Chrysler - Ptcruiser :: 2005 - Slight Surge In RPM As If Car Is Trying To Idle Itself Even Higher Off And On
I did a timing belt replacement on the car. Checked the marks carefully for alignment since it took me nearly 2 hours to get them right to begin with, started the engine and it ran fine. Now, after putting the car back together again, the car will crank, and as long as I give it gas, idle smoothly at RPM's over 1000. Once I get my foot off of the gas, it will die, and I mean at once, no sputter or anything. I have pulled the IAC valve and cleaned it, and it seemed to do a little better in that i can let my foot off the gas and it will idle around 1000 RPM and slightly below, but it will eventually do the same, and the idle is ruff. I have also noticed while maintaining the higher RPM, there appears to be a slight surge in the RPM as if the car is trying to idle itself even higher off an on.
View 9 RepliesChrysler - Ptcruiser :: 2006 - Idles Rough And Shakes Between 50 And 60 Mph
I have a 2006 PT Cruiser with approximately 94K miles on it. This year I started a 2-hr round trip commute every week day, so the car went from getting ~200 mi. a week on it to ~700 mi. a week. I bought it used ~4 years ago with 28K mi. on it.
2 months ago, the car started shaking between the speeds of 50 and 60 mph. Not sure how to best describe it - kind of a shake/jerk, like someone was jerking the car forward very quickly and repeatedly. It seemed to be strongest in the front of the car on the passenger side, although you could feel it throughout the car. I took it to a repair shop. They balanced the tires, but that only very mildly worked. Then they changed the front axles (said there was a lot of play in them). They replaced the brakes, rotors, and timing belt at as well, for unrelated reasons. With new front axles, the shake disappeared, but the car has been idling incredibly rough ever since I got it back. You can see the steering wheel vibrate and feel it in the seat when I start the car or am stopped with it running. This never used to happen.
Additionally, the shake has now returned, but from the driver's side of the front of the car now. Again, it's between 50 and 60 mph, although it's slowly creeping up into the 60-65 range also. It's stronger if I'm pushing the gas down more, like when going up a steep hill. If I'm going downhill at 50-60mph, I don't notice it or barely notice it. On flat ground it's noticeable, uphill it's becoming severe.
Chrysler - Ptcruiser :: 2009 - A/C Does Not Work At Idle
A/C works fine when moving. At idle, it doesn't work. Fan is not spinning. Is it definitely a bad fan or is it a possible fuse/switch/module? How difficult it would be for a novice to replace the fan?
View 2 RepliesChrysler - Ptcruiser :: 2005 - No Electrical Power
I drove the car to town this morning, and then to work without problems. I go to get in the car and the car has no electrical power what so ever. I am going to check the voltage and battery terminals, but is there a fuse that sends power to everything in the car, including lights, horn, etc? There is NO power at all.
View 5 RepliesChrysler - Ptcruiser :: 2005 - Carbon Buildup And Clogged
Our 2005 PT Cruiser has a 2.4 liter turbo. We had to replace the turbo at 78K miles due to “carbon buildup and clogged” so said the dealer. I can not get any local mechanic to tell me why this happened or if it is normal. My wife claims it is because I have been using the cheap, mid-grade gas. I tell her, no, it was because of the cheap oil I was using. I am now using synthetic oil. One mechanic said the turbo needs to be “blown out” occasionally, by either high speed driving or fast take offs. Bottom line: What would make the turbo carbon up so badly that it must be replaced? What can I do to have this not happen again around 156K? Must I always use premium gas?
View 19 RepliesChrysler - PTCruiser :: 2005 - Broken Bolt In The Crankshaft?
Ok, here it goes. I was changing the timing belt on a 2005 PT Cruiser. Everything went good until I tried re-installing the harmonic balancer. No one in town carried the tool to reinstall the thing, so I ordered a tool from Amazon. I was installing the balancer, had a box end wrench just holding the bolt that screwed into the crankshaft and an adjustable wrench turning the bearing nut to push the pulley back on. I got the pulley down where the balancer and crankshaft started turning, so I held the box end wrench steady as I snugged the bearing to make sure it had bottomed out when the bolt broke down in the crankshaft.
Now, this bolt had threads at the top to turn the bearing, a shaft, and then about half inch but no more than 3/4 inch of thread at the bottom to thread into the crank and a long shoulder in between. The bolt broke at the bottom where the threaded part started. And, to make things worse, it turns out the bolt is made of pewter and is about 3-4 inches in the crank. I tried to feel for threads with the crank bolt itself, and t appears to be where the crank threads start. There appears to be abut 1/2 - 3/4 of an inch of space on the other end of the broken bolt. I have considered drilling the center out progressively bigger until I could get something in there to back the bolt out, and I am not sure I could get a bolt extractor down in the hole and then turn the thing to back it out.
Chrysler - Ptcruiser :: Shake And Rumble If AC On During Idle And Not Cold Anymore
So, I've had my car for about 4 years now. It's a 2008 basic PT Cruiser. About two years ago it started to make this weird noise whenever the AC was on. My car would shake and rumble if the AC was on during idle and the AC wouldn't be cool anymore. Whenever I was driving, it was fine. We charged it and then it quit doing that. A little after that, it started making this weird noise when I turned it on-kind of sounding like something was being banged around under the hood of my car. It also started to make this loud kind of screeching noise, and some gas or steam would sometimes (not often) come out from under the hood.
Then I got in a wreck and they said they fixed it when they repaired the car. Now, 2 years later, it's starting to make that same noise. The rumbling has continued, but when I charge it, it goes away. I just charged my AC about 5 weeks ago, but now it's starting again and the noise just started again this morning. I was told that there was a disc (something like that?) that may have cut my belt, but they said that they fixed that when they repaired my car from the wreck. If that was fixed, then shouldn't it not be doing this?
Chrysler - Ptcruiser :: 2005 - Power Windows / Top Not Working - Cannot Start Again
Last weekend we had our first warm weather up here in the Finger Lakes. My girlfriend wanted to be able to put down the top on her 2005 PT Cruiser convertible, but for a few months now the power windows and power top have not been working. She was going to take it to the shop, but I said, it may just be a fuse. I looked up the owners manual online, then drove the car to an auto parts shop and replaced the circuit breaker in the fusebox under the steering column, because it controls the power windows. The two passenger side windows started working but not the others. So I bought a fuse tester and tested all the fuses in the dashboard fusebox. They were all fine.
I drove the car some more, and couldn't figure out why the other windows wouldn't work. At one point I stopped but forgot to turn the engine off. I pulled some of the fuses out and plugged them back in, one by one. When I pulled one of them out, the engine stopped. I thought "uh-oh," then turned the ignition key to off and replaced the fuse. When I started the car again the engine light was on. I drove home (about 12 miles). I looked up stuff about the engine light on line and learned that after three trips, if everything is okay, the engine light will go out. That is exactly what happened. So I thought everything was okay except that I hadn't solved the window problem.
Two or three days later, my girlfriend got in the car to go to work in the morning. The car started but the engine light was on, and as she backed up out of her driveway the engine stopped. It wouldn't start again. The starter would just make a ratchety sound. We both figured my experiment with the fuses must have done something. I took the car (by tow truck) to a mechanic, and he didn't see how the fuses could be the problem. It turned out that the starter was bad and had burned out the battery. So I paid to have the starter replaced and a new battery put in. But when we picked the car up, he said what I'd done had nothing to do with the problem. He said the starter had probably been bad for some time, and it was just a coincidence that the car broke down a couple of days after I fiddled with the fuses. Now I'm convinced he's right, and my girlfriend is just convinced that he's wrong.
Chrysler - PTCruiser :: 2005 - Getting Engine Error Code P0016?
I just wanted to post this due to the problem I was having with this code. I recently replaced a broken timing belt on my 2005 pt cruiser (non-turbo). Everything went back together, minus the hours trying to get the timing marks lined up by myself. After getting the engine buttoned up, the car would crank and idle, but only after 2000 rpm and the engine code P0016 would show up. I went back into the engine, reset the timing belt, and cranked it before putting everything back together. Worked fine, so buttoned it back up and took it for a test drive.
Bam, same engine code pops up again, only this time the car acted like it wanted to go into limp mode for half a second after driving for a few miles when I was turning around to come back to the house. It straightened up and drove fine. I could drive the car fine even after that, made a few test drives into town. The car would kind of fight limp mode after first cranking the car and accelerating, but then straighten up.
After a couple of months of research and talking to a friend who is a pretty good mechanic, I decided this was an electrical problem. I checked, and sure enough, after looking at the wiring at the cam shaft sensor connector, it was frayed. I spliced it and still had some issues with the code. I had just put a new sensor on it when the belt broke thinking it might be the sensor, so I put the old sensor back on it and now it runs fine, no more light. So, after months of thinking the timing or tone rings might be off, it was just a wiring/sensor issue.
Chrysler - Ptcruiser :: 2005 - Grinding Noise In Engine Compartment
I have a 2005 PT Cruiser non-turbo. A short time back, the tensioner bolt broke on the alternator and after spending several months going back and forth with the dealer, I was finally able to find the correct size bolt to replace it. Shortly afterwards, I began to hear a scraping sound coming from the engine compartment. The sound is sporadic, and only lasts for a short time. The sound only appears to happen when the engine is idling down when coming to a stop, and it doesn't always do it.
It doesn't make the noise when accelerating, in fact, the noise quits when I accelerate. The noise sounds like metal being drug on concrete, or a grinding sound. Is this a possible bearing going out on the alternator or possibly the AC clutch/bearing? The noise is not present during normal driving conditions, just when the car is almost at a stop and stops as acceleration occurs. I have reached in to see if possibly a loose pulley/bad bearing on the alternator, but there is no slack there. Is it possible that I have the alternator belt too tight, or is this another issue?
Chrysler - Ptcruiser :: 2006 - Shakes When Stopped At Idle In Gear And AC Compressor Is On
I have 2006 PT Cruiser Turbo Convertible that violently shakes when I am stopped at idle in gear and the A?C compressor is on. When I turn the A/C compressor off (leaving the fan on) there is a drastic reduction in the vibration. If I put it in park and turn the fan off, there is an additional lessening of the vibration.
I have taken it to three different mechanics and had the following done: spark plugs and spark plug wires changed, fuel injection system cleaned, the 'whatchamacallit' in the fuel system cleaned out, the two main motor mounts changed.
None of the above maintenance has lessened the vibration one bit. Question: What is causing it?
Chrysler - Ptcruiser :: 2005 - Bucks Under Acceleration - Map / Throttle Positioning And Oxygen Not Working
My 2005 PT Cruiser Limited 2.4 Turbo bucks under acceleration and had displayed the codes for a bad Map Sensor, Throttle Positioning Sensor, and Oxygen Sensor. I replaced both Oxygen Sensors, Map Sensor and the TPS. Each time I replaced a sensor and took it out for a test drive it ran great. The next day my wife is on her way to work and I am on the phone with her, she accelerates to get on the freeway and the bucking is back. The codes it displays now are P2074, P1697 & P0038. All the previous codes except P0038 disappeared when I disconnected the ground cable for 15 minutes after the repair. I start the car every morning for her and run the heater for 15 minutes as it is in the 30's here in the morning and so I replicate that before I take it on a test drive after completing a repair so the conditions are the same.
View 1 RepliesChrysler - Ptcruiser :: Shimmy At 70 MPH
My son's wife has a PT Cruiser, she told me last night that it has a shimmy at 70 mph. What are the causes of this ?
View 10 RepliesChrysler - Ptcruiser :: Wobbling While Going At 55-60 Mi/h
My PT has a vibration, I've replaced rear drums, rear hub assemblies, front brakes and front rotors and all four tires.The vibration is only while going 55 to 60 MPH each time I've replaced the different parts (rotated the tires and rear drums) the wobble seems to go away for about a few miles and then comes back!I'm going to replace the front hubs and bearings now, but why would the wobble change each time I changed I've changed all these parts around. Could it be a bent rim? or just the front bearings?
View 5 RepliesChrysler - Ptcruiser :: CEL Cause The Car To Buck Or Stall
I have a 2004 PT Cruiser with 111,000 miles on it. A summer or two ago, whenever it got hot out, the check engine light would start to come on. Usually, it didn't affect the car's driveability - but sometimes, it would cause the car to buck and/or stall, sometimes to the point of stalling completely out. Brought it into the shop again and again. Camshaft sensor. O2 sensor. Crankshaft sensor. Replaced. Checked. P0304 misfire code came up in diagnostics again and again. Re-wiring of camshaft sensor wires. And on and on. And yet again, intermittently, the check engine light would come back on and the whole thing would start all over again. Sometimes you'd drive it, stop somewhere, start it again, and the check engine light would be gone. Sometimes it would stay on for days. Weeks. Sometimes with no other driving symptoms - it just depends on how the car is feeling? I thought the problem was limited to the hot months of summer, but now it's the dead of January in Minnesota and it's happening again. Yesterday, it stalled out completely and I had to get it towed to the shop - decided to try a new shop, they said maybe the problem was that the old shop did a bad wiring job. OK. But then, got the car back, no check engine light on first drive, stopped somewhere for 5 minutes, get back in, start it again, check engine light back on. But at least the car started and didn't buck/stall. Now it's back in the shop, but I'm ready to give up.
View 5 RepliesChrysler - Ptcruiser :: 2001 - ABS Code 18?
What is ABS code 18 2001 PT Cruiser???
View 14 RepliesChrysler - Ptcruiser :: 2002 - Car Won't Start At All Just Clicking
I have a 2002 chrysler pt cruiser. For the past week when I start to crank it it will just click one or two times then crank. Today it won't start at all just clicking.
View 2 RepliesChrysler - Ptcruiser :: 2007 - Tries To Stall When Stopped
I have a 2007 PT Cruiser that's just about to hit the 100,000-mile mark. My problem is when stopped, the car feels like it wants to stall, but only when the AC/Heater/Defrost is on. Also, when it starts to act up, the heater stops working, leaving only the fan to blow air around. It doesn't happen all the time, but enough to make me turn off the heater or whatever I'm using when I come to a red light. It just started doing this and I just wanted to have a rough idea as to what it was before I took it to a mechanic.
View 6 RepliesChrysler - Ptcruiser :: Overheating And Temperature Light Comes On
After running for a while traveling to and from the store, my temperature gauge on my 2005 PT cruiser rises to hot and the temperature light comes on. However,when I get out and raise the hood. The engine doesn't seem to be overly hot. No boiling or hissing sound and no steam coming from the engine.
View 3 Replies