Chrysler - Cirrus :: 2000 V6 - No Start After Sitting Out In Wet Weather
2000 Chrysler Cirrus 2.5 V6, 84,300 miles. Twice, after sitting out a day or 2 in wet weather, it was very, very difficult to start. Each time, it didn't fire at all, but then did finally start after 4 or 5 tries and ran fine.
Tried spraying water everywhere under the hood, while it was running, but got no miss or other symptom. After then sitting a day or 2 in the garage, it started and ran fine the first 2-3 miles, then started stumbling/missing and stalled at a light. It restarted and continued to stumble/miss before running fine after another 1-3 miles. Changed the distributor cap and repeated the same test, getting same result. Also checked fuel pressure--it's on the money, building specified pressure and holding as expected. No check engine light or other symptom and no relevant codes.
Chrysler - Cirrus :: 2000 Lxi Died While Driving On The Highway
My car died while driving on the highway. The mechanic said it was the distributor, but also that the fuel pump wasn't working. When he replaced the distributor, the car works, no fuel pump problem. Does the fuel pump shut off when the engine dies or is this going to be another problem down the road? 2000 Chrysler Cirrus Lxi...
View 1 RepliesChrysler - Pacifica :: 2006 - CEL On / Code P0305 Cylinder 5 Misfiring
So my Pacifica, after a long road trip around a year and a half ago, had it's check engine light come on. The meter read P0305, which is cylinder 5 misfire. When I got home, my local trusted mechanic replaced the coil and wire. Since then, the same misfire has occurred at least 4 times, and 3 of which he replaced the same parts (free warranty swap of the parts). The last time, he was determined that it wasn't simply the parts going bad. I concur. It has now lasted roughly a month and the light is back on with the same code. The spans have been as little as a week between leaving the shop and the light coming back on. I personally don't feel the car riding rougher than normal, but my wife does. I don't smell gas, have odd colored exhaust, or any other issue. The only other thing, which idk if it's related, is a clicking noise from the engine, which quickens with revving, perhaps the risers. What else could it be? I read that Chrysler's go to is a valve spring retainer lock and a MAP sensor that accompanies it.
View 19 RepliesPassat (B5) :: 2000 1.8L - Fault Code / Vacuum Leak Diagnosis
I have a 2000 1.8L that's great. I have seen a reference to Vacuum leak diagnosis. I have a check engine light on and it has been for a while. the car still runs well and gets fine gas mileage. Coed is 1136. Is there a specific hose I should check?
View 7 RepliesPassat (B5) :: 2000 1.8T Vacuum Leak On Cold Start - Emissions Workshop 1 Code Flashing
I have a 2000 Passat 1.8T. When I start it up in the morning I hear a loud obnoxious noise like a vacuum leak from the engine compartment. It lasts for about 1.5 minutes then runs normally. After about a minute it starts up again and only last for about 7 seconds...ish. When I drive it afterwards, less that a half block or so, the CEL light goes on after 1 beep. Also, at that time I get a messages from the instrument panel that says "Emissions Workshop 1". I've read that it could be a simple damaged vacuum hose to the secondary air pump. Definitely a huge price difference to repair.
This morning is was colder outside than usual and the dash kept beeping and flashing the "Emissions Workshop 1" code intermittently.
Chrysler - Cirrus :: 1997 Won't Start On Its Own Without Being Jump Started
I have a '97 Chrysler Cirrus that won't start on it's own without being jump started. Once jump started it runs fine, but then the next time you go to start it the battery is drained again. My highly uneducated guess is that I need to replace the alternator. Am I on the right track? I replaced the battery and the problem persisted.
View 7 RepliesChrysler - Cirrus :: 1997 Will Randomly And Unpredictably Go Into Limp Mode
1997 6 cylinder Chrysler Cirrus 162,000 miles. My car will randomly and unpredictably go into limp mode. I suddenly find myself in second gear while my engine is revving at high speed (3000-5000 RPMs) in order to maintain velocity. The check engine light comes on immediately, but usually switches off after 2-3 days maximum, and typically less than that. If I pull over, and turn off the engine, it re-sets, allowing me to start the car, and continue my journey, shifting normally.
Additional pertinent information:
• it happens more often when the weather is warm
• it has happened while traveling down the highway at 65 mph (scary!)
• at times, the shift into second is so abrupt, it feels as though I have been rear-ended
• once, while in a traffic jam and moving at about 20 mph, I hit a pot hole and the engine started revving at 3000, with no change of gears
• a couple of times, rather than throwing me into second, it has seemed to throw me into neutral, with the familiar high revs, but absolutely no power with increased pressure on the gas pedal
• it is happening with increased frequency i.e. I have had to stop as many as six times during an 16 mile trip.
• Recurring computer codes: P0140, P0141, P0700, P0765, P1494
04/2011 replace right front cam sealFront engine mountReplace front valve cover gasket w/tube sealsFront bank spark plugs & wires (3 platinum plugs)Transmission flush
05/2011 cylinder #5 misfireReplace rear valve cover gasket & tube seals3 platinum plugs (leaky power steering pump fouled the plugs)
05/2011 recall work #C45 floor shifter ignition/park interlockPush rod trans- shifter
09/2012 transmission shift solenoid
10/2012 6 new plugs & wires Plenum gasketDistributor capEGR valve gasket
There has been other service work done during this time period, but (I think) I have included only that which may relate to the transmission. I am so frustrated, and my mechanic is stumped. He has referred me to either a transmission shop, or a Chrysler dealer. After hearing my account of the problems over the phone, the head mechanic at the dealership suggested that it’s time for me to get a new car.
Chrysler - Cirrus :: Speedometer Stopped Working - Sensor Or A Cable?
I have a 97 Chrysler Cirrus, and have been driving it for about 5 months. The other day, as I was driving, the speedometer stopped working. It did that one time before, but started back working. However, this time, it still is not working and I have no idea how fast/slow I am going. Often, my car has little glitches where you have to lock/unlock the door a certain way or it does not work right. Everybody jokes that my car has OCD! Also, once you crank the car, you have to turn the key back halfway or certain things don't work- like the clock, wipers, turn signals, etc. I don't know if this is related to the speedometer situation or not. The last time the speedometer stopped working, I had the AC on and a cassette tape in the deck; I was trying to hit the rewind button, but kind of accidentally pushed between fast-forward and rewind, and that is when the speedometer stopped working. I am not sure this is related. Do you know if my car has a sensor or a cable for the speedometer? Is this something that can be easily and inexpensively fixed?
View 1 RepliesChrysler - Cirrus :: ABS Light Came On / RPM Gauge Stopped Working Occasionally
I have a 1997 Cirrus. The ABS light came on about 2 weeks ago -- this is after i drive about 30 yards. The brakes seem to be operation ok and when the light does come on there is no bell or chime sounds to indicate something is wrong. ALSO, the RPM gauge just started to not work. Occasionally it may operate correctly but most of the time it just sits on zero. What the fault or faults are?
View 1 RepliesStalling - Chrysler :: 1999 Cirrus Would Randomly Stall When Driving Or While In Idle
I started having problems with my '99 Cirrus last month, it would randomly stall while driving or while in idle. With no check engine light or any other tell tale signs of a problem. I'm not entirely knowledgeable about how the entirety of the car's systems function, though I new I should check my fuel system. I wasn't getting any fuel to the engine whatsoever, so I replaced the fuel filter because when I got it off and looked at it it was clear it was bad. Then I put it all back together to try and run it and it continued to stall.
Thinking it must be the fuel pump at this point I dropped the fuel tank and replaced it. It ran for about 35 miles before the same problem started happening again. So I checked all the fuses, and relays and just to be safe replaced all the relays related to the fuel pump, and fuel system and i even replaced the auto shutdown relay. The car continued to have the same problem, so I did some research and found out it could be a dirty throttle body so I cleaned it even though it wasn't that dirty, and checked my air filter for how clean it was and it was clean. The car still continues to stall in idle and while driving.
Chrysler - Cirrus :: 1998 Not Starting / Mild Thud Followed By Brief Hissing Sound When Turn The Key
My 98 Cirrus (V6 automatic) is not starting. The battery is working fine and it lights up everything...the wipers, headlight, the turn signals etc.... But when I turn on the ignition...nothing. I hear a mild thud followed by a brief hissing sound when I turn the key from the 1 position to the 2 position (referring to a 0-1-2-ignition key positions)...like "thuh...sssssss." It seems it comes from the underside of the car. Then when I turn from the second key position to start the engine, I get no response at all. I tried putting the gear in park / N...but no difference.
The weird thing is, approx 15 min before I attempted to start the car, I had to drive the car across the parking lot. It ran fine at that time. Could it be a fried starter motor?
Accent LC (2000-05) :: CEL Blinking / Code P0303 - Knocking Sound From Engine
I have an 05 Accent with about 115,000 miles. It is a GLS automatic.
This morning as I was pulling from a stop light about 30 seconds from my office the car was extremely sluggish. I noticed the CEL light blinking and could hear a knocking sound from the engine. I pulled over and found code P0303, cylinder #3 misfire.
I checked the spark plug cable on the coil side it looks ok. I have not been able to check anything else yet as I am at work.
Golf IV / Jetta IV :: Fixing Code P1136 - Vacuum Leak?
As title states, I scanned my gti and got P0420 (nothing new here) and P1136. I did some searching and looks like vacuum leak can cause this, however I also read that it'll affect my idle. I replaced MAF 2 years ago with a brand new OEM one, my idle is NOT rough, at all.
View 1 RepliesFord - Explorer :: Got Code PO442 - Vacuum Hose Leak?
I popped a code this morning PO442 emission control evap [small leak]. Would this be a vacuum hose leak? I did both heads about a month ago. Any way to narrow down the troubleshooting on this problem?
View 6 RepliesFord F-150 - 1997-2003 :: Code P0171 And P0174 - Vacuum Leak
I had my fuel system cleaned by the dealership last weekend and I feel like I gained 50hp+ ... Now its throwing a P0171 about a week and a half later. My computer also listed P0174 under the pending codes or whatever the section was.
2003 F150 5.4L ... I cleaned the MAF sensor a couple weeks back which stopped a rough idle and I have put some 300+ miles on it since. about 200 miles since the fuel system cleaning.
I got home and popped the hood and it sounded like a vacuum cleaner. Guess it is a vacuum leak. I might need to stop using this ford house. I swear this is the second time there was a vacuum leak(I think, first time they said it was spark gap issue). I'll be heading back in the morning now.
Ford - Explorer :: Getting Code P1405 Large Vacuum Leak And Alternating Replace Gas Cap
Got 2006 Explorer back fron trans rebuild and probably unrelated but started getting P1405 (Large vacuum leak) and alternating "replace gas cap" errors. When I installed a new gas cap, error went from large vacuum leak -which I checked for on engine and found none using smoke test- to loose gas cap. So next, I changed the emission system valve which is right up front on rt. side of engine looking into engine bay. Now, error has returned to large vacuum leak. So new gas cap and valve. Error does not come back immediately after clearing. Takes about a week and then either get SES light and large vacuum leak error or just picture of gas cap on dash error. Note that when I remove gas cap, I no longer hear the "whooosh" of releasing a vacuum. Assume now it is in back by spare tire where I need to be looking. I note on emission valve that there is a schrader valve for testing vacuum....
View 6 RepliesFord F-150 - 1997-2003 :: Vacuum Leak On PCV Hosing - P1131 Error Code
I'm getting the p1131 error on my 2000 xlt f150 5.4l. I know it's usually a vacuum leak on the pcv hosing, which I did have at the back and replaced as well as other softer joining sections(3 to be exact lol), but I'm still getting this error. Changed out my plugs and cops(as they needed it) and the back two plugs on both bank 1 and 2(plugs 4&8) were both white! Since this is an obvious indication of a lean burning cylinder can I make the assumption my most likely problem is dirty fuel injectors on those cylinders?
View 13 RepliesFord Super Duty (1999-2016) :: Fault Code P0442 (EVAP) Be Caused By ESOF Vacuum Leak?
I have 2 issues and wonder if they are related. I don't have a CEL but I'm getting a P0442 DTC with my code reader - EVAP system leak detected
Also, my ESOF doesn't work. The hubs will lock manually. Can this be related?
I've already cleared the code and it came back. My ESOF hasn't been working for a while but I just haven't had the time or motivation to look into it until now.
I tried the HVAC Test and there may be a slow leak in the system. I can get the vents to switch from defrost to face vents but it switches halfway back to defrost, both are on at the same time for 20 seconds, then it recovers and goes back to the face vents.
My 4wd relays seem to work as well.
Chevrolet - Express :: 1996 - Code P0305 - Misfire In 5?
96 Chevy express 1500 V8-305. Have a P0305 code...Misfire on 5. Let me tell you everything I have done so nobody wastes their time.
I have, replaced the entire ignition system, "EVERYTHING" including a new distributor...Not the problem... I did a compression test...Not the problem...injector cleaning...not the problem.
When I moved the wire harness that goes into the "spyder" fuel injector system the engine smoothed out. I untaped the harness from around the plug and applied pressure to each wire the engine smoothed out. The back row 2nd pink wire seems to cause the most reaction.
My question is...Is it the wire harness or is it the injector system not reading plug? or could it be a combination of the 2? If I replace the wire harness might I still have to replace the injector system?