Ford - F150 :: Transmission Stuck In 4th Gear - How To Get Back Into Neutral

My manual transmission got stuck in 4th because of a melted oil trough sticking between the gears. I got all the plastic out, and the dog clutches/collars are "free." But, I don't know how to put the gears back into neutral. When it's reassembled, the stick doesn't work to change the gears. How can I get the gearbox back into neutral?

View 19 Replies

Ford - Escort :: 1998 - Cannot Get Idle On The Car To Go Below 2500 RPMs

I have a 1998 Ford Escort which I drove about 450 miles in frigid weather over about 8 hours in mid January. After arriving at my neighborhood and getting off the expressway, I couldn't get the idle on the car (manual transmission) to go below 2500rpm's. Further, upon taking off, the car was trying to stall, and I was forced to feather the clutch through town driving and keep the throttle up so it wouldn't stall, even with the clutch in. The weather at the time was about -7 degrees (f). The next day the weather continued, and thee car would start, jump to the same idle for 10 seconds, then drop suddenly to 500rpm, then stall out. I wrote the car off, cleaned it out over the next week, and then I tried to run the radio while doing so last weekend. I got the car to start, and run normally. I think it may be a computer issue, but it may also be the temperatures. The car has 207,000 miles on it.

View 3 Replies

Ford - Brakes - Gasoline - F150 :: 1989 - Both Rear Brakes Stuck Occasionally

I recently bought a beater '89 F-150 (I-6, MT) with the following problems:

1) Both rear brakes seem to stick on occasion--almost like there was a "check valve" on the rear brake line. When that happens, there is a "BRAKE" and "Rear ABS" light (although the light does occasionally come on without brakes sticking noticeably).

What I noticed in Haynes is that the "RABS I" system functions in the following way: a) Upon noticing rear axle spinning slower than front axle, it actuates a valve, isolating the rear brakes b) If the problem persists, it then dumps the pressure back into the main system.

So, I wonder: Is this an ABS system acting up? If I were to (temporarily) de-power the ABS setup, would it default to "no ABS," or would I need to remove the hydraulic valves from the brake lines? (Don't really want to if I don't have to.)

2) You can select either fuel tank, get that tank's level to indicate on the fuel gauge...yet it only "draws" from the front tank.

Again, Haynes says there is a low pressure pump in each tank, feeding a high-pressure pump in essentially a small "header" tank. The "dual-function reservior" has a wholly mechanical selector, and notes that "Tank switching versus gauge conflicts can occur under certain failure mode conditions."

So: I can understand that the mechanical selector can, in effect, "stick" on one tank. But what I don't understand is how it can still draw from the front tank, with the "rear" tank selected (and presumably, that tank's low-pressure pump trying to feed the header tank.)

Is it possible that the low pressure pump--while beneficial to prevent gravitation at the main pump--isn't strictly necessary to fuel the engine? Or do I have a problem with a low pressure pump that's "always on," regardless of the selected tank?

View 2 Replies

Ford 6.0L Power Stroke Diesel :: 2006 - Idle Down And Won't Get Above 2300 - 2500 RPMs?

I bought a 2006 F-350 4WD Lariat SRW with a little over 200,000 miles on it. The truck seems to run perfectly, except when pulling a load (9,000-10,000 lbs) down the interstate/highway. Sometimes, when pulling above 65-70 mph for an extended period of time (45 minutes to an hour) the truck will all of a sudden idle down and won't get above 2300-2500 RPMs (even if you put it in neutral and floor it). It's not enough to shut it down, but it won't let the truck accelerate as fast as normal. Killing the truck and cranking it back makes it go back to running normal for a little while, but the periods of it acting up get shorter after each killing and restarting. I took it to the Ford place while it was acting up, and they thought it was a turbo problem. They cleaned the turbo and said everything looked fine, but the same problem arose after leaving the shop. They've been stumped at 3 different Ford shops, but one said there's a 95% chance a new turbo would fix the problem. What might be wrong?

View 8 Replies

Ford - F150 :: Oil Pressure Dies At Idle

I have a 6 cylinder '99 Ford E150 and though it has plenty of oil, the oil pressure gauge drops and the idiot light comes on whenever it stops and comes to idle. Pressure seems fine when driving but dips at a stop lights etc..

View 6 Replies

Ford Ranger / B-Series :: Hissing Noises And Idle Fluctuate Between 2500 And 3000 RPMs

Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445

Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack

After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.

Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.

Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.

To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.

View 3 Replies

Ford - F150 :: 1997 - Engine Rough Idle For 6 - 9 Seconds Then Dies

Ive been having a problem where the engine cranks and idles, sometimes rough, then I try to accelerate and the car shakes and accelerates very slowly with shaking. I replaced plugs coil and leads and fuel filter with no effect but put on a new egr valve and that fixed the problem for 2 months. The same thing happened again and I cleaned the evr solenoid and that fixed the problem for 1 month. Then the same thing happened while I was out and while limping home it fixed itself. Now a month later, the same thing happened, but when I got home and shut it off, the engine won't idle properly (very rough) for 6-9 seconds then dies. I don't know what to check at this point. Thinking it may be vacuum related or possibly a fuel injector or magic gremlins at this point.

View 8 Replies

Prius (2010-12) :: High Engine Idle Speed - 2500 RPMs

Had a first-time issue with my car today. Background, 2010 II bought in June, just short of 15K miles, never had any kind of mechanical issue.

While en route to work this morning, I was about halfway into my 15 minute drive to work, when I noticed my engine was idling very high, I would guess 2500 rpms. It started doing it while I was driving around 35 MPH, then continued doing it while I stopped at a traffic light, and continued when I continued driving to a speed around 50 MPH. The high idle while stopped was not transferred to the wheels, so it was not a safety issue as it would be in other cars.

When I got back up to 50, curious to try something, I hit the ECO mode button and the car returned to normal. I took ECO back off and the car was still fine. I had no further problems.

I would point out that this morning was about the coldest temp that the car has experienced. Outside temp ranged from 7 to 10 degrees.

View 14 Replies

Saturn - Ls :: 1989 - Over Revving When Try To Go Into 1st Or 2nd Or Idle RPMS Jump To 4500

1989 Saturn 5 speed, 4 cyl, 185,000 miles. Just started overrevving, when I try to go into 1st or 2nd or idle RPMS jump to 4500. So not a good thing. Do not tell me to buy a new car, not in the budget, or maybe it is.

View 6 Replies

Honda - Accord :: Idle Is Fine Until Engine Warms Up, Then Fluctuates Between 1500 To 2500 RPMs

!995 honda accord, 5 speed. Idle is fine until the engine warms up, then fluctuates between 1500 to 2500 rpms. The idle control valve was cleaned- no change. Valve was also replaced -also with no change. Put old valve back on. Computer was disconnected after cleaning and also after each valve change.Would the next step be to remove and clean the fast idle thermo sensor? Also how do you check the coolant lines coming in. Anything else I would need to check, clean or replace.

View 2 Replies

Golf IV / Jetta IV :: CEL On / Idle Goes Up And Down In Neutral From 800 - 1300 RPMs

Have a 2001 wolfs-burg 1.8t, has about 220k miles on it, i know, its a lot. Right now, the check engine light has been on for a few months and the idle is very weird. It goes up and down in neutral from 800-1300 rpms and sometimes i smell gas. Also the triangle with an '!' and circle around it yellow light comes on some times now. I heard it could be MAF or a vacuum leak. A mechanic is going to check it out soon...

View 10 Replies

Accent RB (2012+) :: Idle Speed Around 900 RPMs When Put Car Into Neutral To Coast

Im curious if this is normal or not. When I'm driving and I put my car into neutral to coast, the idle speed is at around 900rpm. When I come to a stop, the idle will drop to around 650rpm. Is this a design feature? I wish the rpm would drop more to conserve on gas while I'm coasting!

View 7 Replies

Celica :: 1989 Celica GT - When Pressing On Gas / Idle Drops And Then Car Dies

My brother was the original owner then passed it on to me. I then passed it on to my younger cousin about two years ago. The car is completely stock and has never been modified. Everything is OEM.Just a couple of weeks ago I was called by my cousin saying the car broke down on her .The problem is that we took it to a few mechanic shops but they still haven't fixed it ...

Problem with car: When pressing on the gas, the idle drops and then the car dies (a scary event that happened to us and on a main road). I do not wish to bring it to another fail mechanic shop.What the shops did: changed all fluids, distributor cap and plugs, new spark plugs, and replaced air intake piping with oem piping.

View 6 Replies

Golf IV / Jetta IV :: RPMs Fluctuate At Idle And Sometimes Car Dies

So I have a 2.0 jetta and I'm having this problem where my rpms fluctuate at idle and sometimes the car dies unless I give it gas.but when I'm driving if I'm not in gear and stop it sometimes dies.

I'm getting 5 codes : P0445, P0135, P0037, P0418, P1473

I checked all my grounds I changed the 02 sensor on the manifold checked for cut wires and nothing ...

View 18 Replies

Dodge - Dakota :: 2000 - Engine Starts But Won't Idle / Just Dies And RPMs Drop

Cold start. engine starts but wont idle, just dies. rpms drop. Restart same. Must neutral drop to get going keep rpms up until engines shifts then things are fine until next cold start. Cleaned throttle, changed air filter, dry gas, injector cleaner, no warning signal, scans clean. 180k miles.

View 6 Replies

Ford - Thunderbird :: 1993 - Engine Races At About 2500 Rpm In Neutral

I'm working on a 93 thunderbird with a 3.8 in it and no check engine lights are on.The engine races at about 2500 rpm in neutral, I changed out the TPS but the idle still was way too high.

My first thought was a vacuum leak and I did find one hose that was rotted away. I then tested for vacuum leaksby spraying some brake cleaner around the intake and all the lines and fittings, but the engine stayed at a constant rpm.

My next guess is the Throttle Air bypass valve.

View 5 Replies

Ford Wiring/Electrical :: 1995 F150 - Chirp And Shudder At Low RPMs / Squeal And Vibrate At Higher RPMs

Ok, I have a 95 F150 5.0. It's sat for 6 months with the engine taken apart. I just finished putting everything back together with a new alternator. Well, I pulled a bone-head move and forgot to connect the harness when I fired the truck up. Other than not charging though, it ran fine. When I connected the harness, it began to chirp and shudder at low RPMs and squeal and vibrate at higher RPMs and it over heated VERY QUICKLY.

So hot the case was too hot to touch and the pulley smoked the belt. The engine didn't even have time to get up to operating temperature. I've had the alternator replaced twice, and this last one tested good putting out 14.5 volts. The work I did on the engine was to replace the valve springs, install a direct drive timing gear, replace a spun harmonic balancer, bypass the smog pump because it froze up, new distributor, a new ECU and O2 sensor.

View 7 Replies

Nissan - Sentra :: Stalling At Idle / Stuck And Less Power At Low RPMs

My families 2001 Nissan sentra often stalls at stoplights, has low power sometimes in the low rpm's and sometimes (though not always) chugs/jolts a bit at low rpms and has trouble "overcoming" that window and getting more power. If I give it more gas the engine seems to get "normal" at around 2500 or 3000 rpm's and then is fine.

We took it in and the mechanic said it was a bad O2 sensor or MAF sensor... can't remember which. We tried replacing the MAF sensor but it still has the problem. We have heard that we may need the computer re-set somehow or made to recognize and sync up with the new part. As we call around this is very expensive just to make a part that is already installed work. Is this necessary? What's the next, cheapest, step.

View 3 Replies

Ford - F150 :: 1989 - Chokes On Startup / Shudders While Driving

I'm a new owner of an '89 F150. It's a four speed manual trans, 4.9L 6cyl. This is my first truck and I bought a beater in hopes of learning while I fix it up. I have minimal experience (biggest repairs have been replacing disk brakes on a previous car and replacing the EGR valve on this truck), but I want to learn more.

The truck has a bypass switch and the forward fuel tank was removed. Both of these modifications occurred before I owed it. Also, the clutch is a bit grumpy. Sometimes I'm unable to get it into first (I usually "granny start" from second), and every once in a while it doesn't want to go into reverse.

When I bought the truck, it would just choke and cut off after driving for 30 minutes or so. It would restart after cooling down. My mechanic said it was a problem with the fuel pump and replaced it, and that fixed that problem.

After that, the truck began to have trouble starting. I would flip the bypass switch and the engine would rev up, then drop RPM's quickly until choking off within a couple seconds. When I flipped the switch again, it would start up fine. It would run fine after that.

A mechanic recommended having the fuel injectors cleaned. The fixed the problem for about a week, then it started again. A friend of a friend who has a home garage suggested a vacuum leak, and we found a leak in the EGR value, which we replaced.

Replacing the EGR valve fixed the problem again, for a couple days, but it came back. Meanwhile, immediately after the EGR valve was replaced, a new problem started. Periodically while I'm driving (I haven't been able to detect any pattern), the engine will just shudder or choke a bit. It feels like it's threatening to choke, but it never actually does. Once it starts, it typically does this every couple seconds until I shift gears.

I'd really like diagnosing what might be causing the choking when it starts and the new shudder when driving. I realize it could be a number of things.

View 6 Replies