Ford F-150 (2004-2008) :: Left Front Wheel Bearing Keep Going Bad
What is causing the right front wheel bearing to keep going bad on my 06 f-150 2 wheel drive....
View 1 RepliesFord F-150 (2004-2008) :: Wheel Bearing - Hard To Turn One Direction
Have a wheel bearing going south can it make the car hard to turn one direction. I dont really have any humming like a wheel bearing does. But i feel a little resistance every now and then when turning the steering right. I have sprayed the steering shaft joints and i can see that they are moving free like they should. And i have a less than 2 yr old steering rack. My truck has 103k miles on the original (to my knowledge) bearings. i didn't know if sometimes a wheel bearing could cause a hard to turn in one direction feel.
View 14 RepliesFord F-150 (2004-2008) :: Repeated Front Hub Failures - Wheel Bearing Grinding
Repeat Front Hub Failures -- 2WD Try this situation -- Purchased 2006 F-150 XL with 57,000 miles. Truck built on 05/24/2006.
Sept 2011 68,621 miles -- Left front hub failure -- Wheel bearing grinding -- Done by Bell Ford in Phoenix.
2013 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2014 -- Left front hub failure -- wheel bearing grinding -- done by independent shop.
Sept 2016 -- Upper & lower control arms, struts, strut mounts, springs replaced -- Quality part used -- Complete front end alignment -- Brake job front and rear.
Nov 2016 -- New performance exhaust system due to exhaust leaks.
Dec 2016 -- Failed automatic transmission -- Remanufactured FORD transmission installed w/ 36 mo warranty. Sanderson Ford gets an A+
March 16, 2017 151,000 miles -- Left front hub failure -- wheel bearing grinding! Verified by jacking up truck and spinning left front wheel -- GRIND! This is coming from down in the hub. This is a 2 wheel drive truck. Yes, you counted correctly, this will be the 4th replacement on the Left side!
NO Towing! NO Overloading! Wheels are 2006 XLT style Aluminum rims with P235/70R17 Michelin XLT M/S (Defender LTX) tires all around.
It only hauls maybe 200 to 300 pounds of electronic equipment at the max, once in a while. This is driving me crazy! I always use FORD PARTS for the HUB ASSEMBLIES. Really loosing faith, the front right hub is OEM original - NEVER CHANGED!
Ford F-150 (2004-2008) :: Driver Side Wheel Bearing Squealing Pretty Bad
I just replaced my drivers side wheel bearing that was squealing pretty bad. After replacing it I now have the same noise only consistent where before it was only when I turned the wheel to the right. I noticed the teeth in the cv shaft where a little warn down when I changed the hub. Now also along with that noise I'm getting a clunking sound. Should I just change the cv shaft or is there something else I need to be looking at?
View 1 RepliesFord F-150 (2004-2008) :: Steering Wheel Occasionally Clicks When Turning - Bad Bearing?
I have a 2004 F150 SCrew 4x4 with the 4.6 (260K)... My steering wheel occasionally 'clicks' when turning - It sounds and feels like a bearing is bad in the steering column.
When it happens, it feels like one in the bearing is binding- the steering wheel slightly binds, then there's a 'pop' like the ball snapped back into place. This only happens occasionally. Sometimes it will pop with every revolution of the steering wheel, other times not at all.
Originally, I thought it was a U-joint, but it seems like the noise is coming from the bottom of the column...
Ford F-150 (2004-2008) :: 2007 - Speed Related Ticking Sound / Wheel Bearing?
The front driver's side wheel of my 2007 Ext. Cab makes a speed-related "ticking" sound. It's usually audible but not always there. I look for rocks in the tread of my BFG All-Terrains and sometimes I find some, sometimes not. The noise seems to be independent although some of the rocks really get up in there. Sometimes its really loud and it sounds like a rock. Bearing? 4WD CV or U-Joints or whatever?
View 6 RepliesFord Super Duty (1999-2016) :: 2004 F250 4WD - Front Wheel Bearing Replacement
So I have to replace the front unit bearings on my 2004 f250 4wd. My question is, which thread pattern I have, fine or coarse? I have read that the early models, 99-02 have coarse threads. Afterwards they are fine. I am going to order online as they are cheaper than the local parts store. I have the Timken part numbers for either thread pattern.
View 4 RepliesPrius (2004-09) :: ABS Light On After Wheel Bearing Replacement
My 2006 Prius with now 68,000 miles just had both front wheel bearings replaced today from an independent shop in town with a good reputation.
View 13 RepliesCorolla :: 2004 - Wheel Bearing Whine Now After 125K
I'm hearing a wheel bearing "whine" now after 125K on my salvaged Corolla. How do I replace the front wheel bearings on a 2004 1.8L Corolla. Any special tools required.
View 2 RepliesCamry :: 2004 Constant Low Rattling Sound From Wheel Bearing
Camry 2004, 50,000 miles
Last week my car started to give out loud thud noise from the rear passenger side wheel and shook as I accelerated. My wheel bearing was bad and leaking. Replaced it. The loud thud noise and shaking are now gone.
However, I hear a constant very low rattling sound from the same wheel when I cruise above 40 mph. Time to time I also hear a loud rattling tin can sound lasting for two seconds, and it mostly happens when I make right turns.
Chevrolet - Venture :: 2004 - Tire Or Wheel Bearing Noise
I have a 2004 Chevy Venture van, the front tires wore out on the inside, badly. DH adjusted the toe (made the rod shorter, so made it more toe-out?). We got new tires, after 1000 miles, they were again wearing on the inside. I convinced him to get a front end alignment. After the alignment, there is a lot of road noise, goes away when you go around a right turn. Could it just be the tires wearing differently, or is it a wheel bearing, and could that have been affected by the alignment? We have driven 150 miles since the alignment and it still is noisy.
View 11 RepliesPrius (2004-09) :: Noise In The Right Front Wheel - Bearing Failed
I devloped a noise in the right front wheel. I thought it was a tire going bad so I rotated the tires & still had the noise. I was told by shop it is a wheel bearing. If that is the problem is that a DIY repair ?
View 5 RepliesLexus RX 2004-09 :: RX400 AWD Vibration At Higher Speed - Bad Wheel Bearing?
I've been feeling more and more, a vibration in the RX400 AWD. Just to be certain, I had the tires rotated and balanced....still there. My conclusion is a wheel bearing.
What I notice, from 60 up to 80 MPH (speed limit in WY & MT), a slight vibration in the car. I can't pinpoint if it's front or rear, but there is certainly one occurring.
So, is there anything else that could contribute to this or is it usually a wheel bearing going bad? I just drove 1200 miles over the holiday and didn't notice much of a change. Still vibration. Not so strong that my wife has noticed, but enough that I'm feeling it.
I assume it's just a complete assembly and can be changed out relatively easily. I've done my 4wd suburban so I'm guessing similar in work.
How to test which assembly is going bad? Front/Back....Left/Right?
Prius (2004-09) :: Scraping Sound From Right Front Side - Wheel Bearing Went Out
For several days I could hear a scraping sound from the right front side. I thought it was snow packed in the wheel well at first, until there wasn't any snow there. Today I was driving on the Xway and the scraping became a buzz like a Cessna airplane. On the way back home I turned the steering wheel back and forth and sure enough the buzz came and went. That made it sure to me the wheel bearing was bad.
View 19 RepliesSebring - Chrysler :: 2004 - Stuck Wheel Bearing Assembly Removal?
I'm attempting to replace a front wheel bearing and hub assembly on a 2004 Chrysler Sebring. I've removed all the hub bolts and all other more external components. I've tried hammering the assembly, reinserting the bolts partially and hammering those, a slide hammer, liquid wrench...
View 9 RepliesPrius (2004-09) :: Corrosion On Steering Knuckle Where Wheel Bearing Hub Assembly Seated
I have removed knuckle assembly and pressed out bearing hub assembly, I have the new bearing hub assembly..... I live in Iowa so there is corrosion on the knuckle assembly - I have removed enough that the new bearing assembly will go in....
My question/concern : With the corrosion removed the surface of the knuckle where the bearing will seat is not uniform all the way around. The bearing hub assembly will go in and will require pressure to do so but will the bearing last? I can buy a steering knuckle but do not want to if I don't have to.
Prius (2004-09) :: Faint Whup Between 35 And 50 MPH On Front Driver Side Area / Bad Wheel Bearing At 30K
At about 20k on my 07 I started hearing a faint whup whup whup between 35 and 50 mph's on the front driver's side area. At 60+ pretty quiet. It has gotten real loud at the present 30K. I suspected the tirers as I know the Integrities are complete junk but as a test I did a rotation and exact same noise.
I thought thats not good but found it hard to believe something else was bad as I had no vibration and no pull whatsoever in steering. Long story short I bought a new set of tires Kumho KR21's at stock size and oh crap exact same noise.
Lexus RX 2004-09 :: RX330 Rear Wheel Bearing Type Noise Gets Louder With Increasing Speed
I have a rear wheel bearing type of noise that appears to come from the rear. My vehicle is front wheel drive and has 135K miles.
I checked the rear wheel bearing/hub assys on both sides and they had no play but I changed them anyway. Noise did not change at all. Rear tires have normal wear, no cupping or anything. Noise gets louder with increasing speed up to a point and then remains a constant level.
My next thought is to check the front wheel bearings/cv joints.
Ford - Mustang :: Whirling / Grinding Sound Coming From Front Right Wheel That Comes And Goes
A little less than a month ago my wife's old 1999 Mustang had the tires replaced. Since that time there she has noticed two new sounds:The first is whirling/grinding sound coming from the front right wheel that comes and goes. The second is a low, loud groan that seems to come from the front of the vehicle when the brakes are applied. The groan varies in intensity but seems to always be present when the brakes are applied. The groan is not unfamiliar to anyone that's driven an older car, but it is much louder than I have ever seen on any other car (on the other hand I usually drive a Corolla so it may be normal on a V6 Mustang ).
The first sound seems to have been reduced but not eliminated since I followed the advice in this video below and pushed the plate behind the wheel back a bit with a screwdriver. Now it is only audible when the engine is off and the wheel is spun (in other words, when it is sitting on a jack and the wheel is spun by hand), but it is still there.
I took it into the shop where the tires were purchased and mounted. The good people at the shop did rotate and balance them, but both noises remain.
I looked at the calipers and discs and everything seems in order except (possibly) two things. The discs have rust around the edges not unlike the ones in this photo below and I have no clue if that is normal or a problem. The rust is present on all wheels and only the one makes that noise, so I think that may not be the source of the sound,. On the calipers some substance (paint?) is peeling off, but otherwise they look fine and again the same is true on all the wheels so it seems that is unrelated to the noise. I have not been able to get a look at the pad, so I don't know what condition they are in.
Other information: The serpentine belt was replaced a few days after the new tires were installed. The radiator was flushed at the same as the belt was changed. They also threw in an oil change and all the fluids checked at the same time. The tires are new Michelin Defender size 205 /65 R15 and all 4 tires are new. The engine is a V6 and the transmission is automatic.
[URL] .....