Yaris/Scion & Vitz :: 2003 Echo Throwing A Cylinder Misfire Code / Idle Rough
My friend has a 2003 Toyota Echo that is throwing a cylinder misfire code. Original code is P0302 and P0302PD. The car is idling rougher, kind of sounds like "put-put-put". Also, the car has no power at all. He lives on a hill and he can't even pull out of his driveway. Lastly, the smell of the exhaust is gassy.
We have changed out the spark plugs...no change. Next, we bought a new ignition coil for the number two cylinder...no change. So, maybe its the wiring. Put the new coil onto the number 3 cylinder and the number 3 coil onto the 2 cylinder. Low and behold, the misfire code changes to P0303 and P0303PD.
Thinking we might have gotten a dud of a coil, we bought another. Same thing...new coil on 2 code is P0302...new coil on 3, code is P0303. Could we just have gotten two bad coils? Oh, coils were a BWD brand coil and Duralast brand. Should we just go OEM from dealer? OR Denso from Advance Auto?
Yaris/Scion & Vitz :: 2003 Toyota Echo - Engine Shakes On Idle
I am buying a Toyota Echo that the engine shakes on Idle and the shaking increase a bit when the AC is On ....
View 2 RepliesYaris/Scion & Vitz :: Echo 2003 - Check Engine Light But No Code
Recently changed a front pipe manifold on my Echo 2003 4doors Five spd.
Noise I was reporting ealier thread seems to have subsided somehow but I did not hit the high road again, since the repair.
But I have this check engine light that went off 3 days ago and stays on.
Tried 4 times to read the code of OBd II reader and it pulls nothing. As if everything was normal.
I changed the batteries but it acts like it does regularly and it shows like there is no code to pull out.
Could that be a Ghostly Check Engine. It is still on at the moment meaning every time I drive the car.
Yaris/Scion & Vitz :: High Idle / ECT Was Out Of Range
I got a 2001 Toyota Echo 1.5L that was running rough on cold start ups. Got a trouble code saying the ECT was out of range, replaced that and after firing it up it started to hunt and had a very high idle, I unplugged the Idle air control and it still continued to hunt. I smoke tested it for vacuum leaks and no leaks. After plugging and unplugging things to see what made it disappear it now stopped hunting but maintains a idle of around 2000rpm in park or neutral, in drive or reverse the idle lowers to about 900rpm.
View 5 RepliesYaris/Scion & Vitz :: 2003 Toyota Echo Starts And Runs Good But Stops When Warm Up
I have a 2003 Toyota Echo with 250,000 miles. It has been a great car as I commute 90 miles to work. I have had no major problems with the car. Unfortunatly it recently died on the way to work. It was running great and then all the sudden it sputtered and killed. When I first tried to start the car it would just turnover but after waiting 10 minutes it started back up (this was a cold morning). When it started it was running great again. I drove it another 15 minutes and it all the sudden died again. This happened 3 times.
I have hooked up to a scan tool and a camshaft position sensor code displayed. I replaced that but had no change. Another code came up as mass air flow sensor. I purchased a used one of those and still no change.
I have started the car up numerous times and always have the same results. It starts right up, idles good, speeds up good and runs good at full throttle. The problem becomes when it warms up the car kills. If I run it at idle to a slow acceleration it takes longer to kill than if I run the car at full throttle. Once it kills it will not start up until the car cools down, but once it cools down it will start right back up.
Yaris/Scion & Vitz :: Toyota Echo Motor Start To Idle Really High For A Couple Of Minutes
I've always find solution to solve my little issues with my Toyota Echo 2004 Hatchback. Since last summer, my car seems to have a lot of problems to idle well with the fine rpm. Here are all the events :
-it all started last summer, when the motor would start to idle really high for a couple of minutes, before getting back to normal. When this happened, a p011 check engine would light up. I switched to synthetic oil, and it greatly reduce the number of time this happen, but it didn't solve it entirely. It usually happens when the motor is warm, but still not hot.
-Only once, during a long ride, I got a check engine. When I left the highway, my motor wouldn't stop idling high. stop/start the motor wouldn't change anything. I checked the check engine codes, if I remember well : p011, p016 and misfire. With a friend, we checked the crankshaft sensor, and it was really dirty, so we washed it, and it solved the problem! A few days after, I also change my spark plug because they were starting to be old.
-A few weeks ago, I started my car and it was idling high as usual to heat up faster (it is winter now). But then, the rpm suddenly drop really quickly. The rpm was really low for may be 2 seconds, and it nearly chokes, but just before it went up back to normal. Then low/high/low/high until the motor was hot. No check engine. I disconnected the battery for a few minutes, and when I reconnected it, the problem was solve. I also checked the air filter, but it wasn't dirty.
-Then, sometimes when I start my car, idling is fine but suddenly at a red light the motor start to run really low with a lot of vibrations and a bad smell. Stop and restart the motor solve the problem! But only until the next red light, or until the motor is warm enough. Still no check engine.
Yaris/Scion & Vitz :: 2002 Toyota Echo - P0171 Code Thrown While Idle
I have a 2002 Toyota Echo. I just purchases a Creader V code scanner. My car is throwing a P0171 code. The light only comes on at idle or while going under 10 mph.
The data from the reader was:
Trouble Code: P0171
Fuel System sta B1 : CL, using HO2S
Calculated Load: 11.76%
Coolant Temp 188.59 degrees
The Freeze frame data was:
ST Fuel B1: -3.91%
LF Fuel B1: 36.7%
Engine speed: 795.5 RPM
Vehicle speed: 0 mph
Intake Air Temp: 82.4 degrees.
I went back today and ran live feed on the O2 sensors. I'm not sure what STF of O2S: STF means. That was another figure displayed on my code scanner.
The O2S S1 was reading between .04 and about .82. The graph looked pretty normal (I guess) in regards to going up and back down between 0 and 1. I don't know alot about mechanics, but I seen a youtube video of a graph showing it going up and down and what is normal. Mine did that on S1.
O2S S1: STF was: 3.89 and -1.57%
O2S: S2 was a different story. It was between like .58 and .66.
The O2S S2: STF didn't give me a value at all. It just said " --% ". The graph of this was slowly going up but in a small range. It started at like maybe .4 and would go up to say .5. The next wave would be like .45 to .55, then .50 to .60, then .58 to .66 etc. So it was not ranging just between 0 and 1. It had a very tight range that gradually increased upwards.
I built my own smoke machine before testing with the code scanner and I didn't get any smoke coming out of the car except for around the air filter housing where the lid meets the bottom portion. I don't know if it's because I had the air filter wrapped in plastic wrap. Can I have an air leak where the filter cartridge connects that would case a lean code P0171? Maybe I should go try to smoke test again. I did it about 3 weeks ago and I can't recall exactly where I had the smoke going into. I thought I disconnected the PVC hose from the brake booster and plugged it in there. I assume the smoke would get thru the whole system. It took about 2 min before the smoke came out of the filter housing.
The car only sets a lean code at idle or going less than 10mph and I'm coasting in a residential area.
I have an inspection coming up in May and need to get this thing fixed before that. I can't find any other air leak, but I wasn't sure a leak around the filter would cause this and I'm not sure the leak wasn't caused by the plastic wrap.
I'm thinking my only other prob could be fuel related. Fuel filter, fuel pump, clogged injector, or can my O2 sensor be bad and causing this? I've already replaced all spark plugs and coils as well as the PVC valve and cleaned the MAF sensor with the appropriate spray.
The car runs ok. The exhaust seems to smell RICH. Like Gas. I don't think my fuel economy is as good as it use to be. It has dropped from as hi as 42 mpg to between 38 and 40 if I'm lucky.
Back when I was having problems before and realized I had a bad coil, I had tried some injector cleaner. Why the codes were back then, but I had erased them and the car ran fine for about 2 months and the light came back.
My MAF sensor was .14 lbs when I was watching the live data above. I plugged my fuel pressure tester directly into the fuel line coming from the fuel tank and got a reading of between 42 and 44 lbs (car not running, just by trying to turn the engine over). I don't know if that is as accurate (or useful) as having the fuel pressure tester on the car and in line to allow the car to start up and run and watch the tester. I have to wait until my part comes do run the test that way.
Yaris/Scion & Vitz :: CEL Comes On / Power Loss On Throttle But Engine Idle
I have a toyota yaris d4d (2002). My engine light comes on, I lose power on throttle but engine will still idle. I turn engine off for a few minutes, then restart, I then carry on driving as normal as if nothing has happened. This happens every 2 weeks. Error code is p1121(accelerator pedal position sensor range/performance problem). How to rectify it ...
View 1 RepliesYaris/Scion & Vitz :: 2007 - Check Engine Light Comes On With P0011 Code
I have a 2007 Yaris, 180,000 miles, The check engine light comes on. With a P0011 code. I know that that could mean either:
blocked oil passage
Mechanical timing fault
Camshaft position a timing over advance
Failed OCV
Or VVT controller assembly fault
Since it's been really cold out I figured maybe it was a blocked oil passage, but after an oil change and quick check - I no longer think that's the problem.
The car runs great and it doesn't seem anything is wrong at all ...
Yaris/Scion & Vitz :: 2001 Echo Engine Light Came On / Code P1349
My great 2001 Echo is acting up for the first time in 11yrs!.. This weekend I decided to have my mechanic change the manual transmission fluid and do a general inspection of the vehicle. He found nothing wrong. I decided that before embarking on a long trip, that I would change the oil/filter, flush the radiator and put new antifreeze, change the airfilter, replace the alternator belt, added a small bottle of Lucas complete fuel system and a new battery.
I was proud of my DIY performance except that the next day the engine light came on! I took it to AutoZone where I purchase all the supplies and battery and they came up with CODE P1349 which I researched and found out about VVT(variable valve timing) malfunction. Some of the reasons for this malfunction are: low fuel pressure due to clogged or bad injectors..... Fuel pump regulator....camshaft malfunction or ECU (engine control unit) problem.
1.This morning the light was off then ten or fifteen minutes later it went on and at the same time the iddle got much faster for about two or three minutes, (in other words the engine was running faster even when I took my foot off the accelerator) and then came back to normal.
2. Later on the light was off again followed by the same sequence of events. Then at one point later I could tell that the the engine was running fast again for a couple of minutes.
Yaris/Scion & Vitz :: Fault Code P1272 - Engine Light On In Dash
For some time I have engine light on in dash. I bought OBD scan tool and I'm using OBD Auto Doctor.
I had this engine light on for some time. It come on and goes off comes on etc.
So this is the fault - P1272
I didn't find much info about this code. There are two reading about this code. Either it's something to do with fuel pump pressure or something to do with one of the cylinders.
Car Toyota Yaris 1,4D 2006
Yaris/Scion & Vitz :: 2000 Echo Check Engine Light On / Code P0171
First owner, 192000 miles. Check engine light came on during last winter, I put fuel injector cleaner with gas and it went away for a while. It came back on, if i reset, I can drive for about 50 miles before it comes back on line. Also, may be two or three times a week, when moving after a stop, the vehicle stalls, i have to take the feet of the gas pedal and give gas again.
I called up the dealer asking for fuel filter and fuel injector parts prices. Fuel filter is in the gas tank and not meant to be replaced. The fuel injector I was told 4 x $155 each. For diagnostics they need $100
See attached, I was able to clean sensor 1. I could not unscrew sensor 2, the screw is rusted, plus there is no room to get a longer screw driver and turn.
Yaris/Scion & Vitz :: 2000 Echo - Heat Was Half As Warm As It Should Be
2000 Echo, I noticed the other day the heat was half as warm as it should be. The blower is still moving air the same as it always has. The upper radiator hose is hot, the lower is cold. About the same temp as the air in the 30's. The line going in to the heater core and coming out are both really warm. I thought is was the thermostat so I had it replaced to day by a local shop who does good work. The problem persists with the same symptoms. The car has yet to have the high temp light come on.
View 2 RepliesYaris/Scion & Vitz :: 2003 Echo All Coils Bad - Engine Lost Power
I was driving home and I lost power in my engine. When I gave it gas you can hear it miss fire and loose power I got it home and it starts and idles but not smooth. What should I be looking into at this point? I'll check the coils and plugs now but I'm not sure after that. I heard about a bad ecu but it still runs so idk.
View 7 RepliesYaris/Scion & Vitz :: Air Conditioning Blowing Cold In Town And Then Warm At Highway Speed
I have a 2006 Scion XB I purchased last year. Last week the air was blowing cold in town and then blowing warm at highway speed. I took it to my mechanic who charged the system (said it was a pound low) and said he did not detect any leaks. Now suddenly it stops blowing cold altogether. Not all the time. It blows cold in the morning. Then in the afternoon when I leave work it blows hot. But I can stop the car a few miles down the road, turn the car off, start it back up, and it blows cold....
View 3 RepliesYaris/Scion & Vitz :: High Pitch Noise When Using Heater
2008 Yaris high pitch noise when I used heater this morning.
View 1 RepliesYaris/Scion & Vitz :: 2003 Echo Running Rough At Low Speed - Engine Light Blinks At Acceleration
My car is a standard and was working fine not indication of any troubles. Stopped and pumped $20 gas. Started to drive and car starts running rough especially at low speeds. Going up hill is brutal. Engine light flash when trying to accelerate, slow getting up to speed, shudders- not a lot of power, once up to speed engine light turn off.
Press the gas to go up hill- engine light comes back on and it begins all over, it also sounds like it is not running on all cylinders.
Is there any suggestions: fuel pump, fuel injection...spark plugs and wires? Something more serious
Yaris/Scion & Vitz :: Automatic Transmission - Normal Idle RPM With AC On
What normal idle rpm is with a/c on with automatic transmission. Mine fluctuates between 680 to 710 with condenser fan on low and 900 when high speed condenser fan is on.
View 1 RepliesYaris/Scion & Vitz :: 2002 Echo Misfire That Goes Away During Idle
Mother in laws car had a bad misfire that goes away during idle. It seems to misfire during take off or slowing to a stop and Intermittently during cruise.
Came in with codes p0300 - random misfire and p0304 misfire cylinder 4
What I have done so far.
-Checked the oil
-Checked the plugs - they were bad so replaced them with ngk plugs
-part number - BKR5EGP
Misfire was showing in cylinder 4 on live data still
-Swapped coil 4 and 1
-Misfire moved to cylinder 1
-Swapped cylinder 1 with 3 to be extra sure and mis stayed on 1
-Swapped back to 4 and even 2 mis stayed in 1. Weird
-Pulled all plugs and checked compression getting 170psi
-Swapped plugs around in case 1 is faulty no luck
-Swapped number 1 and 2 injectors with no change.
So my thoughts now are leaning towards an ecm or a valve thing but would those not be on or off fails? It idles great and cruises great it's only bad we coming to and leaving stop.