Silverado :: 2000 Chevy Truck Won't Start - Security Light On
I have a 2000 Chevy silverado. I recently was having problems with the transmittion not switching correctly. Long story short the shop told me to fix the problem I had to put in
A new transmition as well as a new computer which I did, from another Chevy. It worked for a few days then The truck was not starting and had security light on. Had alarm specialist take look and he said the computer had to be reprogrammed. It was reprogrammed at merles. And was still not working. Its unable to start, starts at random once in a long while. ignition switch was changed and still gave same problem. Took to another shop they had a specialist take a look and he said the computer had to be reprogrammed again.
Also would it be possible to bypass the anti theft system by adding a remote start, or cutting some wires. I just really need to get this truck running.
C/K :: 2000 Chevy K3500 Will Start Then Stop And Security Light Flashes
I've read tons of posts about the security system and passlock on the ignition...but my truck does not have a chip key, as the dealer even looked into the key issue with me. There is no chip or resistor on this thing at all.
So, with that said, I have the identical problem as the passlock system people do. The truck will start, then stop, and the security light flashes at me. That's the last thing I want flashing me at 6am when I'm trying to leave for work.
It only happens about once every 2-3 months, but I want to eliminate the problem as I have a feeling one day it's not going to start on me and then the real problems will start...
Silverado :: 2000 - No Headlights And Security Light Staying On
I have a 2000 Silverado 1500 4.8 liter v8. On my drive to work this morning the headlights and the cluster light shut off and the security light illuminated and has been on ever since . The truck will crank and run fine I have brake lights and turn signals and reverse lights. I have read that this problem can usually be traced back to the body control module. I located the TBC fuse under the hood and it was blown. so I replaced it with another 10 amp fuse and it blew immediately after I inserted it. So I am thinking if I am able to rule out a ground or bare wire somewhere then the module itself may just have to be replaced.
The next question I have is due to the security light staying on in the cluster all of the time. Assuming that I can continue to drive the truck while waiting to have the BCM replaced I would only need to ensure that I did not drive after dark as I have no headlights. But I am concerned that the security light being on all of the time will drain my battery. Do the security light remaining on will in fact drain the battery? And if so, is there a way to disable the cluster and door security light so that I may continue to drive it and not have to come home and disconnect the negative cable every
Pontiac - Grandam :: Security Light Come On / No Alarm Fob
When mother purchased car she wasn't given an alarm fob. She just locks the doors. One day the "Security" light comes on and the car acts like there is a kill switch on it. Can't seem to locate the problem. She purchased it used in another state.
View 7 RepliesFord F-150 (2004-2008) :: Security Alarm Go Off For No Reason
I have a 2007 F-150 FX2 and as of 8-10 months ago I started having the security alarm go off for no reason. I thought maybe I sat on the fob or something stupid but it is getting to be more often. The truck sat at the dealership for 2 days last week and nothing. They decided after lightly bumping the grille and it went off the sensitivity was too low so adjusted that up to a reasonable bump required. Well it went off last night at 1:30 AM, so I don't know what to do now. The service writer did say he had seen this and it was always a door sensor but having 4 doors which one??
View 1 RepliesSanta Fe (CM - 2007-12) :: Security Alarm Not Working After Replacing Actuator
Security alarm not working after replacing front drivers side actuator. Paid a local Mechanic to replace actuator and now the security alarm when you press the door lock twice on the door remote is not arming. When I press the door lock on the remote once, the doors lock. When I press it a second time to enable the alarm and to hear the horn nothing happens at all. Light doesn't flash and horn doesn't sound.
View 5 RepliesHonda - Accord :: 2000 - Security Alarm Goes Off At Random Times
The factory 'Security System' aka alarm, in my 2000 Honda Accord EX goes off randomly. When this happens the horn sounds and lights flash for several minutes at a time. This can happen several times in one day and then not happen again for days or weeks. The owner's manual says that the security system is activated when the doors are locked and will sound an alarm if a passenger door, trunk lid or hood are opened while the system is activated. The system is deactivated by using either a key or the remote transmitter to unlock the doors. My mechanic tried to disable the hood latch switch, but this caused the alarm to sound continuously. How to fix the problem or disable the security system?
View 4 RepliesSilverado :: 98 5.7 Chevy Truck Not Starting
I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
Silverado :: Cruise Control On 2002 Chevy Not Working
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
Silverado :: 1992 Chevy Truck - Module In Distributor Keeps Going Bad
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesC/K :: Chevy Silverado Z71 - Water Sound Under Dash When Accelerate
On my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 RepliesSilverado :: 1994 Chevy - AC Compressor Engages But No Cooling Really At All
The issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 RepliesSilverado :: 1993 Chevy 2WD - When Accelerating RPMs Go Way Up And Won't Shift
I have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
Silverado :: 98 Chevy Truck With 4L60E Has No Second Gear - Shift From 1st Into 3rd
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
Silverado :: 1993 Chevy RWD Lost Power And Acceleration
I have a 1993 Chevy Silverado rwd automatic 350 5.7. It died on me on the way to work this morning. It slowly lost power and acceleration. The lights and radio all worked. When I tried to restart, it tried to start but then just cranked like it had no fuel or spark.
I had it towed home and checked the following things. I removed the fuel filter, it is clear. I verified that the fuel pump was working by turn the key to the on position while the filter was off. Good stream of fuel. I verified that there was fuel to the TBI. Good spray while cranking. I verified that there was spark by pulling a plug out, connecting to the wire and cranking the engine. Spark seemed weak but there was spark. The front plugs were dry, but the rear plugs, especially #8 was very wet. I verified the timing by pulling the #1 plug, removing the distributor cap and checked the rotor position. I bumped the engine to get the #1 piston to the top of the cylinder and the rotor was point directly at the #1 plug wire. The cap, rotor, plugs and wires are only 1 month old.
I also tried to check the ignition coil by disconnecting the coil wire from coil, and slid the boot back to expose the contact. I held it just of the coil while the engine was cranked, but did not actually see a spark at the coil. I did not hear any arcing. I pulled another plug and checked for spark. Again i had spark. Just seems weak to me. I am on my way to the auto parts store to get a new coil.
Chevy - Silverado :: 2008 2500HD Front End Clunking
I picked up a very clean 2008 Silverado 2500 HD. W/60K miles. The vehicle has been very well cared for as I know the orignal owner. I have zero complaints with the truck other than an annoying front end clunking. Its very reminiscent to the intermediate shaft issues of my 2003 2500HD.
Basically when hitting very small road imperfections, I can feel/hear a clunking in the front suspension. I can also duplicate the issue by rocking the truck left to right with the steering wheel while going 20-30MPH. I figured, stabilizer links. I put the truck up in the air, & can't find a thing wrong. Links are tight as well as the ball joints & tie rod ends. Were these trucks know for a common clunk like this.
Chevy - Silverado :: 1996 Won't Shift Into High Gear
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 RepliesChevy - Silverado :: 1999 - Shakes Badly At Several Speeds
I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.
I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.
The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.
Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle
Silverado :: 96 Chevy - Misfires / High RPMs And Doesn't Go In Overdrive
I have a 96 chevy Silverado 4x4 5.7 motor and it does the same thing but it doesn't leave in first gear, it misfires and high rpms and doesn't go in overdrive. but if I drive a little while and turn it off, it's fine it acts like a normal truck would. then if my truck is off for more that a couple of hours it goes back to it acting up.
View 1 Replies