Ford Ranger / B-Series :: 2003 - Hard Shift - Transmission Or Clutch?
The truck: 03 Ranger, 2wd, 2.3L, 5spd, 160k mi
I bought the truck two years ago and it's always been difficult to shift (especially into 1st, 2nd, 3rd). I don't drive it often and only put 5k mi on it since I bought it.
The problem: Someone more mechanically inclined than I once told me that the hard shifting is probably due to the clutch not fully releasing due to low hydraulic pressure brought about by a failing slave cylinder.
I just noticed today that there is a high-pitched squeaking coming from somewhere on the truck. At first, I thought it was the rear end, but now, after pulling it into the driveway, I noticed that the squeaking noise vanishes when I push in the clutch pedal and returns after I release the clutch pedal and drive in 1st gear.
The transmission oil level is good, but I've never changed it and I'm not sure if the previous owner ever did either. I'm hoping I haven't damaged the transmission.
After reading a few threads, it seems the problem might be the input shaft bearing. To replace it, I'd need to drop the transmission and borrow a couple of tools I don't have (feeler gauge and bearing puller). If the ISB is the problem, it seems like it would be a good idea to change it now before it seizes and leaves me stranded somewhere.
Golf IV R32 :: Whine Sound When Press The Clutch To Shift At High RPM
My R is stock. When I accelerate hard and shift, I can hear like a whine noise when I press the clutch to shift.
Its like something continue to spin fast when I press the clutch at high rpm.
Ford Ranger / B-Series :: Soft Clutch / Gears Grind When Shifted Especially 1st And 2nd
I have a 96 2.3L 5 speed Ranger. The clutch has been getting softer and softer until about two weeks ago when I couldn't drive it anymore because gears would grind like crazy when I shifted, especially 1st and 2nd. I had no time and just drove my other truck but now I've had a bit of time to look into it. I went to bleed the clutch and then realized there was no fluid in there. So I tried to put fluid in but nothing happened. The clutch is still extremely soft. The truck won't even start when I have it in gear, it turns over and kind of lurches forward, even with the clutch pushed all the way in. It starts right up in neutral. So my guess is I have to do what I really don't want to... replace the clutch!!
Is it possible that since I just put more fluid in the clutch it may take awhile for that fluid to get into the cylinder and I have to bleed it again?
Ford Ranger / B-Series :: 2002 - Hard To Shift Gears
I have a 2002 ford ranger edge. swb, 3.0L, 5spd. I have been noticing it is getting harder to shift gears, put in 1st at a stop light lately. There is no grinding just seems harder to engage. Checked fluid level and it is clean and full. Recently i have developed a vibration under power. Let off the gas and smooth as can be, apply throttle and starts vibrating. Not sure if flywheel is "hot spotted" or perhaps broke a spring on pressure disk. Just seems odd it's only under throttle. Yes already checked rear end and U-joints.
View 2 RepliesFord - Ranger :: Clutch Pedal Feels Normal But No Resistance When Shifting Gears
I have a 5-speed transmission pickup (’04 Ford Ranger EDGE SuperCab). Clutch pedal feels "normal", No resistance when shifting gears. Will go into gear with ease, except for 2nd gear (grinding noise), must push clutch to the floor and still grinds; but only 2nd gear. In 1st gear, my truck will slowly creep forward as if unable to engage and not having any kind of pulling power. Even when shifting to 2nd, 3rd, 4th and 5th gears, it barely maxes out at 30MPH (top speed unless vehicle is on a slope or slight decline then I can get up to and over 40MPH. Checked brake fluid level, it’s ok. The fluid’s at max. Clutch is relatively new (April 2014), with only about 13,000 miles on it, if that. It must be cylinder issue. Is there any way to tell whether it's the clutch master cylinder or slave cylinder?
View 5 RepliesFord Ranger / B-Series :: Column Shifter Too Hard To Shift Through Gears?
I've been having problems with my column shifter ever since I installed a Pioneer shift cable probably about 3 years now. I was told and also thought that the cable would loosen up after awhile but it never has. I had some put it on and I watched him do it. He seemed to have some trouble because it took him a long time under the dash. It shifts so stiff that over a period of about 2 years it finally broke the end of the shift tube one night. Luckily I was able to fix it the next day by getting a spare without missing any down time. It was still just as stiff with the other shift tube. It finally broke the plastic on my shifter tonight, not necessarily whatever is causing it but because it takes so much effort to shift into Park, Reverse or Drive.
I think the plastic may have cracked over time. Luckily I had another one at home along with another shift tube. I didn't replace the shift tube this time but I did remove the caps and smear some grease on the bushings to see if it would make it turn. I looked further down at the end cap that broke last time and sure enough one of the bolts was backed almost all the way out. I retightened it tonight too. That's what happened when the bottom broke last time. One of those bolts backed out and it cracked the housing. It works now but if you go all the way to 1st to get back to anywhere it really takes a tremendous amount of effort to get it to shift. Something is not right and I cannot pinpoint it. I know they offer brand new shift tubes but I'm not sure if that's the problem.
Ford Ranger / B-Series :: 1997 - Transmission Hesitates / Struggling To Shift Into Gears?
1997 2.3 5 Speed. My poor truck is having a hard time shifting into gears. I have bled the master off the truck with the correct method, bled it on the truck with the hose on the slave method while pushing the pedal and multiple times with no bubbles coming out at all, no leaks, etc.
Here's the breakdown -
- Clutch, slave cylinder and shifter bushings replaced about 3 years ago (everything has less than 7000 miles on it)
- While driving and pushing in the clutch, it clearly disengages, although quite a ways down.
- Only shifts hard while running. If I sit with it off with the clutch in, I can shift through all the gears with no effort whatsoever. At times while driving, it gets so hard to shift that it may become dangerous.
- Only things I haven't replaced are the master cylinder and the flywheel.
Should I just assume a bad master and just replace it? It's the original with 188,200 miles on it.
Forgot to mention there are times that when I am at a standstill trying to go into reverse, it grinds like the transmission is still engaged.
Chevrolet - Tracker :: Clutch Goes Away And Unable To Shift Gears After Driving For About 30 Minutes
98 tracker with 5 speed manual transmission has new clutch pressure plate throwout bearing and shit cable. strictly mechanical clutch mechanism drive for about 30 minutes and clutch goes away and unable to shift gears. let it sit overnight will work until about 30 minutes of drive time when everything has a chance to heat up...
View 8 RepliesFord Ranger / B-Series :: 1999 XLT V6 - No Clutch / Can't Shift
When I got home today I went to back into my parking spot and couldn't get my truck in reverse, or any other gear for that matter.
I've been suspecting something was going to go wrong because the last few weeks or so when I push the clutch in it sounded like bb's rolling around in a metal coffee can. Since I have owned it (2 yrs) the clutch has seemed funny anyhow, as in I really have to feather it so it doesn't grab and stall out.
So I've visually inspected what I can so far. Master cylinder fluid is at a proper level and I pulled the inspection cover on the transmission. I didn't see any fluid and reached inside and there wasn't residue in there either. I observed the throwout bearing pushing the clutch cover fingers in when the pedal is pressed and that is about it.
Just wondering about some additional checks I can perform to pinpoint the problem, as well as how to fix it and get rolling again.
1999 Ford Ranger 4x4 XLT
3.0 V6
134,xxx miles
No modifications
Ford F-150 - 1997-2003 :: 1999 V6 Will Rev Real High When Press The Clutch While Sitting At A Light
I bought this truck for work and all of a sudden it will rev real high when I press the clutch in to switch gears or when sitting at a light. I stopped at a parking lot and popped the hood and tried to pull the throttle back by hand but it will not go. There is a lil slack in the throttle cable but when the truck is off and I manually pull the throttle back it returns normally.
I was wondering if the little black electronic box opposite where the throttle hooks to the throttle body is making it rev so high? I really don't know a lot about these newer trucks as I have driving older trucks my whole life so probably using wrong terms...
GTI 337/20th Anniversary :: Clutch Sticking When Released And Gears Only Engage When Push Hard Shift Knob
Been having trouble shifting into any gears on these chilly mornings in VA now... The clutch has been sticking on its way out when I release it and the gears don't want to engage unless I really push hard on the shift knob.
View 11 RepliesFord Ranger / B-Series :: New Clutch - Hard To Shift Going Into 1st / 2nd And Reverse Intermittently
1997 Ranger extended cab, 222k mi., 4 cyl, standard transmission. Shifting got worse until it finally died and the mechanic replaced the clutch "kit" and slave cylinder.
It still fights back going into 1st, 2nd, and reverse. But it is intermittent. If I put it in neutral, depress the clutch, and start the vehicle, then, after a few seconds wait, when I try to go into 1st (or reverse), it fights me back, forcing me to pause and apply about twice the pressure I should need to go into gear. When I go forward in 1st, and am ready to shift to 2nd, it fights back so that I have to pause just a bit and apply more pressure than I should for it to go into 2nd gear. 3rd, 4th, and overdrive are FINE. Also, the clutch seems to disengage about halfway down, where I was expecting it to disengage after only 10 -20% depression.
The mechanic doesn't see the problem (or won't admit it). Is there an adjustment to make the clutch disengage with only 10-20% depression instead of the 50%? Is that something I should be worrying about?
Is there some other problem? Like maybe the synchromesh mechanism in the transmission itself not bringing the transmission rotor to engine speed soon enough (wear on the synchromesh)?
When it was new, it went into ALL gears with ease, no fighting back, and it starrted doing this after about 150k miles. Now, at 222k mi., even with a new clutch, plate, throughout bearing, and slave cylinder, it still seems partially stuck going into 1st, 2nd, and reverse.
I just don't want to start replacing things until I can get a correct diagnosis as to what is causing the problem.
Elantra MD (2010-15) :: Throttle Delay / Hesitation When Press The Clutch And Rev The Engine
Picked up the car 5 days ago but noticed when I press the clutch and rev the engine, there's a throttle delay/hesitation and a simultaneous sound like "psshht". The sound is almost like when you're shifting a turbo car with a blow off valve.
Other than that the car is great. 2012 Elantra GL manual ...
Golf IV / Jetta IV :: 2003 - Hard To Shift Into Gears
My 03 Gli 24v manual transmission has been acting up lately. First it started to get a little difficult to shift into gears about a week ago. Then tonight i was driving through a parking lot in 2nd, and after i came to a stop i tried to put it back in to first and it would not go into gear. As i was trying to get it into 1st i could tell it was grabbing a little bit and the car was inching forward.
I got it to a parking spot and starting reading about other peoples issues, one i read said they were able to get it to move after pumping the clutch some. After trying that i was able to get it into gear and drive it to my parents. Looked at my brake fluid and its full. Took it for a test drive around the neighborhood and it was shifting fine at first then started getting a little difficult to shift again. I tried taking off in 6th and it stalled. I tried going from 1st around 3k-4k rmps to 6th and it was still driving with very little lugging. My clutch feels and is still stiff, not loose at all. I do have to go all the way to the floor with the clutch before im able to shift
Finally to my questions. Could my clutch be going bad? Could my cables need adjusting? Something I read about a pressure plate maybe?
Nissan - Xterra :: 2003 - Grinding Noise Whenever Shift Gears
2003 Nissan Xterra 2.4. It grinds when I shift gears, gears through 2nd thru 5th.
View 8 RepliesFord Ranger / B-Series :: 2003 4.0 - Rev Limiter At 3000 RPM / AC Clutch Not Engaging?
So that's what if feels like, in park at idle it sounds great, starts great no codes. IF you floor it it will not go over 3000 rpms in park, it feels like it has hit a rev limiter. I have 60psi fuel pressure at idle and at 3000 rpm.
When driving down the road I won't go over 55 mph and drives normal if you keep it under 3000 rpm, if you give it more gas it falls on its face?
AC is not working (clutch not engaging)I don't know if that's related or not.
We did just swap the motor the truck is a 2003 2wd drive. motor came out of an 2002 4wd. we are running the 2wd harness, computer egr delete etc.
Ford Ranger / B-Series :: 2004 - Revs Engine When Clutch Engages?
2004 Ford Ranger revs the engine when you engage the clutch then when you place it in gear it's like the cruises on it want to drive without you touching the Accelerator?
View 4 RepliesFord Ranger / B-Series :: 2003 - Hard To Shift After It Warms Up
I bought a 2003 Ford Ranger, 2.3, 5 speed manual. It is hard to shift after it warms up. I test drove it when it was below freezing, so I didn't notice it at first. The warmer the day and quicker the truck warms up, the worse it is. It goes into gear with no problem when the engine is off or if I'm still moving, but if I'm stopped there are times it is hard to get into gear. This really sounded like a clutch that wasn't fully disengaging to me, so I decided to pull it apart. I didn't check the movement at the slave before I started, but I did find the master was a little wet at the rod in the cab.
So, I did the following:
- New clutch master cylinder (system bled out of truck to eliminate air)
- New slave cylinder and bearing
- New pilot bearing
- Changed transmission fluid - Mercon III ATF
I inspected the clutch/pressure plate and it was in good shape and looked like it might have had 10K - 20K miles on it. The last owner said it was recently replaced and it looked it. So, I put it back in. After I was done, I checked the movement at the slave/pressure plate and it is moving about 3/8" - 1/2" when the pedal is down. I was happy and thought this would solve the problem since the old pilot bearing seemed stiff and I saw the leak on the back of the master cylinder.
I drove it and all felt fine at first, but it was a cool day and I didn't drive it that long. When it was warmer over the next couple of days, it started getting hard to shift again. It's not been quite as bad as before, but still doesn't shift right.
Ford Ranger / B-Series :: 2003 - Sluggish To Shift Into 2nd Gear?
2003 3.0 FFV 5 speed automatic...... Just noticed recently that it seems slow to go into 2nd gear.....the rest of the shifts seem fine, firm and unchanged.....
View 4 Replies