself and run normally. A friend has a code reader and the codes that came up are 404 and 1404, which indicate the EGR valve. We replaced that with a new one and put in 4 new spark plugs, but the problem still persists. I believe the fuel pump is in the gas tank, so from other things I've read, a vapor lock may not be the problem since the fuel is being pushed.

View 6 Replies

Integra :: At Stop Light If Hit Brakes A Few Times RPMs Drop And Start Going Up And Down

Basically i have an integra here used to be a gsr with a type R engine. Basic bolt on's and 8lbs flywheel, 6 puck racing clutch. Here are the problems, i hate fixing other shops messes but here we go. When sitting at a stop light if we hit the brakes a few times every time we do it the rpm's drop and start going up and down, some times when the car is just sitting there idleing it does it. Had the same problem on a del sol with a gsr engine and b16a2 head on it done from the same shop. Also when its cold the owner complains that it will take him like 1/2 hour to start it. I was thinking that the grounding wasn't good enough. The check engine light is on as well, but how to get the ecu codes out of this ecu.

View 14 Replies

Dodge - Dakota :: 1996 - RPMs Will Drop To Near 0 Within About 20 Seconds Of Coming To A Stop

I have a code scanner which indicated that I should change the MAP sensor. I did that, and just for fun changed the idle air control valve and throttle position sensor. Now the idle is extremely smooth in park or neutral, but once I'm in a moving gear it's up to the same shenanigans, antics and tomfoolery I described in my original post: 96 Dakota SLT idles rough & stalls. So I have a 96 Dodge Dakota SLT 3.9 4WD. Anyway, it idles relatively smoothly at about 700 RPM in drive or neutral, but if I'm in a moving gear and need to stop, the idle is extremely rough. Usually, the RPM's will drop to near 0 within about 20 seconds of coming to a stop. It will typically recover and continue with rough idling and near stalling a few times, but within a minute or two it stalls. A few additional details: it starts right up again after falling, it doesn't make any difference if I start it cold and drive immediately or drive it for an hour before coming to a stop, the same thing happens. Anything that looked suspicious to me has been changed (drivebelt, spark plugs & wires, distributor cap & rotor, pcv valve, idle air control valve, and, of course, the air freshener).

View 1 Replies

Honda - Odyssey :: 2001 - Car Goes Into High RPMs (about 3000) Before It Seems To Drop Into Gear

I had my Honda Odyssey transmission replaced 2 years ago. The past few months, in the first mile that I drive the car on streets in our neighborhood, the car goes into high RPMs (about 3000) before it seems to drop into gear. It does this 2 or 3 times then works fine after that. The "Check engine" light is now on all the time. Sometimes, the car does one other weird thing--the high RPMs end with the drive/D4 light flashing on and off like a blinker (even if I change gears to D3. When this happens, if I turn the ignition off it comes back on and seems to function fine. I have had it back to the shop that did the work about 4-5 times to get it right. I like the guys but each time they return it to me, the problem remains. I took a 2000 mile trip with it and with the exception of this persistent problem, the van worked fine.

View 2 Replies