Scion - Tc :: Grinding Sound From Front Left Tire
I am getting a grinding sound from what sounds like the front-left tire of my car.The car is a 2006 Scion tC - manual transmission.
It gets worse as the tire speed increases (not the engine speed and irrelevantly of whether the car is in gear), and seems to get worse when I turn left. I relaced my tires about two months ago and it started a few weeks later and seems to be getting worse.
Ford F-150 (2004-2008) :: Grinding Sound Coming From Right Front Side Related To Axle
I have a 2004 F150, 5.4L V8. A few years back I was in an accident when someone slammed into the front of my truck. The right front wheel & tire took the brunt of the accident. I thought the repair shop had everything back to normal until recently I occasionally have a grinding sound coming from the right front side, seems to be related to the axle. It doesn't do it all the time just at random while I'm driving. The only solution I can find is to pull over or slow my speed to a crawl. Once I slow down enough or turn my wheel one way or the other its like something SLAMS back into place. I had it looked at by a local mechanic and they couldn't find anything wrong. Could it be something in my right front axle?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Grinding And Metal Chewing Sound Coming From Front Axle Or Close The Wheel Hubs
I have 1999 F350 7.3 Crew Cab 4WD. I took it on a 4 hours trip towing a trailer to haul a small tractor on it. after 3 hours of driving, I started hearing grinding and metal chewing sound coming from the front axle or close the wheel hubs. It was awful, terrible, ... you name it!!! I had to continue or I will lose the tractor I paid for already. The sound was coming for 1-2 seconds each 500 feet or so. It never stopped or changed. I pulled over to see what's going on and found the following:
1. Left shock is leaking badly
2. Right locking hub is gone (not sure if the truck had one before). I bought this truck last year, but I never had to use 4x4 and I know the 4x4 motor by the transfer case is missing and the nipple on the transfer case is set to the 2wd position so the front drive-shaft does not turn.
I took the front shock off and continued to drive without it, the noise did not go away.
I pulled over again and this time I noticed that the dust cover on each end of the front axle is missing too. I have never worked on these axles before, but I jacked one side, and sure enough, gear oil was leaking from the other side. I took the plug off the front differential and stuck my finger in it. I felt a creamy brown-greenish stuff in the differential. The consistency is like mayonnaise or thin peanut butter. I put the plug back on and went to pick up the tractor because I did not want to miss it fooling around with the truck on the highway.
The truck made it there and back (almost 5 hours total after the break down). The sound never stopped every 500 to 1000 ft.
After getting home safely, I took the other locking hub off, and took it for a test drive. I did not hear the noise, but now my right brakes are locking.
I took of the wheels and saw that the retaining snap ring (C clip) for the front axle on the right side came off by hand. I took the washers behind it off. Took the calipers and brackets off. I have never done front axle rebuild. I am not sure what has been damaged and what's still good.
Right of the bat, I know, at least, I need 2 shocks, one brake caliper and pads.
My questions are:
1. Is it possible to take the front axles off on both sides and make it 2wd for now until I have the money to rebuild the axle?
2. Could I use the same hubs? or they are most likely damaged and how to tell?
3. How to tell if the differential is damaged/needs rebuilding?
4. How to tell if the axles/spindles are damaged?
5. Is there a step by step tutorial to rebuild the axle with all seals, bearings, ...etc? How hard is the job for a hobbyist? I do most of my repairs myself, and I was lucky at 36 years old, I never had to rebuild a differential.
6. What else I might have damaged in the process of driving it that long with the noise? How do I tell if I did?
Civic - Honda :: 1998 - Knocking Sound From Left Front Axle Area?
1998 Honda Civic EX, automatic transmission, 145K miles. Purchased three weeks ago.
Newly purchased used car has a knock emanating from the left front axle area. It's a rotational thumping/knocking sound that occurs about every 360 degrees of the tire rotation and only in forward and backward full-lock left turns. The car also has a small vibration/wobble in the left front. It's been narrowed down to the CV half axle outer bearing. What is puzzling is left front knocking from the outer CV joint is usually associated with full-lock right turns (and vice-versa) However, the left front knocking/thumping only happens as stated above (full-lock left turns).
Recent front end parts replaced:
1) Left front hub assembly and bearing
2) Inner and outer tie rods on both left and right sides
3) Front left caliper
4) New front brake pads on both left and right sides
5) Automatic transmission 3 x 3 drain and fill + Lubegard red
Ford - Explorer :: 2003 - Grinding Or Humming Sound Coming From Left Driver Side Front
Alright so I'm having a problem with my 2003 Ford Explorer. I've recently noticed that when I get to above 40 mph, if my steering wheel is straight, I hear a loud kind of grinding or humming sound coming from my left driver side front. If I am going about 65 mph, it gets even louder and if I crank the steering wheel to the left, that's when it really gets noisy but as soon as I crank it to the right, the problems gone. When I do hear the hummin sound, I can feel it in the steering wheel. I have replaced al of the tires and it didn't work. Also, the car slightly pulls me to the right.
View 10 RepliesChrysler - PTCruiser :: Clicking Sound Coming From Near The Left Front Tire
I have a 06 PT cruiser with about 70k miles.About a month ago a small click started near the left front tire. I thought it was a pebble and checked the tire to find none. It increases volume and frequency with speed. There's no vibration or grinding. Brakes are good, and I just had the bearings replaced about 6 months ago.
View 5 RepliesFord - Focus :: 2012 - Grinding Noise When Turning Steering Wheel?
Ford Focus 2012 - 25,000 miles
There's a loud grinding noise from the front end of car when I turn the steering wheel... even when the car is off and in park.I can post videos of the noise if needed.
Prius (2001-03) :: 2002 - Loud Grinding Sound Coming From Left Front As Car Stopped
I applied brakes while car was moving slowly, less than 10 mph, and heard loud grinding sound coming from left front as car stopped. Shifted to reverse and car barely moved, less than 1 foot, which was accompanied by the loud grinding sound, then stopped. I could find nothing interfering with the wheels but did find pieces of brake pad on the ground along the path the left front wheel had followed. The left front wheel appeared as if the calipers were holding whatever remained of the brake pad and/or backing tight against the rotor. brake pad fell apart on 2002 at 43,561 miles...
View 19 RepliesFord - Focus :: 2004 - Grinding Noise From Front Passenger Side
I've had a grinding noise coming from the front passenger side, sounds like the wheel area of the car, for many months. I've driven thousands of miles on it like this, mostly because I'm broke and the car otherwise runs fine, but also because when I've taken it to mechanics, they are stumped.
I took it to a shop about a year ago and he had it for a week, had different specialists look at it and ruled out anything mechanical (wheel bearing, etc.) In the end, he threw up his hands and didn't want to give me any more free labor for his non-diagnosis, and thought he ruled out everything but the transmission. I took it to a transmission shop recently, and the guy ruled out right away that it was the transmission. He tried to diagnose the problem and was stumped too.
Here's what it is doing. It makes a grinding noise around the front passenger wheel when I accelerate. Only when I accelerate. It seems to be more active when it is cold, and after I've been driving the car for about an hour or so, it goes away. It used to only really happen when taking right-hand turns, and that is still when it is at its worst, but now it does it anytime. However--some days it is very bad and some days very light. One day--of course the day I designated to take it to the shop--it stopped altogether and drove like new. Just until I got it home. It is worse in low gears, and used to only happen in first, second and third, but now on an active day I can hear it on the interstate in fifth gear.
The shops I've taken it to can't seem to figure out what it is. Reading threads online, I've learned that people with similar problems found the problem was a bad passenger side motor mount. I have the car at a new shop right now, and I asked them to replace the motor mount, even though it looks fine. I had a long talk with the mechanic there today and he seemed a bit skeptical, but thought it was a possible solution.
Should I spend the money on a motor mount even if it looks okay? (I've also read that the Focus mounts look fine from the exterior when they are bad because they have a gel interior that busts). Especially if this doesn't work, I'm going to be back at square... um, zero.
Ford - Focus :: 2000 - Gurgling In Front Left Side Of Car For Some Time
My 2000 ford focus has been gurgling in the front left side of the car for some time. my mechanic has had it twice for this repair and says it is just low antifreeze but the gurgling remains. What it could be? Just the sounds of an aging car?
View 3 RepliesFord F-150 (2009-2014) :: Grinding / Ratcheting Noise In LH Front Axle When In 2WD
Wife's 2010 F150 4x4 85000 KMs makes grinding / ratcheting noise in LH front axle when in 2 wheel drive. Mostly when turning left some times when traveling straight never when turning right. Never makes the noise when in four wheel drive. I am suspecting the auto hub is the issue but wonder if others have had this trouble ?
View 5 RepliesFord - Focus :: Left Front Brake Makes A Scrubbing Noise In The Rain Only
When it rains the left front brake makes a scrubbing sound and has a small vibration. After using the brakes once or twice it goes away. It sort of feels the the rotor is warped. But, it only happens in the rain and then goes away. I had the dealer look at it several times since I bought this car in 2008 and they claim they can't find anything wrong with it.
View 5 RepliesFord Excursion :: Pop Noise In Front End / Left Front Wheel Grinding
Driving at hwy speeds and head a pop noise in front end. Stopped and couldn't find anything, heard it a couple of more times, still nothing found, now I have a grinding noise left front wheel. What the issue may be. 2001 Ford EX 4X4.
View 6 RepliesCamry 2012+ :: 2016 - Knocking Sound Like Ping Pong Ball Coming From Passenger Side Front Tire
I own 2016 Camry special edition, and while driving i hear something knocking sound like ping pong ball sound coming from passenger side front tire, feels like shock is not working properly, in warm weather (over 60F)it drives better no sound or anything, what can it be? Is it because of 18" tires?
View 2 RepliesFord Excursion :: Clicking Noise Coming From Front Right Side Tire - Excessive Play In Axle
I have had a Clicking noise on my 2000 x 4x4 since 6 months coming from the front right side tire noticeable over rough roads or over bumps and I went on a journey starting with ford dealer to almost all well recognized service centers and every body says your front suspension is ok and no one seems to know where it is coming from. I thought it was my hub bearing since it fails almost every year but when I was changing the bearing, I noticed a big Excessive play in axle.
See video : My AXLE Shaft - YouTube
Also I noticed oil mixed with grease the grease is prawny with a reddish sort of color or that is some thing else.
See photos ....
Any way after replacing the hub Bearing with a used one and butting every thing together I went on a test drive. Noticed that the vehicle drive line is not right the car seems to wonder and the noise still there so i didn't get far i came right back and park my x then a funny burned oil smell was present.
Is it some thing i did wrong or is it bad situation gone worst ?
Items Checked Or Replaced In The Last 4 Months ( trying to fix)
Tie Rods. Ok
ball joints. Ok
suspension front and rear. Ok
Front stabilizer bar. Ok
control arm bushings. Ok
stabilizer bar bushings Ok
steering linkage. Ok
brake pads. A new front set installed
Rotors . Both front changed with oem parts
body mounts + sub-frame mounts. Some replaced
shock absorbers . New 4 set installed
- Rear Monroe 911176 Reflex Light Truck Shock Absorber
- Front Monroe 911175 Reflex Light Truck Shock Absorber
tires. Replaced with a new set off four
Hub Bearing. Second hand (that's when I saw it)
Spare Parts waiting list (Ordered):-
O ring ord part # 4C3Z-1K106-AA
(knuckle seal) (F81Z-3254-CB).
and some other dust seals which i can't recall.
I am looking for how to fix axle play and get red of the noise. (this is a video from you tube for clearance)....
F250 wheel bearing, is this bad or not? - YouTube
Ford Super Duty (1999-2016) :: 2000 F350 - Grinding From Front Axle When In Gear / Under Load
The issue is with my 2000 F350 crew longbed V10. Other than a BTS trans put in a little over a year ago, and FoMoCo motorsports headers, the whole truck is bone stock. Oh, it has that fantastic auto-hub thing with the fake locking hubs and the little switch on the dash (I'd love to convert it to a manual shifter...?). 174k on chassis, so things need to be done, 40k on engine, 3k on BTS 4r100.
Yesterday I was running around town, made a stop, and when I started moving again got a loud grinding from the front axle. Thought maybe I'd picked up a rock in a caliper or something, so I jumped out and checked everything, no joy. Moved forward, there it is again. No vibration, but loud enough (or telegraphing enough) to hear clearly in the cab. Let the truck roll forward, popped in to neutral, noise fades away. Back in to drive, there it is. So, now I know it's trans/t-case/driveshaft/related. I recently put new vacuum lines in, checked all the connections, and pulled, cleaned and lubed the hubs.
And since the trans is a nearly new BTS that is working just find, I'm narrowing the search to the hubs, drive shaft, t-case.
Get home (noise abates above 30mph, or everything else drowns it out), crawl under, and find the front driveshaft is locked. Ok, stuck hub? Pull out both the fake locking hubs, and now the shaft turns. I can turn each front axle by hand at the u-joint, and I kinda hear a faint grinding on the right side (will bad needles make noise only under a load from the trans and not coasting in neutral?), and when I swing the drive shaft around the left axle moves, right doesn't, etc etc.
I'm going to pull the drive shaft today and check the U joints, and drive a bit to see if the noise is still there, but I am thinking I might have some bad needles on the pax side axle...
Ford 7.3L Power Stroke (1999-2003) :: Front Left Outer Axle Shaft
Can I re-use this shaft or is that ring around it no good. The ring is around where the bearing sits. It is a circumferential hump all the way around.
View 14 RepliesPrius (2010-12) :: Grinding Noise Near The Front Axle
So I was driving yesterday and I hear a grinding noise near the front axle. I pull over and a plastic panel is hanging off near the front of the car. I go to the family mechanic to have him put it back on, and since one of the clips are missing, he tells me to go to the dealer to get a clip and have them fasten the panel.
This morning I go to the dealership. The service advisor gets me right on a lift and comes back about 20 minutes later with a slip of paper. He tells me that the piece is the door from the under body plastic protection that protects the oil reservoir. There are no sides of it that seem to have been ripped off a larger piece, just holes to be screwed in. He tells me the whole entire piece needs to be replaced, end of story. He did not offer warranty coverage (I have 20K on the car) and was not interested in speaking to me further on the topic. The parts desk pulled up a diagram of the car and showed me the panel as part of one big piece underneath that needs to be replaced.
I am going to seek out another dealership on this, but I wanted to pose this to you all as well. First, do I even need to replace this small piece of thin plastic? Second, if I do, can I buy just this small piece and not the entire under body panel. I noticed some threads about the poor design of the oil door, and perhaps this is what this is? I do not have access to a floor jack or garage, so all of my service (free toyota care) has been done at this specific dealership. Here is a pic of the piece.
Ford Super Duty (1999-2016) :: 2000 - Front Axle - Hub Makes A Slight Metallic Grinding Noise About 1/2 Way Around
I am in the process of replacing the front hub seals so my ESOF works again. I tested both front hubs with a mityvac and neither one of them holds any vacuum at all. All the lines are good, and the pump and solenoid seem to be working fine.
I have the driver's side apart and I have a couple of questions.
What's a good source for the vacuum seal? I've checked rockauto, riff raff, and diesel o-rings. Diesel o-rings has it, but the description says it's only for 2003+ Excursions so I didn't order it.
There is no yellow o-ring anywhere on the hub. I assume that someone forgot to put this o-ring back in and this is why I don't have ESOF? I guess what I really want to know is that there isn't some 2000-specific thing where there's no o-ring, right?
After I got the hub off, I spun it around on my workbench and it doesn't sound good at all. It makes a slight metallic grinding noise about 1/2 way around. I assume this isn't normal? AFAIK these are all original parts - but the missing o-ring means to me that someone already had it apart.
There was a lot of water intrusion and rusty colored grease but nothing was dry, the needle bearings were intact and the shaft isn't scored at all where the bearing rides. I'm hoping new seals and good cleaning and it should be good as new. And then it's off to the next side.