Elantra XD (2001-06) :: Check Engine Light Will Pop On Occasionally And Code Reads Random Misfire
2004 Elantra AT ... 6 months ago top of the radiator cracked caused it to overheat and blow the head gasket and warp the head. Repaired that and compression is fine now. It ran great for 4 months but now it randomly stalls. at or near idle. Seems to do it more at operating temp rather then cold. Occasionally the check engine light will pop on and the code reads (random misfire). It acts just like it has been shut off. But immediately restarts.
View 3 RepliesCorolla :: 2011 - Check Engine Light On / Random Misfire
I have a 2001 corolla with 37K mi on it. The check engine light came on today. Took it to advance auto parts to read the code. It showed P0171 (System too Lean) and P0300 (Random Misfire). Called up a toyota dealer and the technician think it might be bad gas. I buy gas at name brand gas stations and sometimes from BJs. I am not sure if the problem is with gas. I also been up to date with maintenance.
View 14 RepliesNissan - Maxima :: 1998 - Service Engine Soon Light On / Random Misfire?
I have a 1998 Maxima with 57K miles on it. I just bought it about a month ago. Anyway, a week ago I noticed It felt very "choppy" when I shifted into Drive or Reverse. It felt like it was going to stall but it never did. The Service Engine Soon light has been on for about 3 weeks but now, when I go up hills especially, that light blinks. I can still drive it but I shift into Neutral at stoplights to avoid hearing the rough idle while in Drive. Went to Pep Boys yesterday - they had the car for about an hour and then informed me that they would need to keep the car for a full day because of the "complex issues involved" - especially concerning the codes. The codes they read were:
p0300 random misfire
p0325 knock sensor
p0440 evap emission
My car passed smog test abut 3 months ago. I can drive it OK it just is very choppy and so there's not a lot of power, especially going up hills.
Chevrolet - 1500 :: 1999 - Engine Just Died When Driving At About 40 Mph
1999 Chevrolet Silverado 4.3 ltr ....
I was riding along the other day at about 40 mph and my engine just DIED. No sputtering, jerking, lurching, etc.. I have a 1999 Silverado 1500 4.3.
Since then I've tried swapping the fuel filter out. When I took the old one off I did the blow test and could barely get a bit of air through it. Put in a brand new one. Still won't start. It cranks but it won't turn over. It's like it is starved for gas I suppose.
All electrical faculties are functioning seemingly normal. (Of course I have to charge the battery every time I want to try and crank it because it doesn't charge itself because IT WON'T CRANK!)
I've had to change the fuel pump twice in the past 2 years. The last time was about 5 months ago.
For the past week or two my "Change Engine Oil" light has been on even though I've had my oil changed a month ago.
Caravan/Voyager :: Check Engine Light Came On And Started Blinking - Random Misfire
I have a 96 Grand Voyager that had had sat for a year undriven or started due to being out of state. It ran like a champ when I parked it. Now I charged the battery and went for a drive on the freeway and my check engine light came on and started blinking. I had the code read it came back with 2 codes a P0306 and a P0300. I noticed that the cylinder 6 spark plug wire was arcing on the core support. So I replaced all the plug wires and spark plugs with Champion platinum spark plugs. I cleared the codes and took it on a test drive and the P0300 code came back. Is there anyway the old gas is causing the random misfire? or what else could it be?
View 1 RepliesDodge - Neon :: 1997 - Check Engine Light Has Been On And Causing Random Misfire
I have a 1997 Dodge Neon with about 153,XXX miles on it. My check engine light has been on and i know that is caused by a random misfire. But more recently i went to start my car and it started but ran for less then 10 seconds and died. I tried to start it again and it wanted to but wouldnt make the final step i guess. We checked my spark plugs and i had oil sitting in 3 of the 4 there are. We have tried starting it again after cleaning the oil out and it started on the first try, I am just afraid of messing anything else up so until we figure out why it did this to begin with the vehicle is off limits. My Fiance said we need to replace the spark plugs and a gasket.
View 4 RepliesPrius (2001-03) :: Warning Light Came On / Random Engine Misfire - Code P0300
Had this code show up after the warning light came on and then the light went away after two day, the car seems to be a little sluggish now. I have read that this is a random engine misfire and it could be a bad plug..
View 1 RepliesChevrolet - 1500 :: 1997 - Code P0303 / Misfire On Cylinder 3
1997 chevy k1500 ... I have a misfire on cylinder 3 that i cannot figure out the cause. The idle is rough, backing out after starting is very rough, it seems to pick up at higher rpms but once the truck upshifrts to the next gear it shakes like a leaf in fall. within the past year the engine was rebuilt all new seals a new fuel pump, new injectors, new everything practically. so far i have done the following:
compression test results:125-130psi
fuel pressure test results: 50psi once primed, 50psi with engine running, no immediate pressure loss after engine is shut off
new spark plug wires
new spark plugs
replaced all four o2 sensors
Lexus RX 2004-09 :: 2008 RX350 - Check Engine Light For Random Misfire On Cylinders 4 / 5 And 6
I have a 2008 RX350 with 68k on the clock. Received a check engine light for random misfire (P0300) and misfire on Cylinder 4 (P0304), Cylinder ,5 (P0305) ,Cylinder 6 (P0306). Question is what will be causing this to happen. I thought about changing the spark plugs to see if this is possibly the cause. but what else should i be checking?
View 1 RepliesSonata NF (2006-10) :: Random Misfire Code P0300 - Check Engine Light Flashing
I know it is a random cylinder misfire code however I started my car in the morning and it was fine I moved it and put it back in my driveway. I started it up later and waited for it to heat up i came back outside 10 min later and my check engine light was flashing and my car was shaking like crazy you could tell the engine was misfiring like crazy. I had under a quarter of a tank but not empty yet. I shut it off and turned it back on and it was still doing it. I drove the mile to the gas station the way it was.
Under partial throttle it was revving to 4500 and over 5, had to let of throttle to make the car shift up a gear. I filled up and started the car again performed fine after that however the check engine light was solid now and still on. I went to my local mechanic and he read that code P0300. I changed my spark plugs that day and they were crap the original spark plugs I have 65,xxx on my car now. Car is smooth now. I cleared check engine when i saw him first and it did not come back on all day even before i changed the spark plugs later that night. Why my light was flashing and why my car was acting like that till i filled up?
Yaris/Scion & Vitz :: P0300 Random Cylinder Misfire - Check Engine Light Randomly Comes And Goes
The check engine light keeps coming on and off on my 2001 Echo with the above code. The car runs fine and the check engine light randomly comes and goes. What would set off the check engine light, but not cause noticeable change in performance?
View 2 RepliesMazda - Protege :: Misfire / Engine Hesitate But Only When Idling
About two weeks ago I noticed the engine idle start to hesitate but ONLY while idling. I was sort of leaning towards the distributor cap or rotor but that didn't add up because in the past when either of these would go out the car would just die without any warning whatsoever. So I just kept driving it and then tonight when I started the engine it was hesitating a lot more than it had been and also hesitating during acceleration but would smooth out after I would reach and maintain 40mph. The CEL also started flashing on and off. I went ahead and replaced all the spark plugs, distributor cap and rotor with no improvement. Tomorrow I plan to replace the plug wires. The code it's sending is P0302 (misfire cylinder 2). If the plug wire doesn't do the trick and I can't find any leaks on the intake I'm going to try to figure out how to inspect the ignition coil (well, it shouldn't be too hard to figure out since I have two different shop manuals for this car.)
Another possibility for P0302 is low engine compression but I seriously doubt that's the problem because last time I checked the compression all 4 cylinders had above average compression. I doubt the plug wire is going to fix it since the wires only have about 20k miles on them and I don't think I have any leaks on the intake so where else I should look? Oh yeah, just remembered. I also put a stethoscope (actually a screwdriver) against the fuel injector for cylinder number 2 and it was clicking away just like the other 3 injectors so I guess the injector isn't the problem unless it can be faulty and still make the clicking noise. So should I check the injector with a meter or is the clicking enough evidence that it's working fine?
Chevrolet - Montecarlo :: 2003 - High RPM Random Misfire
Here's the deal with this car i just did head gasket, valve job, all new intake gaskets and spark plugs. Car idles fine and mid throttles fine but with high throttle it wont shift and flashes the random misfire light p0300 it seems to run out of power. I've heard everything from maf sensors to ignition coils and wires. i was just wonder a good place to start and good test to do. I have most testing equipment including scan tool so i can ride with it. o and all cylinders compression tested above 150.....
View 13 RepliesChevrolet - 1500 :: 2003 - Reduced Engine Power Light Along With P1516 Fault Code
I have a 2003 Chevy 1500HD 6.0L 4x4. I've recently started getting the "Reduced Engine Power" light along with the P1516 Fault code. I've checked all the wires going to the TAC Module, TPS, and MAP, all appear to be in good condition. The Throttle Body is clean and the "flapper moves freely with no sticking. I only have this issue when it is warm outside. Recently we've had fairly code days between 32-50 degree weather but on the few days that it has gotten warmer, I've had the issue. Since it seems to only happen when its warm, I believe it to be a moisture issue, but I'm not sure.
View 6 RepliesImpala - Chevrolet :: 2000 3.8L V6 - Code P0300 Multiple Random Misfire
I have a 2000 Impala with a 3800 V6 series 2 with 165,000 miles. The only code I had was a P0300 Multiple random misfire that occured off and on at first, Worse in the city Better on Highway. It would start running on half the cylinders and bogged down, with the check engine light flashing, after getting onto the highway it would straighten itself out at first. I thought i had water in the gas so i ran some heat through it. straightened out for a day then happened again so I thought maybe a should run some premium gas in it, The car ran like total crap until the premium was gone, so i thought maybe it's running too rich, I put 87octane in it and it ran great for a day or two, then it gradually got worse to where it would not straighten up on the highway, tried to die at stoplights and i had to drive it with 2 feet to get it home and park it. I've replaced the battery, spark plugs, wires, ICM checked good, coil packs are good, replaced fuel Pressure regulator, looked for arcing on the spark plug heat shields and it will not start. It turns over but doesn't try to ignite and when I get the slightest rumble of ignition, it backfires up through the manifold and I see a puff of gas or light smoke by the exhaust manifold.
The car had a vacuum leak around the intake manifold cover gasket and a leak on the fuel rail. I pulled the fuel rail off my impala, snugged up the rest of the intake bolts then disassembled the fuel rail, flushed it out and cleaned the injectors the best i could, then reassembled it. before i re-installed the fuel rail I hooked it up to the fuel lines outside of the engine and tried to start the vehicle. all injectors had a nice spray pattern. So i installed the rail and it still didn't start but it had more combustion than before although it's still backfiring like before. Checked the fuel pressure by turning the key on and the fuel pressure went to zero very fast. I blew the rail out with air so to make sure i didn't damage the regulator I replaced it with the old one, ran the test again with same results, so i reinstalled the new regulator. I performed the fuel pressure test a few more times while moving the fuel hoses and when i moved the back supply line the vacuum loss stopped then dropped to zero when i let off of it. So I replaced the fuel line connector and O-rings on the injectors. It no longer has a vacuum leak.
I cleaned the EGR Valve out and had no luck there, then I removed the Idle Air Control Valve-pushed the pintle in, re-ionstalled it and WooHoo! it started! Although it still ran like crap with the same random misfire I was still happy to hear it start.I pulled the plugs on it to do a compression test and all 6 cylinders have between 180-190psi so the engine is in good condition mechanically. I installed new plugs before getting the car restarted and when i removed them for the test they were covered in thick black soot after running for roughly 15 minutes max.
I have (2) 2000 Chevy Impala's so I've swapped sensors from my wifes car to see if it would fix it. I've tested the following MAP, MAF, IAC, coil packs and ECM. None of these made the car change. I believe it is a timing chain because the car has never had a new timing chain and is way overdue, but I haven't had a code for a crankshaft position sensor. Can the timing chain be bad without throwing a code? It's not out of time enough to change the valve timing because I had a good compression test but its not firing right and still has the multiple random misfire. I have not checked or received a trouble code for o2 sensors, crankshaft position sensor or cam sensor. Something has the timing retarded and is dumping extra fuel into the engine because my new plugs looked like they were in the engine for a year.
Chevrolet - Avalanche :: 2003 - P0300 Code / Multiple Or Random Misfire?
My 03 Chev Avalanche is giving me a P0300 code (multiple or random misfire). With no distributor or individual coil is this something I can fix myself or is it shop time?
View 6 RepliesFord Super Duty (1999-2016) :: 2011 - Service Engine Soon Light Came On - Hesitate While Throttling?
I have a 2011 f250 with the 6.7l diesel. Overall it's been fabulous. Descent mileage, and never ending power. The service engine soon light came on the other day. I have checked the fuel and dropped some additive in the tank. Have also checked the air filter which is good. There is a hesitation when giving it throttle. Then it shoots like a rocket.
View 6 RepliesChevrolet - S-10 :: Check Engine Light Come On / 4th Cylinder Misfire
2000 Chevy S10 pickup
Had the check engine light come on, and when I checked on the code it gave a 4th cylinder misfire. Autozone instructed me to simply replace my spark plug with a new oem plug.
I replaced the spark plug as instructed. After about an hour of driving, the check engine light goes off and I think, great! Problem solved. However, another hour of driving and the check engine light is back on again, without going away.
I headed back to autozone to get a readout, just to find that it's the same code. So I put another spark plug in. Same result - check engine light goes off after an hour, only to come back on again permanently after another hour.
Now, normally I would think, this must be the spark plug line that needs replacement,however I am sure there must be some clue in the fact that the check engine light turned off for an hour.
By the way, not sure if relevant, but I also found a lot of build up around the spark plug before I initially changed it.In fact, there was so much that I had to scrape around the plug with an awl, and blow out the crud with a compressor,just to get my socket into place without there being crud in the way.
Any clue what that check engine off/on clue might be?
Chevrolet - S-10 :: 1969 - Temp Gauge Reads Hot All The Time After Grounded The Sender Wire To Engine?
I have a 1969 chevy c10 pickup. One of its problems is the temperature gauge was not reading. I grounded the sender wire to the engine block to deterimine if the sender was bad, and ever since the gauge reads hot all the time, even with the ignition off. Could I have fried the gauge?
View 2 Replies