Camry :: Turn Signals / Hazards Stopped Working
I used the volt meter wrong while testing my turn signal bulbs for power and not they do not work (or hazard lights).
View 3 RepliesFord Wiring/Electrical :: 2004 F250 - Turn Signals And Hazards Stopped Working
So I have an 04 F250 Super Duty 6.0L and suddenly the turn signals and hazards stopped working. First I replaced the switch on the steering column...no luck. Today I replaced the flasher relay under the dash panel (the blue one)...still no luck. I remember checking fuses in the fuse box but don't remember which ones I checked but I didn't see anything obvious. I also took a quick look under the dash at all the wires for any anomalies...nothing. I'm lost... What to do next!?
View 1 RepliesFord Ranger / B-Series :: 1998 - Flashers And Turn Signals Stopped Working
I recently got a pretty cherry 98 Ranger 3.0 2wd extended cab auto. So far all it has needed was wiper blades, floor mats and a heater blend door. Last week my daughter informed me that the flashers and the turn signals stopped working. I looked for blown fuses and then took the low road and just bought a new flasher (my alldatadiy manual showed that the flasher was common to the turn signals and the hazard flashers so I took a shot at just throwing a part at it). That didn't fix it or else. Any pointers?
View 3 RepliesFord Excursion :: Hazards / Turn Signals / Brake Lights And Cruise Not Working
Well, on our way home during my leave, the wife made the comment about halfway home that the blinkers had quit working. I assumed it was probably a fuse or relay, so we came on home. I have been looking at it for a few days now (too hot to spend too much time out crawling around under the dash ) and I am still having some trouble. My brake lights, and hazards are not working, and neither is the cruise, which was working fine while I drove before the blinkers went out.
I have no power at all to the flasher relay. I replaced the brake light switch because it was definitely worn and looked a little burned inside when I pulled it out and inspected, but still nothing. Have not found any fuses blown. Brake pressure switch fused link harness seems good with my test light. Wipers, brights, everything else on the turn signal switch works fine. Can't even get the cruise to go into diagnostic mode, it only blinks once when I try.
Taurus :: 97 Turn Signals And Hazards Not Working
In my 97 Ford Taurus the turn signals and hazards are not working. I changed the fuses, but still no luck. Someone mentioned that there might be another fuse box under the hood (besides the maxi fuse box). Also someone mentioned the blinker fluid being low.
View 14 RepliesLexus GX 2004-09 :: No AC / Turn Signals / Fan / Heated Seats - Hazards Still Working?
I've driven home from a tree nursery with a utility trailer - hazards on at about 60kph. Took me about twenty minutes to get home. It's a pretty warm day so AC was on. I turned the hazards off to signal turns and then put it back on when it was straight road.
After disconnecting the trailer and later driving to pick up the kids, I noticed the turn signals wouldn't blink but the hazards would still work. The AC would not respond, nor would any of the climate control buttons. The heated seat controls are dead and also the 12V DC outlet next to the seat switches seems to be dead. However, the airbag compressor control still functions normally, the diff lock button still works fine, the headlights and hi-beams still work as well.
I took a few minutes when I reached the first school to check through the fuse box under the hood but there wasn't anything obvious. I'm also considering just removing the negative on the battery to reset the computer. Then, there' s the window thing....
Ford Super Duty (1999-2016) :: EBrake Light Show Up On Dash / Turn Signals Stopped Working / Heated Seats No Longer Turn On
Coming back from a trip I got a e-brake light show up on the dash then noticed the signals stopped working and the heated seats no longer turn on. I scanned it with my AE and got a brake fluid sensor error come up but nothing about the signals .... is this a common problem or is there a connection between all this? 2003 F350 6.0L .....
View 2 RepliesFord Ranger / B-Series :: 1998 - Right Side Turn Signals And Flashers Not Working
98 4wd extended cab. So weird only the right side is not working. Lights in the dash to the lights outside everything is dead.
Fuses that I could find are good. We replaced the mf switch a few months ago.
Ford Ranger / B-Series :: 1998 - High Beams And Turn Signals Not Working
The turn signals and high beams do not work on my 1998 ford ranger xlt 4x4. I have replaced the multi function switch, the yellow flasher relay checked all fusses and all are good. What could be the problem?
View 7 RepliesFord - Contour :: 1998 SE Will Turn Over But Won't Start
I have a 1998 Ford Contour se 2.0. The alternator went out in the beginning of January. Had it replaced, got it back it ran for a couple of days and it just died on me and wouldn't start. So back to the shop it went, fuel filter was clogged so they changed it, and I got it back last Friday. It ran until Saturday morning and as I was driving down the road it just died!! Just like that...died. Got it to run for a few seconds...it would die.
Finally got it back home and now it won't start. It will turn over, but won't start. If it does start it won't stay running longer than 2 or 3 seconds. I've had the fuel pump, fuel injectors, and spark plugs checked. Everything is fine. Oh and yes, it has 3/4 of a tank of gas in it. What is wrong with this thing?? It also has around 151,000 miles on it.
Ford Excursion :: No Turn Signals / Hazards Work But When Press Brake Tail Lights Just Blink
I have checked all fuses, checked wires on top of steering column all checked out ok. Hazards work but when I press brake tail lights just blink with no brake light but the 3rd brake light works??? Signal switch maybe??
View 14 RepliesFord Wiring/Electrical :: 1973 F250 - No Turn Signals / Brake Lights Or Rear Hazards
Dad borrowed truck and wired 7 pin trailer harness. Lights worked on truck/trailer for use but upon return the turn signals didnt work. Hazards and running and brake lights did work. Replaced TS flasher and Haz flasher. Still no signals. Pulled steering wheel and replaced turn signal cam only, not whole switch. Now no brake lights, no rear hazards or turn signals. Losing my marbles trying to follow schematic and using test light and mulit meter. All bulbs and fuses are good. Running lights and head lights working as well.
View 6 RepliesPrius (2004-09) :: Turn Signals And Hazards Don't Blink
2004 Prius here. The turn signals and hazard lights stopped working a few days ago. I found a disconnection in the grounding and repaired it. Also replaced the fuse and the flasher switch. Now the lights work, and I can hear the flasher switch clicking, but they don't blink!
View 13 RepliesElantra HD (2006-10) :: Turn Signals Work But Hazards Do Not
Today, I replaced the flexible coupling in my steering column. All went well and seemed great until I realized my turn signals were not working. I tried the hazards and promptly heard the 10amp fuse blow. I took the paneling back off and realized that the wire bundle to the turn signal was being pinched above the steering column.
After lowering the front of the column down and removing the wires, I noticed that there was some damage. One wire (blue) was cut and a few others had damage to the sleeves. I repaired the sleeves and fixed the broken wire. The turn signals now work perfectly fine, but when I activate the hazards all the signals go dark. I cannot find any blown fuses and the relay appears to be working just fine for the turn signals.
Ford Ranger / B-Series :: 1994 - Turn Signals Stopped Working - No Flashing / Blinking
I noticed that my turn signals stopped working. I replaced the flasher. Now the turn signals work but the signal indicators in the dash don't light up. Also, the hazard lights don't work either. No flashing, no blinking when I turn on my hazards. I've seen many variations while searching? 1994 B3000 2x4 extra cab.....
View 14 RepliesPassat (B5) :: Turn Signals Stopped Working
So I get to explore my first repair with this new to me car. Yesterday morning, turn signals works fine. That afternoon, the stalk apparently stopped working, which I have heard of. Interestingly though:
-the brights and cruise work
-the hazards work (my improvised indication that I'm turning )
-the stalk had been replaced once before by the PO.
Did this thing eat another stalk, or are there some other things I should check first?
Ford Super Duty (1999-2016) :: 2000 F250 V10 - Hazards Not Turning Off / Turn Signals Don't Work
2000 V10 F250 - daughter is using my truck and called to tell me the turn signals weren't working. She called me shortly after and said she adjusted the tilt and hazard lights came on and now she can't turn them off. I had her pull the hazard fuse to stop them. She then noticed the brake light weren't working. I don't know if the brake lights were because she pulled the fuse or she just noticed they weren't working.
A week or two ago, she said she parked the truck, turned it off and took the keys. When she came back out, the truck had rolled across the street. Periodically, over the years, I would go to start the truck and nothing happened. I would shift the gear selector in and out of drive. Then the truck started.
Finally, since I've owned the truck, the when I activated the left turn signal, the selector frequently wouldn't stay "locked" till I turned. So, are these related? Do I have multiple issues going on in the steering column. Where to start looking when she gets the truck home?
Ford Super Duty (1999-2016) :: 2005 F350 - No Brake Lights / Turn Signals Or Hazards?
2005 F350 Super Duty. I have no brake lights turn signals or hazards. dealer suggested the multiswitch but changed it and still not working?
View 2 RepliesSonata NF (2006-10) :: 2008 - Turn Signals / Hazards Won't Work
I recently bought an 08 Sonata from a used car dealer which has 65,xxx miles. Last week my turn signals would work intermittently, and now neither the turn signals or the hazards work. I put in a new relay and a new turn signal switch, to no avail. When I turn the hazards on, the relay clicks once then nothing. When I do the turn signals, nothing clicks. Is there another relay I'm missing somewhere?
View 14 Replies