Chevrolet - 2500 :: 1992 - Runs Rough At Red Lights And When Pulling Away From Stops
My pickup runs smooth 95% of the time. It runs rough at red lights and when pulling away from stops. It seems to happen more when the A/C is on.
View 3 RepliesChevrolet - Lumina :: 1992 - Engine Won't Fire After Ignition
Recently my '92 Chevy Lumina (115,600 miles) has taken to not "firing" after I turn it on. It has a brand-new battery and altenator so there's plenty of current. I usually try to get it running 3 or 4 times and if it won't go, I leave it so as to not wear down the battery. It's as if it's not getting any fuel and yes, I do have gas in the tank. I've had the pressure in the fuel pump checked and it was within normal range although on the low end. I can wait 30 seconds or 6 hours and eventually it will "fire" and run.
View 8 RepliesChevrolet - Lumina :: 1994 - Stalls When Warms Up At Stops / Overheating?
My 1994 Chevy Lumina drives great when its in motion but when it warms up it will stall when your at a stop light. It does great at a quick stop, like a short red light or a stop sign but when I am sitting at a long red light it just stalls. It will start right back up but this is annoying. Recently the car radiator was replaced, so the car over heated. What could the problem be?
View 2 RepliesLumina :: 1990 3.1 L Engine Misfire When Cold - Running Rough
I have a 1990 3.1L, multiport fuel injection (NOT sequential FI), which runs very well most of the time. However, when I cold start it runs rough (misfire) for about 1 minute (no throttle) or until acclerated. The is no misfire when running normal, but it might be running a little rough when stopped at a traffic light (in Drive, foot on brake).
I put new plugs and wires on, but it did not affect this problem.
I am not using coolant, or oil, the plugs that were removed were somewhat worn, enough that I expected to notice a difference after they were changed.
I have not yet (1) cleaned the MAF, (2) checked carefully for vacuum leaks, (3) checked for leaking injectors.
Since this is a 1990, OBDI, I can't say which cylinder is misfiring or how the fuel trims look etc.
Chevrolet - Lumina :: 1999 - AC Compressor Clicked On But Cooling Fans Not Running
99 lumina. Ac was not working. I added a few oz's and the compressor clicked on but cooling fans were not running. After 10 min of idling the fans did come on but went off after 1-2 minutes. It seemed like they were responding to coolant temp more than ac pressure. Do the fans run when the hi pressure rises to a certain point where the computer will turn on fans?
View 7 RepliesLumina :: Hard Starting And Running Extremely Rough After Thermostat Replacement
I replaced the thermostat and coolant now the car acts like it's running on 4 cylinders. It's a 1992 3.1. The car ran fine before I just can't figure out what I did. Its real hard starting ,runs extremely rough. And the cooling fans are coming on when cold. Disconnected the battery to to reset the computer. pulled the codes got 45 (rich).
View 6 RepliesFord Super Duty (1999-2016) :: 2000 V10 Running Rough And Cutting Out When Give It Gas
I have a 2000 Ford F-250 6.8 v10 that is running rough and cutting out when I give it gas but I can turn the key off and turn it back on and it will run right, what it could be?
View 1 RepliesAurora :: 97 Stalled At Stops And Also Running Rough
A friend of mine got this car cheap because it stalled at stops. It also ran rough. The fuel guage would go from empty to full. Yesterday the car stalled out and wouldn't restart for an hour or so and even then it started hard. I drove it home for her but it barley made it. I changed the fuel pump because the dealer that sold it thought that might be it.
It started and ran rough like before after installing the new fuel pump.... Then it stalled and wont start. It fires but it still wont start. If I step on the accelerator it backfires a little but still no start. I checked for spark at the plugs in the front and they all have spark but its hard to tell if its a regular pattern or not. So its getting fuel to the fuel rail and at least some spark but it wont start.
Ford - F150 :: 1992 - Running Rough At Around 30 To 40 / 60 And 70 MPH
My 92 f150 has been running rough at around 30 to 40 mph and around 60 and 70. It has a 5.9 v8. I have recently replaced the plugs, plug wires, dis cap, and fuel filter without it solving this problem at all. Someone said this could be my transmission or throttle body.
View 8 RepliesCadillac - Deville :: 1992 - Running Rough Again?
I have a 1992 Cadillac DeVille with 25,000 miles on it. It’s never been driven in the winter and garaged when not being driven.Last year, it was running rough, so I took it to the dealer. They changed the spark plugs and wires. There seemed to be some improvement after that. After about 500 miles, it started to rn rough again. I returned to the dealer who changed the spark plugs again and replaced two of the fuel injectors. Still no improvement. A few hundred miles later, I took it to a local mechanic. He replaced four more fuel injectors and there seemed to be some improvement.After another few hundred miles, the engine started to run rough again, the fuel dropped down from about 20 mpg to 10 mpg, and it stalls at traffic stops or if the brake is applied. After 30 minutes of idling it will use 5 gallons of gas. There are no strange odors or visible leakage.
View 2 RepliesHonda - Accord :: 1992 - Running Rough When It Shift Into Overdrive
Why would my 92 honda accord run rough when it shift into overdrive.
View 6 RepliesPassat (B5) :: 2003 - Check Engine Light Came On And Car Is Running Really Rough At Stops
I have an 03 Passat with about 70K miles on it. My daughter put rug in it this morning (about 7 gallons) and since then the check engine light came on and the car is running really rough at stops. While accelerating, it seems to be fine. It is also getting about 10 mpg less than normal. MIL codes: P0300, P0301, P0302, P0303, P0304, and P0171. He said the P03xx codes were related to misfirings on each cylinder. The P0171 is a bank 1 failure (?). What do those codes really mean and could they be related to bad gas? Sent her off in my TDI JSW so she's not out on the highway if the Passat decides it doesn't want to go anymore.
View 6 RepliesFord Ranger / B-Series :: 2000 3.0L Running Rough / Shuddering At Stops
I have a recently purchased 2000 ford ranger 4X4 with approx. 130,000 miles on a 3.0L. When I bought the truck, it was running rough while in gear at idle, after first putting it in gear, and when coming to stops, then it quit running all together. I started by replacing plugs, wires, and ignition module. I finally got it to fire up after that, but instantly noticed the tell tale white smoke from the exhaust. Needless to say, my oil looked like chocolate milk. Rather than having the heads machined and checked, I opted to purchase a new set of cylinder heads from Dover cylinder head.
I got those on this week and she fired right up. After a few oil changes to eliminate the residual coolant from the oil passages, she still starts and runs fine, although the idle is a bit rough while in park. When I place it in gear the idle gets a little rougher. After a quick trip down the road, I'm noticing a pretty solid shudder when coming to a stop, almost like it's stuck in 2nd gear, but I can't really tell for sure. Seems to shift fine going up through the gears, but coming down is when the issue is.
I believe I'm dealing with two separate issues, one being the rough idle upon startup that doesn't seem to go away, and two being the rougher idle upon stopping. I've read everything from EGR valve, idle air control valve, low fuel pressure, and a laundry list of other things, and I just don't want to start throwing money away chasing my tail.
Ford F-150 (2004-2008) :: Intermittent Rattle / Knock / Running Rough And Dying At Stops
I am working on a customers 08 F-350 5.4l has 135k on it. came in with a severe rattle/knock, running poorly, and dying at stops. ECM gave up 8 codes relating to the timing... Found the phaser replacement steps here on FTE and followed them and replaced the VCT solenoids since i was in there. Customer reported that he replaced the cam sensors already. Ran great for a day, and the next day when I pulled into the shop it gave me a rattle. Not as violent as before but noticeable. I special ordered the wedge and followed the replacement to a 'T'. I have no performance issues and no codes.
View 5 RepliesFord Aerostar :: 1992 2WD Keeps Cutting Out Like It Is Not Getting Fuel
My 1992 AeroStar 3.0L 2WD keeps cutting out like it's not getting fuel BUT...only after around 55 mph and after it warms up.
I first thought it was the fuel pump so I changed it. I didn't get a whole sending unit along with pump, I just dropped the tank and changed the pump...that didn't do the trick. Then I checked the fuel filter along the bottom rail and it's very clear flowing. Then I thought it might be the fuel pressure regulator. Ok, how many of you have changed the fuel pressure regulator? Man it was tough! I had to grind down an allen wrench to get room to turn those three allen bolts AND I replaced it while I was stranded on the side of the road!
Well, replacing that regulator didn't work either. I don't know where to go from here. It totally cuts out at higher speeds when it's warmed up. Could it be the oxygen sensor? It can't be the plugs. I don't think it can be the sending unit in the tank even though I changed its pump. Is there another fuel filter somewhere? I'm moving to another town and I have to get the van there.
Cadillac - Brougham :: 1992 - Stalling / Cutting Out When Run At Idle For 10 To 15 Minutes
I have a 1992 Cadillac Brougham Hearse (Eagle Coach Co.) with a 305 V-8 that I’ve been having the following problem with. It had gotten to where it would start up, run at idle for 10 to 15 minutes and start cutting out, sputter and then die and would not restart afterwards. The next day, go out, starts right up and same thing after idling 10-15 minutes, cuts out and dies. So, I immediately think, fuel filter and or fuel pump! So, I replace the in tank fuel pump, sending unit and the in line fuel filter. Results remained the same. I’ve even swapped out the coil, ignition control module (ICM), starter and fuel pump relays from a like car and am still having the same results. Fuel gauge is reading between ¾ and ½ tank of fuel. Wondering what to look at next?
View 4 RepliesChevrolet - Blazer :: Running Rough - What Is Normal Idle
I have a 1998 chevy blazer about 134000 miles v6 4.3 4wd.. This last two weeks my blazer been running rough. I like to know what is normal idle for that blazer. When at idle its 500- 550 rpm when in drive its 500rpm.
View 16 RepliesLumina :: 1992 3.1 Car Started Dying Going Up Hills Then Stalled Out On Level Road
Trying to figure out if she jumped timing or maybe PCM went out. Car started dying going up hills then stalled out on level road. Found coil pack for #3 and #6 bad and replaced it. Other's arced ok so I left them alone. Didn't work for starting it so I checked the fuel pressure and got 37psi with key on and engine off.What would cause it not to even try to hit? Considering maybe it's jumped timing or the PCM is going out.
View 14 RepliesLumina :: 1992 - Stalls Intermittently And No Start / RPMs Drop Rapidly
I purchased a 92 Lumina Euro with a 3.1 and 101,400 miles on it a little over two weeks ago. It has been having problems since I got it.
It stalls intermittently, typically after I drive to work, shut it off for two hours, and then start it to go to my next client(home health aid) sometimes it stalls right after starting it then, and/or sometimes when put in reverse and/or drive and occasionally at stops signs after the aforementioned problems occur. It has also stalled out twice after highway driving after the car is shut off and started shortly afterwards, for instance, when I ran into a tobacco store for some cigs.. After the problem occurs it usually drives ok if I continue to drive it awhile even if I shut it off for a short time and restart.. I added some fuel injector cleaner when I filled the tank but it didn't work.
After about a week of the stalling issues the car refused to start after dying and didn't start for two or three days. As I was unable to get an answer from the dealer my step-father, who went with me when I bought the car, called him and he said if I could get the car there he would fix it. So I borrowed a bundle to have it towed the 25 miles or so to the small town car lot.
His mechanic supposedly fixed it by replacing the TPS and the dealer informed me that they had cleaned the throttle body before I bought it and apparently the TPS needed replaced to. However the issues again started after one day of it running fine. I tired to get a hold of this guy again and again I get the voice mail and no return call so as soon as I got off work I drove it over there and again he said he would fix it. He had it for three days and I again tried to get a hold of him without success and he again answered the phone for my step-dad and told him they had ordered some kind of module that would be in Monday. So Wednesday he calls me and tells me that they didn't replace this module because when they took it out it tested good five times but they noticed some gunk build up at the contacts of the wires that hook to the module and now the car was fixed. Why did they order the part before testing??? This doesn't make sense so it throws doubt on what the man said. I went to get the car and when I got back to my town and went to get those cigs it died twice after restart and put into reverse. That was two days ago and it has been dying once or twice each day since then although it is somewhat better than before as it isn't taking as long for the idle to even out at sufficient rpms after I throttle it at idle or drive awhile. BUT now it seems to be sucking the gas hard and I am wondering if this guy just did some jerry-rigging because he sure isn't fixing it.
A few more details. The rpms drop rapidly when this occurs, it has a couple of times had a rough idle at the same time but more often the rpms drop and it dies.Sometimes if I use the throttle and keep it up around 1000 rpms for a short time it won't die. I have smelt a burnt smell a couple times when I shut the car off, like electric burnt, not oil burnt or stinky exhaust. Lets see, I felt a very brief loss of power feeling when driving on the highway on two different occasions, so brief that it was barely discernable. It runs over the halfway point on the temp gauge after driving awhile in town, seems a little hot to me but I read these cars don't kick on the fan till 220. Sometimes the rpm bobs a little up and down at idle and slow speeds and once the battery power dropped and popped right back up when it was idling funny and when it had that no start an acquaintance tested it by putting a screwdriver in a plug wire and pointing it towards the engine as I cranked it and he said it had no spark and it did crank every time I tried to start it during the no-start condition. It has also done a bit of surging from time to time when the prob happens. The car is recovering from the stall condition quicker than it did before since this last "fix" but still stalling.