Civic - Honda :: Temp Sensor Broke Off And Can't Get It Out
My friend was replacing the temp sensor on his 2000 Civic, and twisted too hard and it broke off leaving part of the screw still in the hole. I got him a screw extractor kit, and he tried it this morning, and it too broke off. How to get these things out? I'm including a photo.
View 14 RepliesCivic - Honda :: Broke Down - Replace Transmission?
Took my 2003 Honda civic hybrid to a budget tune and lube. They said that I needed my fluid changed, I agreed, they changed it (did not flush it). It has 95k on it. Later that night the car broke down, I took it to honda they're telling me that I need a new transmission, there are pieces of a chain in the fluid that they drained. Supposedly the budget tune and lube used a CVT fluid called "Full throttle" honda is telling me that you cannot use anything but honda fluid and the tune and lube is not taking responsibility. Could this have destroyed the transmission?
View 18 RepliesSonata NF (2006-10) :: How To Replace Serpentine Belt Tensioner On 3.3 V6
How to replace the belt tensioner. It's not putting out enough tension when the engine is cold. So, the belt makes chirping noise for couple of minutes idling when cold with AC on.
I had the AC inspected and everything checks out according to my mechanic.
He believes that the issue is with the tensioner since I had recently had replaced the serpentine belt.
Tiguan :: New Serpentine Belt Tensioner After 1000 Miles?
I had my timing chain tensioner replaced. When they do this do they touch the serpentine belt tensioner? 1000 miles after the timing replaced, my serpentine belt shredded and they say I need a new serpentine belt tensioner. Does this sound correct?
View 3 RepliesGTI 337/20th Anniversary :: Tensioner Pulley Broke
My tensioner pulley broke yesterday and I replaced it. But it had broken 3-4 months ago also.
View 2 RepliesCamry :: Engine Noise - Bad Serpentine Belt Tensioner Is Seized On
After finally identifying a bad serpentine belt tensioner for being the the culprit for my engine noises, my mechanic said that the 'thru-bolt' is siezed. Since the replacement job was at my budget limit he said he doesnt want to get into it in fear that he has to brake the bolt and drill it out (requiring 2-3x more labor cost according to him).
If this is the case, and the 'thru-bolt' is seized, is this in any way something I can make a an effort to tackle? I have a jack and jack stands, and plenty of time.
Golf/GTI VI :: Chirp / Squeak Under Hood - Bad Serpentine Belt Tensioner?
So my mk6 developed what initially sounded initially like a bad serpentine belt tensioner. Only under anything more than load, and sounded like a bird chattering under the hood. Got outside today, fired car up, watched tensioner and it sat there steady as a rail. The noise is coming from the opposite side of the engine. Not really mechanical/metallic at all and tracks under load with the RPMs. Why i initially thought what i did. Not I'm sort of baffled.
View 3 RepliesChevrolet - Suburban :: Vibration After New Serpentine Belt Tensioner Installed
I installed a new serpentine belt tensioner into my 1994 Chevy Suburban C1500. It vibrated as much as the old one did, so I assumed that a bit of vibration is normal and forgot about it. Well, after recently looking at some instructional videos, I am now under the impression that any vibration in the tensioner is bad. Here is what is going on -- [UrL] .... Is it OK or should I get another new tensioner?
View 4 RepliesCamry :: Idler Pulley Replacement On Serpentine Belt Tensioner
2002 Camry 4 cyl. Can the idler pulley alone be replaced on the serpentine belt tensioner? I noticed a very slight side to side play when I had the belt off. No noise from it. When I looked at rock auto, they sell the whole bracket with the pulley.
View 2 RepliesLeSabre :: How To Loosen Bolt Of Tensioner Pulley
Which way do you turn to loosen the bolt that holds the tensioner pulley to the tensioner arm?
View 1 RepliesLexus RX 2004-09 :: 07 - Serpentine Belt Tensioner Pulley Making Noise
My tensioner pulley is making noise.I replaced the rear idler pulley (can't get to the front one), but still have the noise. Mention a DIY for replacing the tensioner pulley bearing. A part number for the bearing?
View 2 RepliesGolf V R32 :: Ball Bearing On Tensioner Seized And Broke The Belt
My ball bearing on the tensioner seized and broke the belt. Does that happen all the time?? My car is a CP and right now it's only 36k miles..
View 24 RepliesFord Aerostar :: 1997 - Squeaking Noise When Turning - Serpentine Belt Tensioner?
I have a problem with my 1997 aerostar. There is a squeaking noise that gets more significant when I turn. I am pretty sure this is the drive belt as the power steering fluid is fine. Should I attempt to replace the belt tensioner and if so is it just the pulley that needs replacing or the whole tensioner. I am by no means a mechanic but can figure most things out.
View 5 RepliesGolf V R32 :: Ball Joint Bolt Broke Off
I was putting on the H& R sports springs tonight and was onto the last corner, front passenger when one of the 3 ball joint bolts broke off. It was so rusted that the nut didn't want to come loose. I used too much force and out came the piece. Do I just go buy a new ball joint at the local VW dealer and swap it out. I didn't touch the other two and the car is still driveable. It's the middle one, exactly as shown in this photo from the DIY.
View 6 RepliesFord - Focus :: Broke Serpentine Belt Could Cause Loss Of Power Steering?
My 2007 Ford Focus broke down today. From what I can see and find online with my limited knowledge, it looks like the serpentine belt broke. Would this cause loss of power steering, rise in oil temperature and my check battery light to come on?
View 11 RepliesFord Escape / Hybrid :: 2006 - Serpentine Belt Broke When Going Down The Road
I have a 2006 Escape with a 4cyl. 2.3L automatic gas engine. Recently when going down the road my serpentine belt broke. I purchased a new one and attempted to install it. However, after routing it over all the pulleys there is still a significant amount of slack. Keep in mind when putting the new one on I didn't even have to move the tension pulley. Upon starting the vehicle I was able to see that all of the pulleys were moving and doing what was expected.
However, there is a great deal of squealing and risk that the belt with be thrown off or broken. I researched and am fairly certain that it is in fact the correct size belt as all the sites indicate the same part number and size. Could this be the result of a bad tension pulley that needs to be replaced? Need access to the routing diagram in case I may have put it on incorrectly? Am I missing some other form of adjusting the tension in the belt?
Ford Excursion :: V10 - Coil Bolt Broke Off And Stuck
Looks like if it was broken off but they tried to jb weld it in place and now I cannot get it out.
View 13 RepliesFord Brakes/Suspension :: Dreaded Wobble Over Bump - Serpentine Belt Broke?
OK, a couple of days ago I hit a good size bump and got the dreaded death wobble. I stopped to check the lug nuts and none were loose... jacked up one side at a time, tried shaking the tires to see if anything was loose and to my surprise on the drivers side I could move the tire back and forth (like turning the steering wheel, not around) so I figured something had broken right as I stopped. Is it supposed to do that?? I know it`s not on older vehicles.
Anyway I figured I was stranded so I thought what the heck, I`m gonna see if it will turn with the steering wheel. Well when I did... with drivers side still off the ground it gets the death wobble, oh it was running when I did it. I jacked it back down and it stopped so then I tried turning the steering wheel to see if it would turn and both tires turned as they should. I was scared to try it but I drove on home about 4 miles slowly.
My brother has an older Saturn and his wife was driving it and from the way he described it, it got the death wobble. Someone told him it was the serpentine belt. He changed it and it didn't happen anymore. Does it sound possible that the belt could be my problem. BTW, the truck is a 99 ranger 4x4 with no lift or anything.
Malibu :: 2012 V6 - Engine Mount Bolt Broke Off In Frame
Recently took 2012 Malibu V6 to dealer for warranty water pump replacement. During the repair the bolt holding the "snubber" (engine mount shock damper). To the frame was cross threaded and snapped off in the frame. Dealer contacted GM engineers and was told to replace that section of frame.
They told me that they would have to drop tranny n engine to do it and would have my car for 3 to 4 more weeks. They have already had it for 3 weeks. Anyway it sounds serious and i am concerned for the integrity of my vehicle after having that extensive of tear down and reassembly.