Ford 7.3L Power Stroke (1999-2003) :: High Frequency Squeal When RPM Passed 2300 - 2500
Anytime I run the RPM passed 2300-2500 I get this high frequency squeal. I don't seam to lose any performance, but very annoying. Is this the turbo having troubles. It's directly related to the RPM'S. Other that that, the truck runs great....
View 14 RepliesFord 6.0L Power Stroke Diesel :: Fan RPMs At Idle?
What's everyone's fan rpms at idle? Mine vary and lately I've experience a strange issue where fan immediately locks up and rages right after cold startup. Today it was running 2900 rpm. It settled to about 480-500 but I know I'm the past it's been like 300 or so at idle.
View 6 RepliesFord 6.0L Power Stroke Diesel :: 2003 - Turbo Whistling Very Loud At Idle / High RPMs?
So I just purchased my first diesel a couple weeks ago (2003 f250 Lariat). I love it! However, I'm having concerns about my turbo whistle on it. At idle and while in higher RPMs is sounds ridiculously loud (even at 0 PSI in the boost). I've been doing my research on it and I know the 03's have the loudest sounding turbos because they have less vanes than the later models. I know without a video it's going to be hard to diagnose, but I am wondering if a loose boot would cause a turbo whining sound through the exhaust? I have yet to hear ANY other diesel in person that has a turbo whine as loud as mine.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Six CEL Codes / Stall Out At Times / Shutters Or Pops Between 1800 - 2500 RPMs
I have a 1999 Ford F-350. I have six codes from my truck. The codes are P0237 P1119 P1690 P0500 P0603 P0344. My truck runs, but likes to stall out on me for no reasons at times. The other problem I am having is between 1,800-2,500 rpms, she shutters or pops.
View 7 RepliesFord 6.0L Power Stroke Diesel :: 2006 E350 Truck Started To Stall As RPMs Dropped
New here but long time lurker. I have a 2006 e350 with 6.0, bought it from a friend not long ago. The work that has been done to it the last 50,000 miles is as follows.. New hpop, all new injectors, egr delete, sct tuner, stand pipes and dummy plugs. I had it for a week and would get a no start hot once in a while. This issue had become worse and the truck started to stall as the RPMs dropped. Reading here i replaced crank sensor and the stalling stopped but the no start hot continued. I took it to a local diesel repair shop and they did the following..
Use a test ipr (no change), replaced ipr pigtail (was cracked) air test (leak under pass valve cover) replaced stand pipes and dummy plugs on this side. They said no leaks and I was good. Truck worked as its supposed to for 1 day and the no start hot issue reared its head again. Took it back and now they say the hpop is bad. The pump that was put in about 50,000 miles ago was a bostech? do these go out? Sangauge reads good ficm, but seams ipr doesn't climb that quick.
Ford - Escort :: 1998 - Cannot Get Idle On The Car To Go Below 2500 RPMs
I have a 1998 Ford Escort which I drove about 450 miles in frigid weather over about 8 hours in mid January. After arriving at my neighborhood and getting off the expressway, I couldn't get the idle on the car (manual transmission) to go below 2500rpm's. Further, upon taking off, the car was trying to stall, and I was forced to feather the clutch through town driving and keep the throttle up so it wouldn't stall, even with the clutch in. The weather at the time was about -7 degrees (f). The next day the weather continued, and thee car would start, jump to the same idle for 10 seconds, then drop suddenly to 500rpm, then stall out. I wrote the car off, cleaned it out over the next week, and then I tried to run the radio while doing so last weekend. I got the car to start, and run normally. I think it may be a computer issue, but it may also be the temperatures. The car has 207,000 miles on it.
View 3 RepliesFord 6.7L Power Stroke Diesel :: Batteries Died Again With 2500 Miles?
I didn't drive my truck for one day and the batteries are died. This is the second time this has happen. That is a pretty fast drain time. THe truck only has 2500 miles on it. And I;m talking the batteries a dead dead. I hate having to take the truck to the shop. Just a big inconvenience. And it only happens about three weeks apart. I bet that would be pretty had to find the problem.
View 5 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Started Surging At Idle
Just bought a 2006 F250 with 6.0. A week or so ago, it surged once at idle at a light. Sort of felt like someone bumped into your rear. It has gotten more frequent over the last week or so. Now it does it often. It tends to rev up and then back down again over and over. Then it will clear up again. My brother said his 7.3 used to have a similar problem (as did quite a few others apprently) and it was the Cam positioning sensor (CPS). Where is it located?
View 14 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 Running Rough At Idle
I have a 2006 f250 with a 6.0 with sct livewire, arp studs&gaskets, oil cooler, blue spring mod, sinister egr cooler and it had been giving me some real troubles lately. Started off as a code for injector #8 so I replaced that and while I was in there I rebuilt the oil rail with new nipple cups and orings, replaced standpipe and dummy plug in that bay(also updated the arc fitting less than a year ago), new exhaust back pressure sensor tube because it was right plugged with carbon, and a new egr valve because that was right packed with carbon as well, all backed together and torqued to spec from the Haynes manual and the truck still sounds like its missing at an idle with some light smoke(just smells like unburnt fuel). From there I went to test the ficm which is also only a couple years old and it seems to stay at a constant 48v so at this point...
View 11 RepliesFord 6.0L Power Stroke Diesel :: 2006 - Hesitates Intermittently - Stumble At Idle?
I have a 2006 F-250 4x4 with no cat, and no egr but the valve is still connected. It has about 146,000 miles. Just recently when warm, it has a slight miss every once and a while when stopped and in gear. Just a slight drop in RPM then recovery. Its mainly used on the highway and 99% of the time I set the cruise and its smooth as silk. Every once and a while I feel it stumble once or twice, recover and it is fine for the next 80 miles with no issue. It started as once every few trips but now It seems to be happening at least once every other. I use Motorcraft filters (maybe 6K on the fuel filters) and rotella oil. My scangaugeII shows no codes and no Injector pressure issue (1200-1400 at 75 mph depending on grade) and the FICM voltage stays between 48.5v and 49.0V. What should I check?
View 2 RepliesFord 6.0L Power Stroke Diesel :: 2006 F250 - Engine Revs Up At Idle
I have a 2006 f-250 6.0. About 2-ish months ago, it started revving up while I was parked and hooking up a trailer. It ended up needing an ICP sensor and pigtail wires. Was fine after that until around 10 days ago, it died when I was driving down the road and wouldn't start back up. That time it was the IPR. Got it back Friday, drove home (40 min) and didn't need to drive it until today. I fired it up, and we're back to the revving/surging. I decided not to take it on the road, really tired of being stranded. Could it be the icp again? Something else? I'm so tied of throwing money at this thing.
View 7 RepliesFord - F150 :: 1989 - Idle Dies When Put In Neutral Or Gets Stuck At 2500 RPMs
I got an old 1989 F-150, manual, in-line 6 engine, with an 8-foot bed. I use it for hauling landscaping equipment, as i am starting a business. i will likely start hauling trailers with it this summer, but I also just want the engine to give me more power.
What are some things I could do to up the HP, or a better truck in general. I'm not looking to make it into a 350Hp monster, just get a little more out of it. What can I replace or add that would do this?
First, the idle dies on me when i put it in neutral, or gets stuck at 2500rpms. is this a vacuum leak, or the idle-air control valve?
Ford Ranger / B-Series :: Hissing Noises And Idle Fluctuate Between 2500 And 3000 RPMs
Truck: Ranger
Year: 1990
Engine: 2.3 Lima
Trans: 5 Speed Manual
Miles: 83,445
Recently Replaced:Oil Pressure Switch
Oil Pan Gasket
Crank Position Sensor
Spark Plugs
Plug Wireset
Ignition Control Module
Driver Side Coilpack
After I got done with all of this crap on my Ranger, I noticed that it was driving great! But...today I was on my way to school and BAM! My engine idle started hitting (presumably because I do not have a tachometer) about 3000RPM and lowering down to about 2500RPM and from there, every time I am not in gear it decided to fluctuate between 2500RPM and 3000RPM. Crazy style too.
Now, I got to school, and getting closer to it at a stop light the truck basically died. It was almost at 100'ish RPM. I gave it gas, and BAM. I hear a continuous hissing noise from under my hood. Haven't diagnosed it fully yet because I just got home and its 12AM.
Now, every time I stop at a light or in traffic or whatever it may be, I have to give it gas every other second, like a small push on the pedal, to make sure the truck doesn't die. Also, every time I am out of gear and my RPM's are at an 'idle' state, I get continuous hissing from somewhere, I get no power loss or anything, just really weird idle RPM's and hissing when my foot is not on the gas basically. It is strange. I think It is some sort of Vacuum leak but I am not sure.
To get a better picture of the 'hissing' noise, it is the same hissing as you would hear when letting the air out of a tire. That is the best way I could describe it.
Ford 6.0L Power Stroke Diesel :: 2006 - Rough Idle / Dies Warm And Long Crank
My 06 currently has 296k miles. 3 years ago I put a lot into her. Dummy plugs, stand pipes, STC, hg,studs, oil cooler, bpd egr cooler. Cleaned spool valves and fresh o rings in injectors. (Alliant) plus a lot more that I can't remember. Ran very very well after all that.
Fast forward to a few weeks ago. Driving down road and truck died as I let off pedal to slow down for turn onto my road. Took about 7-8 tries to get started back up. Icp was reading in the 300's until it finally started. Made it home. Shut it off. And started right back up.
Few days later truck died again same way. Let off to make a turn. Several attempts to restart icp was in the 300's again. Once it started building 420ish it sounded like it was firing a few injectors and slowly started running. The next time it happened the same way but when I got it back running I eased to my inlaws like less than a mile. When I got to their house and pulled in and went to back up to turn around the display on dash said low oil pressure and started missing a little. So once I got home started researching.
A few days ago I pulled out the low pressure oil regulator to check it out. It was clean but did have some mild scaring. I used some fine scotch rite and smooth it out a a little. It moved freely in the bore so I put it back together. Then pulled the oil filter cap off to check the little black valve. I noticed the filter was not dripping with oil like normally when I change the oil. And yes it's motor craft filter and cap. It checked out ok. Press it down and turned engine over and it filled and held. Let off of it and it drained.
Next I air checked the high pressure side. Applied air and waited until I could hear the air (IPR still open) then closed the IPR. Couldn't hear any leaks. Just a very very minor his and couldn't pin point where. So I went ahead and went to dealer and got new stand pipes and plugs. And ordered new print set for injectors. Pulled injectors and didn't see any smoking guns. Replaced prongs, stand pipe and dummy plugs and put it all back together. Cleaned the injector cups and hold down bolt holes. Torqued injectors to spec.
Got it all done and rotate motor by wire next to heater blower to assist prime system. Tried to start it up and it took two tries but fired right up and sounded smooth as hell. After it idled a few minutes I saw a haze from exhaust. It smelt just like fuel. A few minutes later started idle a little rough. Gave it some go pedel and it was rougher at about 1600-1800rpms and couldn't feel it above 2k. Got my laptop out with AE and done balance test. Did not show anything. No codes either.
Ford 6.0L Power Stroke Diesel :: 2006 F250 - Rough Start And Idle When Engine Cold
Truck has been doing this and now getting worse. 06 f250 6.0 147,000 miles. Runs like crap when you first start and truck has trouble shifting when I first take off in the mornings until it warms up then it idles fine and runs like a champ no problem shifting. Not in a cold climate 40F at the least. Not trying to take it to the dealer and get raped. Been doing research some people say get the inductive heat flash, some say needs new injectors, some say could have a bad gasket on the injector idk. I'm trying trying to get it resolved....
View 4 RepliesPrius (2010-12) :: High Engine Idle Speed - 2500 RPMs
Had a first-time issue with my car today. Background, 2010 II bought in June, just short of 15K miles, never had any kind of mechanical issue.
While en route to work this morning, I was about halfway into my 15 minute drive to work, when I noticed my engine was idling very high, I would guess 2500 rpms. It started doing it while I was driving around 35 MPH, then continued doing it while I stopped at a traffic light, and continued when I continued driving to a speed around 50 MPH. The high idle while stopped was not transferred to the wheels, so it was not a safety issue as it would be in other cars.
When I got back up to 50, curious to try something, I hit the ECO mode button and the car returned to normal. I took ECO back off and the car was still fine. I had no further problems.
I would point out that this morning was about the coldest temp that the car has experienced. Outside temp ranged from 7 to 10 degrees.
Honda - Accord :: Idle Is Fine Until Engine Warms Up, Then Fluctuates Between 1500 To 2500 RPMs
!995 honda accord, 5 speed. Idle is fine until the engine warms up, then fluctuates between 1500 to 2500 rpms. The idle control valve was cleaned- no change. Valve was also replaced -also with no change. Put old valve back on. Computer was disconnected after cleaning and also after each valve change.Would the next step be to remove and clean the fast idle thermo sensor? Also how do you check the coolant lines coming in. Anything else I would need to check, clean or replace.
View 2 RepliesFord 6.0L Power Stroke Diesel :: Lack Of Power When Going Up A Hill On The Interstate At 2800 RPMs
While I'm cursing at highway speed everything is fine. But when u punch it it pass someone it's like I actually slow down, same from a red light. I've got a livewire programmer in it and this problem is somewhat new. It just seems to keep getting worse, I was going up a hill on the interstate this morning and at 2800 rpms I was actually slowing down. I'm not sure if the fuel pump is going out or if the transmission is slipping or what.
View 7 RepliesFord Transmission :: 4R100 - 2000 Ford Excursion - Grinding / Vibration Occurs Between 2100 - 2300 RPMs
I have recently found what sounds like a grinding/vibration issue that occurs between ~2100-~2300 RPM's in my truck. After some googling, I thought it may be the inspection plate being a bit bent/loose. I took the cover off and drove around and the noise still occurred.
Things I have noticed:
-Occurs between 1-2 and 2-3 (had trouble with the other gear changeovers as I just have slow backroads around me to test over my lunch break- can test further in the future)
-Occurs during acceleration and deceleration
-Starts at ~2100 and ends ~2300 RPM
Any thoughts for next steps to diagnose? Truck has ~160k on it and I don't really have many service records (purchased within the past 3k miles and problem just started occurring after this past weekend). Transmission fluid seems to be in decent condition.
Not sure if it would affect anything, but I just got back from my first trip with the Excursion where I actually needed to utilize the 4WD. There was much more aggressive terrain than what it is used to seeing on the pavement. Thought I should mention that as well.
V10, if that matters (I recall reading somewhere that '99 7.3s with the auto had documented torque converter issues that warranted a TSB)....