Thunderbird :: 1986 Won't Stay Running / Smell Of Gas
My Grandfathers Thunderbird has sat for 5 years. I need to get it running again. I can hear the fuel pump build pressure, replaced fuel filter. After cranking on it, eventually it will start. When it starts to die, I give it some more gas, RPMs increase but it doesnt run much longer. I do smell gas after it dies. After a couple times of this the battery has to be recharged. I hook it up to a jump at 55amp's and it will start once more and then die. Also, I did drain the fuel and put in half a tank of new gas and 1 - bottle of gas treatment.
View 1 RepliesEscort :: 1991 Ford Starts But Won't Stay Running
i have a 1991 ford escort pony i w driving it fine all day then all a sudden i stopped to get water the car died when it did i tried to restart it , it bogged out and didnt start i waited a hr it started idled for 20 mins reved it up everything seemed ok but then i went to actually drive it i got 1/3 of a mile if that and it died on the side of the road with my lil daughter in the car and 104 degrees outside. me and my father thought it was a furl filter or pump but in the primer valvei t has plenty of fuel and pressure. what it could be?
View 1 RepliesFord Excursion :: Starts But Won't Stay Running When Cold
When its cold outside it starts and runs good for about a second and then shuts off or runs really rough and then takes off. I tried turning it off and starting it about 4 times. After the fourth time I gave it a little gas and it started after that. If the block heater is plugged in it starts fine. And starts great the rest of the day after the initial start. It is not that cold here, lower 20's in the morning. Where to start with this problem?
View 13 RepliesCherokee :: 99 JGC Limited 4.7 Starts But Would Not Stay Running
So our battery died and after getting it jumped the Jeep would not stay running. As long as I was giving it gas it would stay running. As soon as I stopped giving it gas it would die.
View 4 RepliesMercedes - Benz :: 1989 - Car Starts But Won't Stay Running
I have a 89 Mercedes 190e. The car stays running and will drive but after so long starts acting like it's starving for fuel. I have spark and nothing wrong with fuel filter but when tested there was no pressure what's odd is the fuel pump was tested and it works fine all the lines have been cleared I'm stumped what else can I check...
View 13 RepliesCivic - Honda :: 1992 - Starts But Won't Stay Running
1992 Honda Civic Starts fine but kills as soon as you release the key. Hold the key in the position with the starter motor running and it keeps running. In the old days we would replace the resistor on the firewall. Today?
View 3 RepliesS-10 :: 1999 Chevy 2.2 L Just Shut Down While Driving Now Starts But Won't Stay Running
I have a 1999 chevy s10 2.2 L that just shut down while driving, I have replaced crank shaft sensor, ecm, ignition control module, coil packs and still having issues, she will start now but won't stay running, what else it could be, it has been down for almost 5 months.
View 1 RepliesCivic - Honda :: 2002 LX Automatic Starts But Won't Stay Running
I recently replaced the transmission in my car. I put new oil pan gasket, valve cover gasket and plugs in it. Got everything back together and now it won't stay running. It starts but will not stay running . I pulled the plugs out to find they were the wring ones that a was sold So They gave me the correct ones. Still doing the same thing. I've checked every connection. All are plugged in all lines are hooked up.
View 4 RepliesChevrolet :: 1982 - Small Block Starts Up But Will Not Stay Running Idle
I just bought a 1982 Chevy c10 305 small block.It had an oil leak so i began putting new valve cover gaskets, and then New Valve Covers(Edelbrock). Because the covers were taller, I had to remove the EGR valve and bend a new fuel line.There was a plate i installed inside the valve cover where the PVC goes into? is this a problem?I noticed the hose from the distributor rotor button(vacuum?) was not connected to anything.I plan on putting a EGR blocker plate, but was told it wasn't needed to run.
So now it starts up but will not stay running idle. Do i need an EGR blocker to run?IS that plate needed inside the Valve Cover?Does the hose from the Distributor rotor need to be connected?
Ford - Thunderbird :: Gauges Stay On And Low Fuel Light Lit Up After Turning Car Off Completely
My 1995 Ford Thunderbird has a problem when I turn it off. After turning it off and removing the key the gauges still stay on and the low fuel light come on even though there is a full tank. Every other time I turn the car off the heater fan turns on even though it is in the off position. I replaced the ignition switch and cylinder but it didn't make a difference. I'm thinking it might be the ECU but I don't want to just start replacing more and more things trying to find this out.
View 5 RepliesGti - Volkswagen :: 1996 Will Not Stay Running / Turn Over But Won't Start
Its a 1996 vw gti 2.0 it wont stay running. Changed the spark plugs, air filter, distributor cap. itll crank but wont start. if i give it gas it will start. but you have to stay on the gas to keep it running. when you let off the gas, it dies right away. Could it be the mass air flow sensor?
View 2 RepliesGrand Prix :: 2004 Engine Cranks / Turn Over But Won't Stay Running
The engine cranks and turns over when I turn the key, but won't stay running unless I give it some gas. My mechanic doesn't know what's wrong with it, but I haven't starting having him replace parts. What's going wrong. Could it be the fuel filter? fuel pump?
View 9 RepliesFord Super Duty (1999-2016) :: 2005 - Vacuum Pump Starts Running And Won't Turn Off After Start Up?
I have a 2005 F250 , 4.2 tdi diesel. I just bought the truck recently and still getting to know it.
I noticed recently that when I turn on the key, the vacuum pump starts running and does not go off. It seems to run continuously and will only shut off if I block the white outlet pipe with my finger. Is this normal or is the pump stuffed.
Ford - Thunderbird :: 1995 - Won't Start / Clunk When Try To Turn It On
my 1995 tbird just sat for a year i replaced the battery but when trying it it clicked it actually clunked i replaced the starter put a jump on it still clunked when trying to turn it the surpentine belt did move inches at a time what else can i try?
View 7 RepliesFord Ranger / B-Series :: 1986 - Starts And Runs Rough / Bad Misfire
My pops has a 86 ranger with a 2.9. And what its been doing is, it will start up just fine then u give it a minute and itll start to run very rough like a bad miss fire, then if he revs it up for a bit. It will clear out and then run just fine until he starts it up again and it seems to do it more the colder it gets and it smells very rich. Iv checked the injectors and there fine, what other things could it be ? O2 sensors oorrr
View 5 RepliesNissan :: 1986 - Dash Warning Lights Stay Lit And Flicker For 20-30 Seconds Then Go Out
After starting my truck the dash warning lights (oil, battery, brake, low fuel) stay lit and flicker for 20-30 seconds then go out with the exception of the battery light. It remains dimly lit for 2-3 minutes before finally going out. The battery and alternator have tested OK. I cleaned the battery ground connections andreplaced the check light relay. Still the same situation. '86 Nissan Hardbody Pickup ....
View 1 RepliesFord Fuel System :: 1986 Ranger Starts Only When Spray Starter Fluid Into Air Intake
My 1986 Ranger 2.9 starts only when I spray starter fluid into the air intake. It does stay running and it drives fine. The engine will not fire up unless I do this process. I have cleaned out the fuel rail, fuel injectors, purchased new fuel filter, and tested fuel pressure (which is good).
View 9 RepliesFord Ranger / B-Series :: 1986 - Gas Will Not Keep Engine Running
1986 Ford Ranger / 2.3 EFI / 140 CID OHC /4-Cyl/5 speed
So the last time I was here, I was having doggy issues which I thought were fuel related. I'm still having issues, although it appeared to cleared up a bit.
When I start the engine, it cranks over, I'd give it some gas, it would rev up, then suddenly die, no matter if I pressed down on the gas pedal or not. After two or three times doing this, it would turn over and maintain a steady idle, then off I go.........
The problem now? Well, late today I tried to get it going, and after about 15 times, I gave up. It would not stay idling, it would crank over then die. I did not want to ruin the starter. It seems the gas pedal is worthless after the engine decides to conk out, and no matter how many times I step on the gas pedal, nothing happens.
Has been replaced within the last few months:
Fuel filter regulator,
Inline fuel filter,
Cap and rotor,
Lucas fuel injector cleaner,
ECC computer, and Fuel relay switches, (multi-function relay/connector switch)
Air Control Valve - Removed and cleaned.
Checked all vacuum hoses.
Has not been replaced:
Map Sensor, (was told it's located on Pass. fender wall, but can't find it, according to the manual)
EGR Valve and sensor,
Throttle Position Sensor,
EVP sensor,
Spark plugs, (two years ago)
Plug wires, (two years ago)
Ignition control module, (replaced about six years, or more)
With trying to keep the gas going to turn it over, it does not, so to me, it seems to be more of a fuel problem than electrical, but I'm no mechanic.
Ford Fuel System :: 1986 F150 - Engine Is Running On 4 Cylinders 1 / 4 / 5 And 8
What to do next. Engine is running on 4 cylinders, #1, 4, 5, 8. Had a mice nest on top of injector #2. Removed mice nest. The mice had chewed through wire for #2 injector and caused bear lead rubbing on the block. One lead rubbed through. Repaired, splised in a wire. Also changed rotor, rotor cap, all sparkplug leads and plugs.
Troubleshooting.
Compression on all 8 cylinders measured to be above 160 psi.
There is spark to all 8 cylinders, including the other 4 cylinders, 2, 3, 6, 7 that is nor developing power.
Fuel rail pressure is 35 psi on idle and spikes to 43 when reving the engine.
The fuel injector resistance all all measured injectors are the same (about 14.8 Ohm). Measured injector # 1, 2, 5, 6, 7, 8. Injector # 3 and 4 is hidden and require too much disassembly. Visual inspection deems wire for #3 and 4 injector to be ok on top of block.
Electric impulse (tested while engine was running) to injector # 1, 5 and 8 are ok, used test lamp to see that there are electric impulse to the injectors. Injector #2, 6 and 7 does not have any electric impulse. Unable to check electric impulse to # 3 and 4. However cylinder #4 develops power. Used moving the sparkplug wire for cylinder #4 to verify that is is developing power.
What would my next step be? Where should i look next?
1. Where is the control module and is it likely to fire to only 4 cylinders
2. Could it be an wire in the pickup element, under the distributor. All wires seem intact.