Chrysler - Transmissions - Ptcruiser :: Code P0700 / Hard To Shift Past Second Gear
My 2005 PT Cruiser (not turbo) is giving me a very frustrating P0700 code and a weird problem. First thing in the cold, autumn, the car drives perfectly fine (through still with the engine code on). Once the day warms up a little, the transmission decides that shifting past second gear is for punks and won't do it, so 30 mph has the engine revving at 3K rpm.
My morning commute is 20 minutes, and in that time, I go up to 50 mph with no issues. Driving home, or any other time of day, becomes the issue. What in the world could possibly be going wrong? I've been trying to hit up the junkyard for a PCM to see if switching that out would work, but it's been too rainy and cold to get out there.
Hyundai - Transmissions - Santafe :: 2004 - Hard / Lurching Shift Into 3rd Gear
For the past 3 months, upon shifting from 2nd to 3rd gear, the car lurches forward in a hard shift. Sometimes, it is nothing more than a benign "clunk", and other times it is violent, as if hitting a wall. This does not happen every time it shifts and even under identical acceleration, the results vary from none to violent. The number of violent shifts vs. small jolts has increased over time, and all other transmission functions and shifts are fine/normal. After much time researching the inter-blogs, I have come to no consensus on what is causing this or how to fix it.
Some say it is the adaptive shifting program and it just needs updating and others say it's the tranny and a rebuilt tranny replacement is the only thing that eventually fixed this problem (though one posting on the Hyundai forum is of the same exact problem, but the solution is worrisome -- contact negative battery terminal to positive, let sit for 10 min, reconnect, then drive at 1/3 throttle, shifting through all gears a dozen times. Poster says this resets adaptive shifting program and worked for him).
Finally, today, I took it in for a diagnostic with a local transmission specialist, and they could only replicate the hard shift once, but when that happened, he said the car went into limp mode and read two codes: P1193 and P2127. The car has never gone into limp mode (P1193) nor shown an signs of suppressed RPMs associated with this mode. Also, he seemed to focus his attention on the low voltage to the pedal position sensor (P2127) as being the major issue that is causing the hard shift. I also called a past dealer that worked on a similar issue with the car when I bought it used 4 years ago and they recommended updating the adaptive shifting program as they did last time; though I don't recall if the shifting issue was the exact same problem I am having now. So, a few things:
Does this sound like a computer issue or a tranny issue? Could the pedal position sensor having low voltage cause a shifting problem like this? Any merit to the connecting the battery terminals idea? Should I be wary of the mechanic that did the diagnostic today?
Chevrolet - Transmissions - Montecarlo :: 2002 - Hard To Shift Between Gears
I own a 2002 Monte Carlo SS 3.8 6cyl. I believe it has a 4T65-E transmission.
On a regular basis if I drive 20 miles out of town, on my way back the transmission starts to shift hard (long shift?). From my research online, the 4T65-e is a faulty transmission to begin with. Is it worth replacing the Shift and Pressure solenoids? If I were to buy a new transmission where should I look? What are some model numbers?
Oil, trans fluid, filters are changed on regular basis.New catalytic converter. No Check Engine Light.
Bmw - Transmissions :: 1998 - Clunks When Shift Into The Next Gear
I have a 1998 bmw 528i (e39) with 200k on it. It runs and drives like a dream except for one little thing.... when shifting into the next gear at around 25mph, if I let off the gas just before it shifts it clunks as it shifts into the next gear. However, if I accelerate through the gear change it is smooth as can be and has no problems through the gears.
Secondly and I believe unrelated, I am also looking for the location of a transmission temperature sensor... I have heard they tend to fail and can cause issues with shifting until the car is up to running temp. I experienced an issues with it once not wanting to shift out of 1st gear until it warmed but that was before a filter and fluid change. Since that, I haven't any issues, but I want to be prepared just in case with one on hand ready to go in.
Transmissions :: Car Won't Shift To 3rd Gear Even If Drive For 15 Minutes At 60 MPH
This problem started at the beginning of this winter. So I started to idle for 2 mins and the car was shifting without an issue.
However, now it is completely stuck and wont shift to 3rd gear even if I drive for 15 mins at 60mph.
Mercury - Cougar - Transmissions :: 1999 - Hard To Shift / Engine Codes
i have a 1999 mercury cougar and for almost a year when I drive it on the highway then get off and go to drive again it gives me a hard shift and will continue doing so, but if i turn the car off then back on it doesn't do it, very weird, but i got the codes and not sure what my next step would be to fixing it p1744- TCC system perform p1519 - IMRC stuck closed again this only happened when i drive the car for about 10-15 min on the highway then get off...
View 4 RepliesVolkswagen - Transmissions :: 2001 Golf Would Not Shift Up Out Of 1st Gear
It is a 2001 1.8T Golf, automatic. 75000 miles on it, mostly highway. I returned from my recent road trip, halfway across the country, which involved a couple of snow storms but otherwise everything ran smoothly.The day after I got back, I was going to dinner and the car wouldn't shift up out of 1st gear... unless I gunned it to almost 40 mph. Next time I started it, the check engine light turned on. I have driven it 3 miles, twice, since then and the problem remains. What the problem might be, if I'll need to replace transmission or just some fluid, or get a new car?
View 1 RepliesJetta - Volkswagen - Transmissions :: 2002 - Won't Shift Past 3rd Gear?
I have the above referenced car with about 65k miles on it. Today I took it for a drive, switched it to tip-tronic manual and found that the car would not shift past 3rd gear. When I switched to automatic, the transmission stayed on tip-tronic (the display indicated I was on 3rd gear). I had to fully stop the car, place it on park and only then did the transmission switch to automatic.
View 1 RepliesBrakes - Honda - Odyssey - Transmissions :: Difficult To Shift From Park Into Any Other Gear
I recently had a spin out on the ice in my 2001 Honda Oddessy Minivan and had to have the back wheel and front rim replaced. I definitely hit the sidewalk at least once and ended up backward in traffic with the back of my van on the sidewalk. Just after getting the work done I noticed for the first time that my car was having trouble shifting out of park into any other gear when starting and when I had it running but put it in park. I have to either press the brake several times, all the way into the floor to get it to shift out of park or pump it once or twice quickly and when I hear a little click, shift it into gear. Is this a transmission problem? Could it have been caused by my spin out?
View 3 RepliesMalibu - Chevrolet - Transmissions :: 2007 Chevy Will Not Shift Into 2nd Gear When Start Driving
I have a 2007 Chevy Malibu with around 190000 miles on it. Recently, first thing in the morning then I start driving, that car will not shift into 2nd gear for a bit. The engine will rev up the 2000 RPM and stay there. After a while it will finally shift. The fact that the engine stays revved that high for that long makes me nervous.
View 9 RepliesHyundai - Accent - Transmissions :: 2003 - Struggling To Shift / In Gear Suddenly Accelerate?
Ozzy is a 2003 Hyundai Accent with an automatic transmission. Over the last 2 year he has been having a lot of problems with his transmission. The first thing that was done was to replace his transmission fluid. Unfortunately the chuckle head that replaced his transmission fluid put the wrong kind in and he had to have a whole new transmission installed. And now only about a year later Ozzy is having transmission problems yet again. What is happening is that it feels like the car is struggling to shift gears and then once in gear it will suddenly accelerate.
Also, the idle races even when your foot is not on the gas pedal and yes, the check engine light is on. So, I have a couple of questions. First how much longer can she keep driving it like this before the engine falls out somewhere on the 405? Secondly how much is it going to cost to repair Ozzy? Also her driving the car when it is behaving this way is really dangerous, right? Because it felt pretty scary today when I was sitting in the passenger's seat and we were doing 75 on the freeway and Ozzy was shaking and making all sorts a noise. And lastly, she needs a new mechanic right, there is no way she should keep going to these guys that put the wrong fluid in and then replaced her transmission, right?
Ford 6.0L Power Stroke Diesel :: Torque Shift Trans / 4 - 5 Gear Shift Under Hard Acceleration
I have been having an issue with my 4-5 gear shift under hard acceleration and know that a rebuild is due soon but I was wondering if any high performance kit available with all the clutches and friction discs needed to rebuild.
View 6 RepliesFord - Focus :: 2001 - Brake Pedal Feels Hard / Transmission Hard To Shift From 1st To 2nd Gear
Could my brake issue be related to my transmission problem? Neither are constant. Brake problem= sometimes the brake pedal feels hard, like there's no power brakes (I drove a car once. ..looong time ago. .. that had no power brakes or steering) but it will kick in after a short distance. Transmission prob= seemingly unrelated, is a problem shifting from 1st to 2nd gear. This has happened maybe a 1/2 dozen times, the first time and mostly when in heavy commute traffic and when going between 1st and 2nd gear because of the slow commute speed, but also at other times when not in lengthy slow commutes. When it doesn't shift, the odometer doesn't work (shows only dashes) and an engine light comes on (the sprocket/gear looking one). Usually the transmission will eventually shift and the light goes off.
I read that the brake problem might be a vacuum hose problem? Something about a booster? Is this dangerous? or is it like having a car w/ no power brakes? Going to have my transmission looked at this week. Read on another site about dropping valve seats on this year car. If there's a major transmission problem, I'm wondering if it's worth fixing? I changed, timing belt, water pump, front and rears brakes, tires. 143,000 miles.
Chrysler - Towncountry :: 2004 - Shift Indicator Lights Up Every Gear
We have a 04 Town and County with about 97,000 miles on it. If we are sitting still for a period of time, it will drop into limp mode. You actually hear a clunk, then the shift indicator lights up ever gear PRND, they all appear with a box around them as indicated. It happens more often if the AC is running. Actually at stop lights we turn the AC off. It happened in line at a drive in movie once. After it sits for a bit it is fine. No issues going down the road. But it seems to happen if there is not movement.
View 1 RepliesGolf IV / Jetta IV :: Very Hard To Get A Smooth Shift From Gear To Gear
Background facts:
Tranny swapped from my 4 speed auto to a 1.8t o2j 5spd
13lb. Light flywheel
Powerflex dogbone mounts
Peloquin LSD
The problem: Very hard to get a smooth shift from gear to gear. Trust me, I know how to drive, but I can always feel the car shifting into a different gear if you know what I'm saying. On my friend's bone stock Jetta, I just let the clutch out without gas in between shifts and you don't feel a thing.
On my car, you feel EVERYTHING. People have told me the light flywheel will make the ride more uncomfortable in many ways, especially since the RPMs drop much quicker in between shifts than stock.
Timing-belts - Belts - Chevrolet - Transmissions - Aveo :: 2004 - Won't Shift From 3rd Gear Into 4th
The timing belt broke on my aveo, destroying the engine. I replaced the engine with a used one. Now I get the car back on the road and the automatic transmission won't shift from 3rd gear into 4th. Is it possible this problem was caused when the new engine was installed, or the transmission was damaged when the timing belt broke?
View 4 RepliesChrysler - Cruiser :: 2007 - Won't Start Easily After Maintenance - Gear Shift Button At The Top Of Lever Sticks?
I have a 2007 Touring Edition PT Chrysler Cruiser which was just a few days ago repaired because of damage under the front of the car. Front bumper, ouside and inside grills, all housings and connecdtions in the front area were replaced, including air conditioning mechanisms. Received car on Monday, Friday evening, it wouldn't start. Just made a tet tet tet or clicky kind of noise, no turning over of engine, then there was no noise ... just wouldn't start. Got jump, still wouldn't start until the third cycle that peddle was pressed. Now I'm finding that the longer I let the car idle, the more likely it will be to start after more than two hours of non-use. Had all electrical circuitry checked ... battery's 100 percent, alternator is working fine, but it's still not starting.
Car's gear shift button at top of lever is also sticking when I put it in park to turn the car off. Have to pull the top button up to get the key out. This was happening before car was repaired underneath front. Talked to warranty person, and he felt that maybe the ignition starter switch (if that's what's wrong) and sticking gear shift may have something to do with each other. Since car is actually starting after being run, maybe it's not the starter switch. I'd hate to get it repaired if that's not what it is. Thinking about having a Chrysler dealership do a diagnostic test on it to pinpoint exactly what is going on.
What's happening? Why is my car cutting not starting in selective situations after not having been idled for a couple hours or more?
S-10 :: Transmission Hard Shift Into 2nd Gear?
I get a hard shift into second gear, it jerks into 2nd but not all the time. I only notice it after driving on the freeway for several miles. It has 60,000 original miles. Service Engine Soon light come on after the hard shifts with a transmission fault code. I reset the Engine light and let it set 20 or so minutes and it shifts like new.
1997 CHEVROLET TRUCK S10 2WD
6 Cylinders 262 X 4.3L SFI
Automatic
Golf VI R :: Really Hard To Shift Into 1st Gear
I just finished the DG install yesterday. I am having a real problem with the first gear: it is really hard to shift into it (I mean hard!) - and several times I went into 3rd believing it was in 1st, while driving. I know that the DG is notchy and a little stiffer (which I like) but this does not feel right. I have to really push hard (moving slightly toward reverse) to shift into 1st. My wife would never be able to find it or shift into it (not that I let her drive my R that much...).
Note that all the other gears (2,3,4,5,6 and reverse) shift beautifully without any effort with that nice click. But not 1st.
What is it? Adjustment? I did it twice. I made sure that both cables were "all the way in" before tightening the first two bolts (and I made sure that the cables were not moving - a common problem with this install) with the engine lock on and pin in.