Ford Transmission :: 1999 F250 4x4 Automatic - No Forward Gears Only Reverse?
I recently bought a decent looking 1999 f250 4x4 5.4 auto. It has no forward gears and will only move in reverse. I topped off the fluids and have found no leaks so far the cooler lines are crusty but dry. I am gonna need to swap this thing out or do some more trouble shooting if there may be a non rebuild issue to solve.
View 4 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 F250 Truck Has Always Had Difficulty Starting Cold
2001 F250 7.3l 294k miles
Ok so truck has always had difficulty starting cold since I got it about 12k miles ago. Replaced glow plugs, that made things slightly better but still no start unless temp gauge was in that first line above the C. Changed to Rotella, immediately after oil change starts better and at slightly colder temps.
Since getting the truck when you turn the ignition on you can hear a 'whistling' type noise which I believe is the fuel system pressurising. That used to last as long as the chimes did when you first turn the ignition on. More recently it lasts a lot longer.
Towed recently and had intermittent check engine light - believe this could be HPOP related, haven't checked codes yet as we're on vacation. No oil in the valley. But I do have a little oil carry over in the turbo intercooler pipes.
Truck slightly sluggish at setting off initially and then picks up reasonably well when not towing but my Dyno says I'm putting a bit more pedal to get the same performance from say two months ago
Pretty sure injectors haven't been changed since truck was new but can't be absolutely certain as there is no history. I was surmising this is probably both a HPOP and injector age issue but only from what I've found searching...
Ford Super Duty (1999-2016) :: Automatic Transmission Swap 2000 F250 To 2003 Model?
I have a 2003 f250 4x4 with a 5.4 motor the automatic trans is shot. I can get a replacement trans from 2000 f250 4x4 with the v10 motor. I tried my best to research it bell housing supposed to be the same so it should fit. But I'm not sure what they changed in those years internally or electronically.
View 2 RepliesFord Super Duty (1999-2016) :: F250 - Big Power Loss Momentarily
I have a 99 F-250SD with 5.4 automatic that just all of a sudden started running unevenly at random times, but frequently. There is a pending code P0300 Random/multiple cylinder misfire. I have had the truck for 12 years and it has run perfectly for the last 10+ years and just started this problem, it did not come on slowly but all of a sudden. I have seen on here that some people say that 90% of the time a PO300 is a bad cop. I replaced the plugs 60k miles ago when I had a bad coil on plug 10 years ago that did not set any codes, but this seems very different that more than one cylinder seems affected, like maybe 2 or more cylinders are not firing momentarily.
There is a big power loss momentarily while it happens, but doesn't happen for long. The fuel pressure stays pretty constant (30 psi at rail) even while it happens, and it can affect the idle as well as while accelerating or cruising at speed. I cant imagine more than one coil on plug would be skipping at the same times or fail at the exact same time, but maybe having only one bad cop could cause this much hesitation? Does the code that indicates random/multiple cylinder misfire rule out only one bad cop? It just seems like running on 7 cylinders wouldn't be so noticeable. Could a sticking egr valve cause unevenness at idle and higher rpms and set a P0300 code? Would checking manifold vacuum be they way to see if egr valve is not working correctly.
Ford 6.7L Power Stroke Diesel :: 2012 F250 Diesel Frequently Stalls Momentarily After Touch The Brake
My 2012 diesel frequently stalls momentarily after I touch the brake. This is very annoying as I drive in heavy traffic and often have to touch the brake then accelerate to merge into freeway traffic. The dealer service department said this was a 'feature' and not a flaw. Is there any way to eliminate this issue?
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2004 F250 Stall After Start When Backing Out Of The Driveway
I have had literally no issues with my 2004 F250 Super Duty. Went out and started the truck like every other time for the past 13 years. Started backing out of the driveway and burped the throttle and it just quit??
I put back into park and it rolled over for about a minute and finally caught. When i put it back into gear i had zero throttle response. I have a NOx sensor fault code and and EGR fault code. I replaced the FICM 2 years ago.
Ford 6.7L Power Stroke Diesel :: 2015 F250 Bucks When Backing Up Only Noticeable In Cold Weather
Our temps have hit into the -18 to -25 Celsius... I have noticed that on 3 different occasions now that the truck feels like its locked in 4wd when I reverse out of my drive way.My Truck is an F250 Crewcab with 4800 miles
This all started with the cold weather. At first I thought my 2 yr old was turning switches on while he was up front one time, but it happended again the following morning taking my 5yr old to school...
I back up up about 20 feet and then make a fairly sharp 90 degree turn and then all the way down the driveway to the street...its really noticeably on the 90 degree turn..once I turn to go forward it still seems jerky...same as having 4wd engaged on dry surface while turning..
After a little bit of driving it seems to go away...also keep in my mind that the 4wd switch has never been touched at anytime at all...we have a lightly snow packed driveway but my traction is still fine to where 2 wd is all that's needed
Could it be something in the rear diff "catching and releasing" for lack of a better term ?
Locker issues, clutchpacks...?
As I am typing I also remembered making a right hand turn on dry pavement and it felt like the rear end slipped a bit and then caught again, much the same way it would fell as if you hat one tire on a small patch of ice and slipped as ya took off and then caught as it hit the dry pavement...
Ford Super Duty (1999-2016) :: 2003 F250 - Front Hubcaps Backing Off Slightly
I've been noticing that one of my front hubcaps has been backing off slightly. I tap it back on and it's good for a while. But lately I'm noticing that I have to tap it back on more often. I took it off today, thinking that I might need a new one. The part number on the inside is IC34-IA096-AB. It's on my 2003 Ford F250 4x4.
I pulled the opposite cover and tried it on the side I'm having trouble with and noticed the same thing. Upon further inspection, I noticed that the chrome plated trim piece that covers the steel rim has tabs that should be flat to the rim. I'm referring to the area where the trim piece ends, near the lug nuts. On the one that I'm not having trouble with, it's flush/flat all around. But on the one I'm having trouble with, some of the ends are not flush to the rim. That is why the hubcap is not seating in those areas. I can see the gap and I can also push down on that section. It's almost as if that trim piece is separating from the rim? I tried using a punch and giving it a couple of whacks with a hammer, but it doesn't press it back to being flush with the rim.
Why would the end of that trim piece that covers the whole wheel lift up on the ends? Is there a way to get it to sit flat?
Ford Super Duty (1999-2016) :: F250 - Thump While Backing Up - Loss Of Reverse And Park
I was driving my 1999 F250 5.4 Triton last week, after noticing a thump while backing my small boat down the ramp (sounded like u joint) I went and parked. When I got back in the truck it starts fine but when I shift into reverse, it's staying in drive, anywhere I put my shift lever..... It's in drive! I even noticed that even all the way up into park it feels like it's in drive, but with something holding it back. If I give it gas while in park it will go forward! I have tightened the two torx screws under dash, pulled cable off and tried shifting by hand (clicks like switching gears, but still in drive) pulled pan, everything looked good there, fluid is nice and red, smells good, no metal in pan? It's the 4r100od tranny.
View 7 RepliesTouareg :: Rear Wiper Always Sprays Washer Fluid?
How do I turn on the rear wiper without it spraying the window with washer fluid? I've followed the instructions in the manual for using the rear wiper, but very time I turn the wiper on it sprays the window with washing fluid. I don't need washer fluid sprayed on the window if the window is already wet from rain.
View 11 RepliesFord Transmission :: 4r70w - No Reverse When Backing Out Of Parking Space Or Shudder In Reverse
2000 F150 Lariat, XC, 2WD, 5.4L, 4R70W
I don't know if this all started right after I got back from towing a 3500# lathe + 2000# trailer back from Texas a couple weeks ago or if there might have been some slight symptoms before. I do know that this really got bad a couple days ago and I haven't driven the truck since then.
So, here's what is happening. I noticed a few days before that when I would back out of a parking space, the truck didn't seem to go right into reverse. It was as if it was in neutral, but as I was reaching to jiggle the gearshift lever, it would engage and I could back out just fine. All forward gears, and shifting, have been fine all along, including lockup. I kind of wondered if the shift linkage had somehow moved and was on the edge of being in the right spot, so I was going to have a look at it one evening soon. Then a couple days ago, I went to back out of a parking spot at work and it wouldn't go anywhere.
Just acted like it was in neutral. Put it in drive and it engaged just fine, then back to reverse and nothing for a few moments before it finally engaged. Then, as I was backing up, it acted like you might expect a limited slip that was not slipping to behave. But, that was right before I put it in drive and went home. After I got home, I tried it out some more and found that in reverse, it just wouldn't go anywhere unless the truck rolled a little bit. I don't know if the rolling really had anything to do with it or not, but the driveway is on a slight incline, so it happened, and then the transmission would engage. But, when it did start to back up, even straight, at first it acted like it was under a load, then when it started to move, it bucked really badly. Put it back in drive and all seems fine.
There are no codes set. Trans fluid is full, and doesn't smell or look bad. I've searched for reverse shudder, and other stuff, and there are threads about the TC, about no reverse at all, and a bunch of other stuff, but nothing like this that I found.
Ford :: Automatic Transmission Sometimes Not Shift Into First Gear
I have a 36 foot motor home on a 2000 Ford F53 chassis. (similar to single axle freight trucks and school busses) After getting one set of the rear wheels partially stuck, which resulted in some spinning of that side, the overdrive off light on the shift lever began to blink and the service engine soon light came on. The fault code said, "speed sensor showing more than one mile per hour". Now the automatic transmission sometimes will not shift into first gear after stopping and has to be manually downshifted, after which, it works fine.
View 1 RepliesExplorer :: 1999 Ford XLT V6 - Automatic Transmission Removal
I have a 99 Ford Explorer XLT, V6, 4X4 with the 5R55E automatic transmission. I'm getting ready to remove / replace the transmission. Do you have to lower the back of the engine any for the transmission to clear the torque converter? Any tricks to getting torque converter off the flywheel?
View 14 RepliesFord - Fiesta :: 2011 - Automatic Transmission Won't Engage
I have a 2011 Ford Fiesta and yesterday morning I went to start it and the check engine light came on. When I tried to shift into reverse, the gear lever moved but the gear wouldn't engage. None of the other gears worked either. I turned the car off and back on again, and it was fine (the check engine stayed on, though). I have to repeat this process every time I start the car, and this afternoon it took three tries. This a low-mileage car: I bought it brand new a little over 4 years ago, and it's barely over 20,000 miles. I have an appointment scheduled with the dealership, but is this something that's going to cost me a lot of money or is it just a computer issue? One other detail: it was very very cold the night before the issue started (about -10 degrees).
View 19 RepliesFord - F150 :: 1998 - 3rd Gear Gone In Automatic Transmission
1998 Ford f150 172984 miles automatic with 4x4 runs and drives transmission is going out will not hit 3rd gear have to drive in 2nd. Is there a fix without pulling the transmission?
View 5 RepliesFord Excursion :: Can Replace Automatic With A Manual Transmission?
Would it work? I saw this on CL 2000 Ford F250 6 speed manual 2wd transmission. It says it is for 2WD but I don't think that matters because the transfer case is what make it 4WD anyway right?
I don't love automatics. With a manual trans, some new gears and the dully conversion this thing would be like driving a giant sports car. Any computer related problems?
Ford - Explorer :: 2004 - Automatic Transmission Not Engage?
I have a 2004 Explorer 4.0 4x4 with 130,00 miles that started with the transmission periodically going into neutral while driving and sometimes while stopped at an intersection. Engine running, but no reverse or drive gear. After shutting down engine and restarting, I can drive again only to have it happen soon again. I have changed rear speed sensor, throttle position sensor, dropped the tranny pan and changed the ATF as well as tranny filter.
I also attempted to replace the transmission range sensor but was unable to remove the nut that holds the shift level onto the sensor. Sent 5 hours one day.... nut will not budge. Now the shifter inside the truck does not feel the same when shifting through the gears. Now the transmission will only engage in reverse but the truck will not move. If I wait 30 sec or so the truck will move in reverse. No engagement in drive, 3rd, 2nd, or 1st.
Ford - Explorer :: Automatic Transmission - Rough Shift Into Overdrive
My 2002 Explorer LTD with 155K miles on it is in terrific shape except for a worsening rough shift into overdrive (automatic transmission) and a clunk which occurs with increasing frequency when I shift into reverse. I would love to keep the car but don't want to spend the money for a new or rebuilt transmission. There is no access for owner approach to transmission fluid - I have already looked in the manual. I would need to take the truck to a garage as I cannot do repairs myself.
View 2 RepliesFord - Mustang :: 2005 GT Automatic Transmission / Shuddering When In Reverse
I'm a proud owner of 2005 Mustang GT, 4.6L with an automatic transmission. Intermittently for the last year or so (maybe once every 3 or 4 months) its been shuddering when in reverse. Today it ramped things up a notch. :-/ The shuddering was pretty dramatic when I was trying to back out of my driveway, I shifted into park for a moment, then back into reverse, and it seemed to be ok. Then when trying to back into a parking spot this afternoon at work (in a parking garage with a small incline) it lost power almost entirely in reverse, lightly pushing on the gas just caused the car to shudder and not move anywhere. I shifted into park, and then back into reverse and heard an audible "pop" (my windows were down, but they hadn't been earlier so I'm not sure if this happened in the morning) and the car did not want to reverse. Rather than risk further damage I decided that it was parked relatively ok (90% in the space, eh good enough) so I stopped.
View 4 Replies