Ford F-150 (2004-2008) :: 2006 - Lower Ball Joint Replacement?
I have an 06 F150 2wd that needs both lower ball joints. I've done searches and everyone keeps talking about a big freaking hammer. Can't you just use a ball joint press kit to remove and reinstall these? If no I'm gonna find someone to put them in for me because Im scared of breaking the aluminum control arm. There was also some talk of using some sorta glue on the joints as well.
View 8 RepliesFord 7.3L Power Stroke (1999-2003) :: 2001 - Upper And Lower Ball Joint Replacement
I have recently replaced both tie rod ends and found out when I took my truck for an alignment the mechanic stated that I had bad driver side ball joints (upper & lower) I confirmed this with SEARS and they stated that it was all the ball joints upper & lowers! the Haynes repair manual (1999-2010) states "ball joints on 1999 through 2013 2WD models were not replaceable".
View 4 RepliesLumina :: How To Replace The Lower Ball Joint
1999 Lumina / I need to replace the lower ball joint. The original one is installed by 4 rivets.
According to the factory service manual, you need to use 1/8 drill bit to open a pilot hole, then use a 1/2 bit to finish it.
LS / MKZ :: Changing Upper Control Arm And The Lower Ball Joint?
On a level-of-difficulty-scale from 1 to 10. 10 being the most difficult. How difficult is it to change the upper control arm and the lower ball joint?
View 3 RepliesSanta FE SM (2001-06) :: Right Front Lower Ball Joint Very Loose
I have a right front lower ball joint very loose and wonder if that ball joint press fits into the lower "A frame". And how is it removed ? What size fork tool needed?
View 8 RepliesFord F-150 - 1997-2003 :: Squeaky Lower Ball Joint
I have a 1997 F150 4x4 4.6 liter 140,000 miles. I want to replace just the lower ball joints but my service manual says you can't, that you have to replace the lower control arms. Is there any way around this?
View 5 RepliesPassat (B5) :: 1999 - Lower Control Arms Breaking At Ball Joint?
My daughter has a 1999 Passat 4cyl.... In the last year I've had 2 lower control arms at the front ball joints just break away. Lucky it has been when she was either stopping or at very slow speed.
On inspection this looks like a very unsafe design flaw. The aluminum control arm is strong except for the light metal around the ball joint it's self. If one of these let go at speed it could be fatal!!
What causes the break other than normal wear and is there any signs before one lets go?
Ford Super Duty (1999-2016) :: Doing Both Lower Ball Joint?
I need to do both lower ball joints. is there a write up or process to do it? do I have to remove the whole hub assembly/knuckle thing or can I do it with all that stuff in place?
View 4 RepliesFord Super Duty (1999-2016) :: How To Tighten The Nut On Lower Ball Joint
I have replaced my ball joints and now putting everything back together. I am having trouble tightening the nut on the lower ball joint, the joint turns with the nut as soon as it starts to get tight.
View 2 RepliesFord Excursion :: Leaking Axle Fluid After Ball Joint Replacement
Did ball joints this weekend and now have little axle fluid leaking out passenger side. was going to change axle fluid when i saw this so continued and when pulled the fill plug i would say 8oz or more came draining out. Did I mess up the seal inside the tube?
View 5 RepliesFord Excursion :: Noticeable Vibration At 65MPH After U And Ball Joint Replacement
I had the ball joints and u joints swapped out in my Ex a week ago and something's been bothering me. I get a vibration when cresting 65mph that I can't pinpoint. It's not violent and it doesn't appear to be in the steering wheels as it's straight and not jerking at all. It doesn't really affect anything that I can tell either... it's not the vibration from out of balance tires or cupped tires, it's just enough to be annoying... and a concern.
I can't tell if it's coming from the front or the rear either... just seems to be a hum that I can feel that wasn't there before the repairs where done. Where to start?
Sonata NF (2006-10) :: Lower Front Lower Ball Joints Freeze And Creak When Turning
Would bad lower front ball joints freeze and creak when turning. I have noticed that my car(2010GLS) with 108k miles has a creaking sound when turning the wheels left to right. I poked a hole in the rubber boot covering the joint and sprayed WD 40 in there and now it seem to creak even more. Guess I am going to replace the l and r lower ball joints.
View 9 RepliesFord F-150 - 1997-2003 :: Ball Joint Replacement / Control Arms Are Not Correct
I'm halfway through replacing the ball joints on my '03 F-150 4WD. When I pressed the new lower ball joint in, it's snap ring groove is ~1/8" above the top of the lower control arm surface. These are Moog 8695T joints. I've taken them in and compared with another new joint at the parts store and they seem to be correct. This implies that the control arms are not correct- they're too thin where the joint presses in. The old joints sat the way they should, with the snap ring flat against the arm. The old joints are definitely different than the 8695T's- they are shorter from the shoulder of the joint to the snap ring groove. I'm guessing that now I'll have to replace the lower control arms, as well.
View 11 RepliesFord Super Duty (1999-2016) :: F250 - Ball Joint Replacement?
OK, I've done a lot of things over the years on cars and trucks but never messed with ball joints on a F250SD 4x4 with 160k miles. Found out today when getting new tires that the ball joints are shot. I trust the shop but know I can do this my self. So if I'm going to do this what should I replace? Since I'll be doing this I want to know from those with more time under the truck than me what else should I be replacing at the same time. I have done the front wheel bearings and of course shocks. Just what am I in for and what other parts and brands should I be using? Bushing kits for stabilizer bar? Replace stabilizer bar with heavier after market?
View 12 RepliesFord Excursion :: 2001 - Constant Steering Corrections After Ball Joint Replacement?
I have a 2001 Ford Excursion. I had all 4 ball joints replaced and now I am experiencing poor steering and drivability. While driving in town and on the freeway I am constantly having to correct the steering. The car wants to dart to the right and then dart to the left. It will not drive straight for very long. Constant steering correction is very tiring, especially on long trips. Need to understand what is happening to my vehicle. What can I do to remedy the problem? The steering was not near as bad before the ball joint replacement.
View 14 RepliesHonda - Accord :: 2011 Sedan - Ball Joint Failure
The other day in our 2001 Honda Accord sedan, 4cyl, 140k miles, we were driving and the wheel became, how do you say, less attached to the car than it used to be? The wheel and the car had a nasty break-up and we were caught right in the middle of it. (see pictures) We were driving down a straight road, going straight, and boom, the wheel fell off and the car landed on one of the suspension bits . We were doing 30 and did fine. But we had literally just exited the freeway, where we were doing 70, a minute or two before this happened. Further, there was no noise, no vibration before this happened. The car was acting quite normally.
We had it fixed at a Honda dealership. We were on the road and it set us back $1070 and a full day. But there you are. So the problem is fixed, and I asked the dealership people to please inspect the other ball joints.
But...now I'm paranoid every time I drive the car. And I want to check them for myself. I read about the jack the car up and try and shake the tire trick. Is that foolproof? Is there more I can do to make certain that all the remaining bits that are supposed to be holding the wheel on are not, in fact, about to break?
Ford Super Duty (1999-2016) :: Tight Steering Knuckle With Ball Joint Replacement
My 2004 f250 ball and u joint replacement job is at a bit of a stand still. Tore it down, brought the knuckle and axle shafts to an ex mechanic I know, because he has a 20 ton Harbor freight shop press. He mostly used a hammer, bashed out the old ball joints (I already had removed the u joints). U joint turned out fine.
I did notice the upper ball joint protruded a very slight bit on one side in the knuckle, meaning you could feel with your finger on the underside of the joint and on the one side it is not exactly flush with the interior of the knuckle. I would say it protrudes no more than a thirty second or so.
I brought it home, installed the boots on the moog joints, (the bottom was unusually difficult to put on), greased the joints and hung the knuckle on the axle tube, by a few turns on the lower joints nut. I then inserted the camber sleeve on the top stud, torqued the bottom to 49 fp then the top to 67 and finally the bottom to 150. End result, very stiff movement on the knuckle. No tie rod attached, and it takes to hands to move it from the "stopped" position,(turned all the way). I am sure it is stiffer than when I did the other side.
I tried loosening the nuts completely, same stiffness. I redid the torque sequence, no change. Tried hammering the ears around where the joints seat no improvement. The fellow who installed into the knuckle came and took a look. He agreed the knuckle was stiffer than you would hope, but, he suggested Putting it all together, as he believed they would loosen up before too long. I am not sure whether to try that, or remove the knuckle now, and redo with new joints. Pros and cons to either approach.
My question is : Does a knuckle become more sketchy by the time it is dealing with the pressing of a third set of ball joints? If I finish the install now, will a stiff knuckle action lead to other mechanical wear within a thousand miles or so, while I wait to see if they loosen up?
Hyundai - Sonata :: 2006 - After Ball Joint Repair - Battery Died Twice
I just had a lower balljoint repaired on my 2006 hyundai Sonata. After 1 day, the battery dies. Had it jump started last night, and it's dead again this AM.
Could this at all be related to the ball joint repair? They don't seem related but it also seems like an odd coincidence since there were no other recent issues with my car. Thoughts?
Golf V R32 :: Ball Joint Bolt Broke Off
I was putting on the H& R sports springs tonight and was onto the last corner, front passenger when one of the 3 ball joint bolts broke off. It was so rusted that the nut didn't want to come loose. I used too much force and out came the piece. Do I just go buy a new ball joint at the local VW dealer and swap it out. I didn't touch the other two and the car is still driveable. It's the middle one, exactly as shown in this photo from the DIY.
View 6 Replies