Elantra HD (2006-10) :: Gas Pedal Stuck On The First Push Down Only
I've a wired problem, my Elantra 2008 gas pedal is being stuck on the first push down only, when the car parked for more than 3 hours for example, the first press on the pedal i feel it very hard then it accept the pushing with a sound as if something is stuck and got released, after the first push it become very normal till i park it again.
I greased the pedal but noticed it may be the throttle cylinder at the engine where the gas wire is going around, i tried to accelerate the engine by turning this cylinder and it is being stuck at the first then is loosen, i tried it spray it with WD40 but it is the same.
Ford - Focus :: 2000 2.0 - No Response Intermittently When Depressing Gas Pedal
I bought my girlfriend a 2000 Ford Focus with 150k Miles on it to drive for the summer in Oregon. The car is physically in great condition with no noticeable leaks on it. After a week or so of driving, my girlfriend complained that a couple of times she would be driving the car and while going up a hill "nothing would happen" sometimes when she punched the accelerator. I asked her if the engine revolutions were going up and if the engine made a "vroom" sound (to try to see if the transmission was slipping) and she said it did not.
On a long trip driving from Seattle to Portland, she was driving again and we were climbing a long hill and she suddenly complained that "nothing was happening" when she punched the accelerator. She panicked and pulled off to the side of the road quickly. There was no shaking or vibration. I did not hear the engine wind up when this happened... so I am assuming the tach was not going up when she depressed the gas pedal. I opened the hood and looked inside and seeing nothing obvious, I switched to the drivers' side. No codes were thrown. I drove the car up the rest of the hill and to a flat area and we let the car cool off for a few minutes. I drove the car for the next 75 miles to Portland without event. When we got to her grandparents house, I changed the spark plugs (which were pretty fouled up), and changed the fuel filter (which actually looked pretty new.) and it seemed to satisfy her for awhile. Being that I havent experienced the issue, I just assumed she is not used to driving a small hatchback with a fairly wimpy engine.
In the meantime I had the entire front end redone, control arms, etc and alignment because she had had a slight shake...which is unrelated here but i figured I'd mention it. So, the other night she calls me on the side of the road, slightly shaken. Her latest incident was as such: at the bottom of an on-ramp to the highway, she punched the accelerator and "nothing happened" when she hit the pedal. This time the check engine light briefly came on, and the "OIL" light came on. She was able to pull off to the side of the road somehow and then pull to an exit. She turned the car off and let it sit for 5 minutes.
Here's the weird part: She started it up and claims she put it in "Drive" and pressed the gas pedal and nothing happened and the car actually started creeping backwards. She hit the brake and turned the car off. She started the car and drove away 5 minutes later without incident and drove it 20 minutes home. She said her gas was very low when this happened, close to the gas light coming on.
She took the car to a reliable mechanic in seattle the next day, and they said there was no issues and they thought the car was actually in great shape. Unfortunately no codes were logged and no codes have been logged at all! My only other weird observation about the car is that the tach seems to fall kind of quickly after acceleration... almost comically compared to my volkswagen 1.8 which has a gentle rise and fall to it. It kind of bounces up and down but the ride is smooth. Random, but i figured i'd mention it
Should she just make sure to keep the gas level above low/empty?Should a fuel pressure check be on the docket? The previous owner claimed the timing belt only had 25k on it, but he could have been lying.
Ford - Focus :: 2001 - Intermittent Pulsation In Brake Pedal
I noticed a pulsating feeling when I applied the brakes in my 2001 Ford Focus. I figure that it might be warped rotors, but after driving the car for a while, it seems to have dissipated. The car was sitting around for a few weeks. I read that it could just be rust buildup, but I feel that would require more than a few weeks of sitting around. Is there any way to check for myself, short of taking off the rotor?
View 3 RepliesFord - Focus :: 2007 - Clutch Pedal Return Spring Broke?
So, I think that my clutch pedal return spring broke yesterday in my Focus 07 Hatchback when I was at a stop sign. I let out the clutch and felt and heard something like a small cable breaking. Now the clutch still operates fine, but it is softer than before. If it is indeed that little spring, can I still drive it around for a few days until I can get it to the dealer?
View 2 RepliesParkingbrakes - Ford - Fuses - Focus :: 2003 - Stuck In Park / Release Does Not Trigger On Startup
I have a 2003 Ford Focus that over the past few days has found itself stuck in park. When I start the engine, the release doesn't trigger and I have to use the manual release in order to move the gearshift level to drive. The same happens if I've been driving, stop and put it back in park--the release button is locked and I have to use the manual release.
My owner's manual suggests that I may have a blown fuse or my brake lamps may not be operating. My brake lamps are, so I'm looking to check the fuses.
My confusion now is coming from which fuse I need to check, and whether its in the fuse panel or power distribution box. The manual has a handy chart showing right where to look, but I don't know what I am looking for.
[URL] ....
I'm not too saavy with working on vehicles, should I just take it to a mechanic or is this something I can check and replace myself if blown?
Ford - Focus :: 2001 Occasionally Stalling / CEL On - Steering Wheel / Gas Pedal Lock Up?
I purchased a 2001 Ford Focus 7/17 from a Ford dealer. While my daughter was driving, at a left turn, the engine light came on, the car stalled, and the steering wheel and gas pedal locked up. A friend did a computer scan and said the code came back that 2 sensors, the crank shaft and cam shaft sensors, needed replaced. So we had them replaced.
About 4 days later, while driving home from school, on a right turn, the car broke down again on my daughter. She said the symptoms were the same, engine light came on, car stalled, the steering wheel and gas pedal locked up. So we had it towed to a local Ford service department. They said the ignition coils needed replaced and the valve cover gasket would eventually need replaced (per the mechanic, this wasn't directly related to the issue but a small leakage was found). So we let the Ford mechanic replace the coils and the valve gasket cover. They ran several tests and put 20 additional miles on the car without failures or issues, scans came up clean.
So while driving to school this morning, on a u-turn, my daughter experienced the issue again....car stalled, engine light came on, steering wheel and gas pedal locked up. After sitting a few minutes, the car started up so she drove it home and hitched a ride from dad to get to school.
Focus :: 2013 - Ignition Key Stuck In Switch And Will Not Release
My wife recently purchase a 2013 Focus SE 5 door and a few times now the ignition key "sticks" in the switch and will not release. She has to turn it back on and off a couple times to get it to release.
View 1 RepliesGolf IV R32 :: Pedal Cover Came Off Of Gas Pedal And Got Stuck
I was leaving a training class today and the cover on my gas pedal got stuck, I came close to a truck. (new car + big truck = not good) i stomped on the gas a couple of time and got it to release. I was not in a high traffic area.
View 24 RepliesFord - Focus :: 2001 - Brake Pedal Feels Hard / Transmission Hard To Shift From 1st To 2nd Gear
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
Ford - Focus :: 2006 - Secondary Air Pump Failure
I have a PZEV (Partial zero emission vehicle) 2006 Focus. Recently, my car threw the check engine light. Looked at the two codes, found out it was for the secondary air system. I pulled the car apart, removed the pump, checked that the pump was indeed receiving 12v (checked with a multimeter) with ignition-on-engine-off. I couldn't feel, or hear, the pump spinning. Figuring it was the source of the problem (as opposed to a clogged hose), I replaced the relay, thinking that perhaps it was on its dying leg. That didn't work. I next replaced the pump, which also didn't work. I can't even hear or feel the new pump running with ignition-on-engine-off.
I "reset" the codes, or so I thought, by disconnecting my battery for quite a few minutes. During the first startup, the check engine light isn't on. Starting up again though later in the day, the light returns. The engine does run a bit rough when cold without the pump malfunctioning for the first few brief moments.
Is the pump supposed to be powered and running for the entire time ignition-on-engine-off (I assume so since it is receiving 12v). How loud should these guys be? I would have thought I would be able to feel the motor spinning or hear something....
Ford - Focus :: 2006 Will Not Hold A Start When Cold Outside
My 2006 focus just turned 100,000 miles. Last few months as it started to get cold outside its had issues with not "holding" a start. It seems to make all the normal sounds but won't continue to run. It is progressively getting worse, ie: more frequent and takes more tries to get it started. Yesterday I tried repeatedly and it wouldn't start until I gave it a LOT of gas-this is the worst its been. Previously it would either eventually start after repeated tries or with a little gas. Even on unseasonably warm days its happening now. Both autozone and tireman say the battery (2yrs old), alternator, and starter check out fine.
After lots of online reading here's what I've tried/paid attention to in hopes of narrowing it down.
-Changed spark plugs
-Fuel injector cleaner
-Spare key
-Don't notice security light flashing when it happens or any other random electrical issues
-No strange idle fluctuations
Once its running its fine and seems to start ok for next couple tries even at cold start. Trying to narrow down from IAC valve, PCV valve, throttle position sensor, wiring, ignition switch, fuel pump, etc. Can computer codes read even without warning lights? I have noticed for quite some time that idle has a slightly rougher sound (nothing obvious) but this seems to comes from muffler end and its been in for standard service and never been mentioned as an issue...? Its never stalled at idle or sounded like it was close to stalling/strictly issue with getting it going. I'm trying to determine if its logical that repeated attempts or giving it gas build up more fuel pressure? Or more logical that lots of gas is pushing open something thats clogged up?
Ford - Focus :: 2006 - Brake Auto Applying Intermittently
I have 2006 Ford Focus that was recently in a small rear end crash. The airbags went off. The only damage was a front bumper and hood and plastic grill. The computer had to be reset by Ford dealer for the airbag. Since the accident the front brakes intermittently apply, not enough to slam the car to a stop, but enough to slow it down and limit acceleration. We have replaced the rotors, calipers and front brake lines. Problem still exists. Ford says the computer shows nothing (duh) and my mechanic of 20 years doesn't know what else to do.
View 1 RepliesFord - Focus :: 2006 - Procedure For Taking Off Broken, Rusted Hub Stud
I broke one of the wheel/hub studs on my 2006 Ford Focus, when I tried to take the wheel off. So, this car lived through 7 winters in Boston metropolitan area, and it has about 90,000 miles on it.
I bought the car used last summer, so I don't know what the previous owner did, but I have always torqued my wheels since I bought it. But one of them broke off anyway, when I tried to take the wheel off. I took off the brake caliper and the disc to see the condition of the broken stud. The hub and the stud seemed to have rusted together. I recently moved from California via Oregon, so I am not used to seeing a lot of rust on anything. So, I can't tell whether that is a lot of rust or just normal run-of-the-mill rust I shouldn't have to worry too much about.
I checked online and found that if a bolt/stud is rusted, and if I cannot get it loose by banging it with a hammer, I should torch it and let it cool before trying to loosen it again.
I would like to hear some anecdotes about loosening wheel studs. I went to Harbor Freight today to get a hammer. One guy told me I should get the 8 pounder with a long handle (looked to be 3 feet or longer), so it will be easier to aim and provide steady force. He said it would be like putting a golf ball. I was also looking to get a torch, and he said that I need to heat it until it glowed, so small propane bottle torch would not be enough. But he said for a relatively newer car like mine, a few taps with an 8-pound sledge hammer should be enough.
I am also concerned that I might end up breaking more stuff and have to replace the entire hub, which would be a costly proposition. How much would it cost if I took it to a mechanic?
Also, seeing that some of the other nuts didn't go in smoothly, would it do any good to replace all the lug nuts?
Ford - Focus :: 2006 - Warning Lights For Check Engine And ABS Come On Randomly
Ford Focus Station Wagon 2006 - Seems to have electrical problem. Warning lights for check engine and ABS come on randomly. Also when car is parked and temperature is low, Clock time is lost and radio stations are lost. Is there some type of grounding issue?
View 5 RepliesRanger :: 2000 Ford XLT - Clutch Pedal Stuck After About 15 Minutes Of Driving
I'll drive my 2000 Ford Ranger, 4cyl XLT about 5 miles to the store without a problem. On the way home, after a few miles, the clutch pedal will either jam at the top, or go all the way to the floor without engaging the clutch. If I wait 5 or 10 minutes, the clutch pedal will start working again for a short time.
If I feel the clutch pedal starting to misbehave, if I ride the clutch and don't release the clutch pedal all the way, and if I don't push the clutch pedal all the way down, I can keep driving the truck. As soon as I release the clutch pedal, it will jam up again, or the clutch pedal will go all the way to the floor without engaging the clutch. I don't like riding the clutch, but that seems to be the only way to get home once the clutch pedal starts jamming.
It certainly seems related to the engine warming, or heating up. Sometimes, after the clutch jams up, I'll wait 5-10 minutes and the clutch pedal will start working as if nothing every happened. So, it can't be strictly a hot engine, hot clutch fluid issue, right?
What would you attempt to replace first, the Slave Cylinder? The Master? Changing the fluid? Shooting the truck!?
Ford Aerostar :: 1996 - Noise While Depressing Pedal - Brake Stuck?
96 Aerostar Cargo 6 cyln. Auto.
There is a noise coming from what sounds like the rear passenger side wheel. Also, when you put it in drive and release your foot from the brake the van stays still. You have to push the gas to get it moving, like the brake is holding it. If you are going very slow on a flat surface the van will eventually stop instead of idling forward.
I have removed the wheel, it does turn hard. Pulled the drum (was very hard to remove). Had to move adjuster to remove drum. Cleaned inside, inspected the brake shoes, put drum back on, etc. I am pretty sure that brake is causing resistance. How to resolve it?
Ford - Focus :: 2006 - Size Of Rear Drum Brake Bleeder Valve?
I replaced a brake cylinder on my 2006 Focus rear drum brake. Now, I need to bleed the brake fluid, but I can't find a wrench to fit the nut.10mm is too small and 11mm is too big. What's going on? Could it be the rusted nut has grown in size enough to make the 10mm wrench too small? Or, is the nut standard?I know the drum bleeder nut I know the front disc brake bleeder brake is 10mm. So, I am thinking the rear should be metric, but since it's drum, I am not so sure. What the size is?
View 13 RepliesFocus :: 2000 Focus SE Running Rough Idle Then Stalling
my 2000 focus se, 2.0L SPI, with 82k began to recently run rough at idle then progressed to stalling at longer lengths of idle. The condition starts once the engine warms after 2-5 minutes. I 1st tried gas treatment. I replaced the ignition coil as suggested in the other threads, but it has not improved the problem. I had the fuel pump recall-replaced 2 years ago. I would guess that a bad fuel pump would exhibit loss of power at all engine speeds? Before I proceed to replace plug wires and plugs.
View 14 RepliesCamry :: 2003 - Clutch Pedal Stuck
My wife has a 2003 Camry that we had to replace the clutch last year. Now her clutch pedal goes to the floor and does not return.
View 2 Replies