Ford - Windstar :: 2003 - Grinding Front Brakes On Occasion When Coming To A Stop
My 2003 windstar SEL needed new brakes and to have the rotors turned... instead I opted to buy new discs and pads online ... To my surprise the new discs were about a 16th of an inch thinner than the old.... I changed discs and pads and was happy for a few days, but now on occasion when coming to a stop the front brakes grind terribly....the next time i stop everything is fine...visa versa...dscs feel true (no pulsing) I DID APPLY BRAKE QUIET TO THE BACKS OF PADS....
View 2 RepliesFord - Windstar :: 2002 - Grinding Noise Going Up Inclines
My 2002 Ford Windstar Van needs a rebuilt transmission. The chain, according to my mechanic, may quit at any time (the van makes a grinding noise going up inclines). In 2005 my van had the transmission rebuilt (it totally quit on me driving). It currently has 200, 030 miles on it. I've checked around and the best estimate for a rebuilt transmission. Is it worth keeping? Repairing? If not, do I try selling it (for what amount?)?
View 9 RepliesFord Super Duty (1999-2016) :: Grinding Noise From Front?
1999 f250 super Duty V10... I am having some problems with switching out of four wheel drive. S, when I flip the switch back to 2 wheel drive everything, seems ok at first, but within a mile or two I will hear this grinding coming from the front that sounds like the gears aren't completely disengaging. The inky thing that prevents this grinding from happening is switching back into fire wheel drive and keeping it there. What might be causing it to not stay disengaged ?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: 4x4 Grinding Noise From Front?
My truck has been doing great over here in Germany, and I want it to stay that way lol. I know the snow is fast approaching here and figured I should test my 4x4(I usually do monthly anyway). After switching to 4-high and making the first turn in the open parking lot, I heard a lot of popping and grinding from the front end. I straightened the wheel and out and the grinding /popping continued.
I stopped, got out of the truck to try and lock the hubs to see if that would fix the issue. turns out the passenger side hub is locked up tight. I couldnt move it by hand and wasnt about to attempt to move it with added leverage.
What this could be? maybe a collapsed vacuum hose? but then I should still be able to manually turn my I hubs I would think.
Ford Super Duty (1999-2016) :: Bad Grinding Noise From Front Driveshaft / Differential
For starters I have a 1999 F-250 5.4l changed all 4 ball joints about 15,000 miles ago. I have been hearing a grinding noise coming from the front end for the last month only when I turn left and at slow speeds. I was servicing the TC so I threw it in 4 wheel to check it and it wouldn't engage until I started moving. When it did engage it was a bad grinding/ clunking sound coming from maybe the differential.
View 14 RepliesFord Super Duty (1999-2016) :: 2011 F450 - Front End Making Grinding Noise?
I've had the 450 a little over two years. Its used 95% of the time for hauling trailers, including the toy hauler. Has not given me a single problem since day one and now has around 21,000 on the odometer.
Lately I've noticed a "grinding" sound coming from the front end somewhere. It is most apparent when I'm turning at slow speeds; especially left. To describe it would be similar to worn out brake pads or maybe a wheel bearing going bad. It does it whether I'm on the brakes or not.
Ford Super Duty (1999-2016) :: Grinding Noise In Left Front When Slowing And Stopping
TRUCK: 2003 F250 S/C Long bed 4x4 7.3 Diesel
PROBLEM: grinding noise in left front when slowing and stopping.
Starts as a howling noise, turns into a grinding as you brake and come to a stop. I feel it in the pedal and as it slows it feels like metal to metal brakes
WHAT HAVE WE DONE: Replaced both front hub assemblies (MOOG)... Replaced dust shields, rotors, calipers, pads as well as all new brake hardware.
At any speed when I brake hard it grinds and howls, I have taken out the 4x4 locking hub assembly and it does not change the situation. I am stumped!
Ford Super Duty (1999-2016) :: F350 - Grinding Noise On Left Side Front
I replaced both front bearings, calipers, brake pads, now I have a grinding noise on the left side front stops sometimes when you step on the brakes? 1999 F350 ...
View 6 RepliesFord Super Duty (1999-2016) :: 2000 - Front Axle - Hub Makes A Slight Metallic Grinding Noise About 1/2 Way Around
I am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.
Ford Super Duty (1999-2016) :: 2001 F350 - Faint Grinding Noise In Left Front Wheel
I got a 2001 f350 got a noise in my left front wheel i know its not the wheel bearings, it only makes the noice when the locking hub is unlocked i did jack the the truck up and spun the wheel got a faint grinding noises form what seems like the locking hub so my question is bad locking hub or needle bearing holding the axle shaft??
View 3 RepliesFord Super Duty (1999-2016) :: 2004 F250 4X4 - Front End Rumble - Squeaking / Grinding Noise Then Clunking
So to start at the beginning.... Traveled across Canada East to West towing 11000lb travel trailer, no problem. Have used 4x4 in a few campsites to pull out of a pitch without spinning the wheels and causing damage to the site when it has been really wet. All good.
Got to Banff in December and the town was an Ice rink, engaged 4x4 and all good. Crossed the Rockies and the 4x4 starts making grinding noises. Up and down some mountains and squeaking, grinding noise then clunking.
I have manual hubs, disengage and the noise all goes away. Engage 1 hub and no noise. Engage both hubs, noise back.
I bought some needle bearings and went to swap them. Got hubs apart and they look good. No scoring on the drive shafts. They are not dry, but as I have them open, repack them with grease anyway.
Do more research... Remove ABS sensor and repack main bearings with grease. (broke one sensor pulling it out, too cold plastic brittle oops). Still clunking noises.
The universal joints look good, doesn't appear to be any play in them. However, the axle seal (knuckle seal) (F81Z-3254-CB) does move around a lot in it's metal casing. It is tight on the shaft, but with the hub off, I can move it in and out, and move it side to side. If I had ESOF hubs I guess they would not be locking as I'm sure there would be no vacuum in there!
Question is then, would this seal be allowing the universal joint to wobble under load in 4x4 mode? Would this wobble be the cause of the rumble? As it is labelled as a seal and not a bearing, I wouldn't of thought this would have been a loaded point, and the weight would have been taken by the associated bearings and it could be run without this seal? But if it is not this, then I'm still looking for a clue as to what is making the rumble....
Ford Excursion :: Pop Noise In Front End / Left Front Wheel Grinding
Driving at hwy speeds and head a pop noise in front end. Stopped and couldn't find anything, heard it a couple of more times, still nothing found, now I have a grinding noise left front wheel. What the issue may be. 2001 Ford EX 4X4.
View 6 RepliesAccord :: 1999 Honda V6 - Grinding Noise Coming From Front Driver Side Wheel And Smell Of Rubber
When I slam on my brakes there is a grinding noise coming from the front driver side wheel and the smell of rubber. Also when I do a u-turn the same thing happens. I own a 1999 Honda accord v6....
View 1 RepliesFord 6.0L Power Stroke Diesel :: Grinding Noise From Front End
I recently replaced the front wheel hub and upper and lower ball joints on the the driver side of my 2004 f250 CC SB 6.0 fx4. Now when I put into 4 wheel drive I get a grinding noise that sounds like a worn out break pad from that side only. It didn't do it before and it only happens in 4x4. I have replaced the wheel hubs before and it was fine. Also The needle bearing race on the axle is good.
View 4 RepliesFord Excursion :: Grinding Noise In Front End On Left Side
Had a grinding noise in my front end, left side. Found the hub was bad so got it replaced. Now I still have a grinding noise that comes and goes. If I hit a bump, it starts the grinding noise but nothing constant. Had the front end checked and nothing was obvious. Was trying different things and when I put it in 4WD, with the switch on the dash, the noise goes away. What to try next?
View 2 RepliesFord - Focus :: 2004 - Grinding Noise From Front Passenger Side
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
Ford F-150 (2004-2008) :: Grinding Noise From Front Passenger Side
2005 ford f150 Fx4 So last Friday I started hearing a grinding noise from the passenger side front of my truck. sounded like metal on metal. So I started rooting around and noticed that bottom ball joints were shot. so replaced bottom ball joints on both side. I aslo replaced wheel bearing hub assembly on both sides, still heard the grinding. So I noticed that both axles were slinging grease, so I replaced them on both sides.
Still heard the grinding noise. So then I removed everything from the passenger side and noticed that the locking hub actuator was grinding both axle and the wheel bearing hub. So I just got done replacing that on the passenger side, put it all back together, and still grinding noise ringtones free. Also replaced the 4wd solenoid that they said gets water in it, and I replaced the check valve. And I put new Rotors and breaks. What it could be?
Ford F-150 (2004-2008) :: 2006 - Grinding Noise On Both Sides In Front End
I just bought 2006 f150 4wd . It make a grinding sound on both sides in the front end..it seems to be independent and when I slow and come to a stop, I makes a clanking noise like its locking something in.
View 4 RepliesFord F-150 - 1997-2003 :: 2002 - Grinding Noise From Front Differential
I have a 2002 f150 5.4 with 3.55 limited slip... For months now every time I hit a bump with the front right side there is a loud bang (sounds like a wore out bushing), and if I am driving slow at an idle you can here a thump every time the wheel goes around. And when I turn all the way it sounds more like a grinding sound.... The noise is getting very bad, what it is. I am very mechanically inclined but cannot figure it out.
Everything in the front end seem tight. When I lay under it if I get someone to spin te wheel the thump sound sounds like its in the front dif, kinda echoes through the front drive shaft but u joints seem good. I really think it's in the dif, and I'm hoping the banging noise I hear when I hit bumps is the same problem as the noise when the wheels go around....