Chevy - Silverado :: 2001 2500HD 8.1L Won't Engage 4x4 Till High RPM
01 2500hd, 8.1L allison auto, push button 4x4. wont lock in until its about 2000 rpm then will release just fine. Just not sure of where to start looking for the problem. Actuator on the axle or in the transfer case or something else?
View 2 RepliesSilverado :: 06 2500HD Truck Won't Run After Battery Change?
I am having a bad time with my 2006 2500HD 4x4 with the 6.0. First the battery was beginning to act like it was running down, getting weaker and weaker every time I started up truck. So finally truck died at the gas pump. I pulled battery (optima red top), and took it over to NAPA to test. Battery tested fine on top posts, but was acting funny with the side posts.
So, I purchased a new Redtop, and installed and and clunk, truck wont turn over! So, back to Napa to buy a new starter, install starter, hook up battery and now the sucker turns over great but will not start at all. Truck threw 6 codes: P0335, C0035, U1026, U1041, C0040, C0055.
Wiring all looks fine, battery looks new, and I have changed nothing but battery and starter.
Silverado :: 2001 2500HD 8.1 L - Every Once In A While Engine Just Quit While Driving
My crew cab 2001 has 75K miles and is well maintained and garaged. Every once in a while the engine will just quit while driving just as if the key was turned to neutral all dash indicators light up but just quits running. Turn the key to start and hear the engine cranking but won't start. Sometime in park it just cranks however I noticed that when I move the shift lever into neutral and depress the brake it will crank and start sometimes.
I don't believe it's a fuel problem. Could it be a loose wire in the column?
Silverado :: 2001 2500HD 6.0 - Shifting Really Hard Into All Gears
I have been trying to self diagnose an issue with my pick up for a while now. I have an 01 Silverado 2500HD 6.0 that shifts really hard into all gears. I was told it was the transmission going out, so we replaced the transmission with a rebuilt one and it did nothing for the shifting issues. We then had the transfer case rebuilt which also did nothing for our problems. My father who has some general mechanic knowledge is certain that the free floating rear end is not turning with the correct timing for the transmission shifting. No check engine lights come on at all during these issues. When I took it to a mechanic he told me I needed a new transmission and blew me off when I told him it was just replaced.
View 3 RepliesSilverado :: 2001 2500HD 8.1L Engine Idling When Truck Is In Gear
I have a 2001 2500HD P/U with the 8.1L V8. I have owned the truck for ~5yrs and used it with everything towing. For about the last three years, I have noticed that when the truck is in gear (Either Rev. or Drive) the engine idle almost acts like it is missing. It doesn't do this at higher RPM's (say over 1K) while driving.
Last spring I did a tune up (Plugs and wires) and a few of the plugs had quite a bit of build up so I figured that was what was causing the issue. For about 1wk after the tune up it seemed to clear things up (at least I didn't notice it), but then resurfaced.
My question is: should the "Coil" parts that feed each spark plug need replacing, or could they cause this symptom? The ignition system on this truck is a bit different that what I am used to seeing, so I am not sure where I should start looking for the problem.
Also, there are no error codes being thrown.
Silverado :: 2003 2500HD - Code P1516 TAC Module / Reduced Engine Power
My truck is an 2003 2500hd with the 6l engine and 89k miles. From time to time I'm getting message "reduced engine power". Usually at the morning after 10-15 minutes after starting. I have to pull over, shut it off, wait few seconds then restart it. The ses light goes off usually by end of the day ( or after few hours ). When scanned by chevy tech showing code P1516 Throttle Actuator Control (TAC) Module Throttle Actuator Position Performance. I have new battery with new main cable. TAC Module was cleaned.
View 14 RepliesSilverado :: 98 5.7 Chevy Truck Not Starting
I have a 98 chevy truck that won't start. After it sits. It was starting after cycling the key a few times. But now it won't start. Could it be the pump? I hear it running.
Or could it be the regulator? It was running good after it started. No check engine light, no gas smell, and no rough idle.
Silverado :: Cruise Control On 2002 Chevy Not Working
The cruise control on my 2002 Chevy 1/2 ton Silverado doesn't work. Went to boneyard and bought a module but it didn't fix my issue. Borrowed a multimeter and tested the cruise control module plugin. The only pin that came up with a incorrect reading was the first brake test. It's suppose to have 12 volts with brake pedal up but showed about 30, so I changed the brake light switch. Still no cruise control.
Since I have a high reading on the brake pin, do you think I have a wire issue there or would my problem be in the multi switch wires by the steering wheel?
Silverado :: 1992 Chevy Truck - Module In Distributor Keeps Going Bad
I have a 92 chevy truck with a 350 engine that came out of a 93 chevy my problem is my module in the distributor keeps going bad when i spoke with the previous owner of the motor he told me that he had the same problem and advised me to change the distributor. So I took my distributor out of the original motor and put in but the problem still exist, also I have noticed that I have nearly twice the exhaust coming from the drivers side tail pipe as I do the passengers side.
View 1 RepliesC/K :: Chevy Silverado Z71 - Water Sound Under Dash When Accelerate
On my 1999 Chevy Silverado Z71, a gurgling water sound is present everytime I accelerate. Are there any other Chevy owners that have had this same problem? If so, how was it resolved?
View 14 RepliesSilverado :: 1994 Chevy - AC Compressor Engages But No Cooling Really At All
The issue I'm having is the A/C. When I got the truck the A/C was completely freezing. Recently however, the compressor was having issues not engaging and I fixed that by simply plugging the cord to the accumulator thing. . Now the compressor engages, but is not cooling really at all. It is an old truck and the compressor is a little worn from what I see maybe 2mm space when not engaged. I checked the levels of freon/coolant with a gauge and the amount is perfectly fine. Plus there seems to be no leaks.
View 1 RepliesSilverado :: 1993 Chevy 2WD - When Accelerating RPMs Go Way Up And Won't Shift
I have a 1993 Chevy Silverado, 350, 2WD. It has a 4L60E transmission. I just started having a problem shifting from 1st to 2nd. When accelerating the RPM's go way up and won't shift until I let off the throttle. Then it shifts into all other gears normally.
If I accelerate slowly. it will shift into 2nd at about 16 MPH. It will then shift into all other gears normally. I have replaced the Throttle Position Sensor, flushed the transmission and replaced the filter and fluid. This made know change in performance.
I am now suspecting that it might be the 1-2 shift solenoid. The check engine light is not on and everything else works fine.
Silverado :: 98 Chevy Truck With 4L60E Has No Second Gear - Shift From 1st Into 3rd
I have a 98 Chevy truck with a 4L60E. It has no second gear. I was sitting in park for about 10 minutes with the engine running, then put it in drive and it never shifted into second. It felt like it went straight to 3rd. I played with it manually until I figured out I had reverse, 1st, 3rd, 4th and torque converter lockup, just no second gear. My acceleration rate was medium and when I reach about 27-28 mph it would shift from 1st into 3rd. It has 230K on it so I rebuilt it with all the typical parts - frictions, steels, band, sun shell etc., still no second. I then pulled the pan back off and replaced the spacer plate and put in a shift kit. While I had it down I put a corvette servo in and did an air check. It worked fine. I could feel the band tighten.
Both the 1-2 and 2-3 solenoids checked good at 23 ohms. I swapped their positions to see if it would make a difference. I also checked to make sure the 1-2 accumulator piston wasn't stuck in its bore, the spring was new from the shift kit. It was fine. Put it back together...still no second gear. When I originally pulled the pan off for the rebuild, the pan was free of any debris and was very clean. I then drove it a couple of miles to a local transmission shop. They put their scan tool on it and drove it around the block. There were no codes and the ECM was calling for second gear. It doesn't sound mechanical since almost all the parts have been replaced, rebuilt or inspected that affect the 1-2 shift. It sounds electrical. Is there anything I have missed?
Silverado :: 1993 Chevy RWD Lost Power And Acceleration
I have a 1993 Chevy Silverado rwd automatic 350 5.7. It died on me on the way to work this morning. It slowly lost power and acceleration. The lights and radio all worked. When I tried to restart, it tried to start but then just cranked like it had no fuel or spark.
I had it towed home and checked the following things. I removed the fuel filter, it is clear. I verified that the fuel pump was working by turn the key to the on position while the filter was off. Good stream of fuel. I verified that there was fuel to the TBI. Good spray while cranking. I verified that there was spark by pulling a plug out, connecting to the wire and cranking the engine. Spark seemed weak but there was spark. The front plugs were dry, but the rear plugs, especially #8 was very wet. I verified the timing by pulling the #1 plug, removing the distributor cap and checked the rotor position. I bumped the engine to get the #1 piston to the top of the cylinder and the rotor was point directly at the #1 plug wire. The cap, rotor, plugs and wires are only 1 month old.
I also tried to check the ignition coil by disconnecting the coil wire from coil, and slid the boot back to expose the contact. I held it just of the coil while the engine was cranked, but did not actually see a spark at the coil. I did not hear any arcing. I pulled another plug and checked for spark. Again i had spark. Just seems weak to me. I am on my way to the auto parts store to get a new coil.
Chevy - Silverado :: 1996 Won't Shift Into High Gear
My dad's 1996 Chevy Silverado will not shift into hi gear. The truck starts up fine and he can drive it but for some reason it won't shift into hi gear. Him and I are clueless as to why it won't. He has a 1996 Chevy Silverado, 6.5 liter V-8 automatic transmission, and its a diesel. We really want to fix the truck ourselves so we are trying to avoid taking it to a shop.
View 2 RepliesChevy - Silverado :: Security Alarm / Horn Going Off Unexpectedly
I have a 1999 Chevy Silverado 1500 extended cab. Two nights in less than a week, my horn has went off in alarm mode. Is there another reason for this other than an attempted jimmying of the lock? I live in a decent neighborhood with lots of pole lighting. Someone told me the keyfob battery was dying but I don't have the fob.
View 1 RepliesChevy - Silverado :: 1999 - Shakes Badly At Several Speeds
I have a '99 Silverado 1500 with a 4.3L V-6 amd 188,000. It picked up a problem recently that's been stumping me. Occassionally, and for no reason I can sort out, it starts to shimmy badly. This behavior has come about at several speeds. Sometimes just cruising down the road at 35-45 it starts to shimmy and wobble and the steering wheel shakes as if a wheel is horribly out of balance. Other times this occurs at highway speeds - it's noticeable and alarming. The problem can last a long while; othertimes the symptoms disappear in a few seconds. The first time it happened I thought I had a flat or was about to lose a wheel - this is not a subtle problem.
I've checked several things and came up empty. No delamination in the tires and nothing out of round, but just to be sure I had the wheels balanced and rotated - the balance was spot on when checked. Alignment is good. Did those things, but the symptoms continued. The vehicle is high mileage so I put in on the lift and checked the front-end. The steering rack has a very slight amount of play and the hub bearings have a very small amount of play too - I'll get after those, but they're not causing this intermittent problem. Everything else is tight. Shocks are fine, brakes are fine, I checked the rear-end as well - everything is straight and true. Air pressure is set correctly. I checked the driveshaft for runout and play - that's not the problem. The truck has never been in an accident and nothing seems misaligned.
The truck drives like a new truck most of the time, then suddenly, on a smooth road, it starts wobbling around. I'm starting to believe the problem might lie under the hood. I had a problem some time back with misfiring and the truck bucking - this turned out to be a worn distributor. A new distributor, rotor and wiring solved that problem. But these symptoms are not similar - this is not a bucking problem; the entire vehicle starts to shimmy and wobble with the steering wheel vibrating back and forth. It's hard to tell, but I cannot detect any misfiring or rough running in the engine when these symptoms appear and I have no 'check engine' warnings.
Are there any engine/transmission/drivetrain related issues that could cause intermittent symptoms that feel like an out of balance condition? A few other facts:- I have noticed the truck is a little down on power lately- The fuel economy has dropped off - I used to do around 20, now I'm down to 16mph highway- (Very) slightly rough idle
Silverado :: 2000 Chevy Truck Won't Start - Security Light On
I have a 2000 Chevy silverado. I recently was having problems with the transmittion not switching correctly. Long story short the shop told me to fix the problem I had to put in
A new transmition as well as a new computer which I did, from another Chevy. It worked for a few days then The truck was not starting and had security light on. Had alarm specialist take look and he said the computer had to be reprogrammed. It was reprogrammed at merles. And was still not working. Its unable to start, starts at random once in a long while. ignition switch was changed and still gave same problem. Took to another shop they had a specialist take a look and he said the computer had to be reprogrammed again.
Also would it be possible to bypass the anti theft system by adding a remote start, or cutting some wires. I just really need to get this truck running.
Silverado :: 96 Chevy - Misfires / High RPMs And Doesn't Go In Overdrive
I have a 96 chevy Silverado 4x4 5.7 motor and it does the same thing but it doesn't leave in first gear, it misfires and high rpms and doesn't go in overdrive. but if I drive a little while and turn it off, it's fine it acts like a normal truck would. then if my truck is off for more that a couple of hours it goes back to it acting up.
View 1 Replies