Ford F-150 (2009-2014) :: 2011 - Slams Into 2nd Gear At Parking Lot Speeds?
2011 F-150, 5.0L, SuperCab. I usually only report odd things about my vehicles only after my wife says something. Didn't think about it really until she complained, keep in mind she drives a Subaru with a "CVT" transmission that doesn't shift.
What I noticed is that when driving at low speeds, say parking lot speeds my F-150 seems to slams into 2nd gear. when it does this it feels like you slightly got shoved in the back. Is this normal, I know it's a truck and there is a lot of rotating mass and torque going on here. My previous truck a 2008 Chevrolet 2500 HD, 6.0L felt similar at low, parking lot speeds, it also had a 6-speed trans like this Ford. Just wondering if this is normal for this beast.
Mazda - Brakes - Mazda3 :: Brake Failure Driving Slowly In A Parking Lot
Recently, the brakes on my wife's Mazda 3 (5 door, 2.3, 2005, 67k miles, automatic) failed while she was driving slowly in a parking lot. The pedal went all the way to the floor, but the car did not slow down. She used her key to turn off the engine (I've since suggested she use the parking brake instead). The car shuddered (presumably the engine slowing the car?) to a stop. She re-started her car and had some braking power, which returned to normal after a few pumps of the brakes. Since then, the car has been looked at by our usual mechanic and the dealer. Neither can find anything wrong and the brakes have been performing normally.
For it's age, the car is in good condition, has been regularly serviced, and has spent it's entire life in southern California. The only unscheduled maintenance I can recall has been the refurbishment of the electric window switches for the driver's door and some modest body work following a hit and run on the interstate (just dents and scratches). It's only other issues are an occasional rough idle when stopped at a light and harsh shifting from first to second or second to third gear when the car is cold (it's done this "forever," and I've always figured one of the accumulators was a bit sticky). The car was not serviced immediately before the incident. Is the car safe to drive?
Santa FE SM (2001-06) :: 2.4L - Pulsating Humming Noise When In Gear And Coasting
My 2004 Santa Fe 2.4L manual transmission with 200,000km on it has this hard to explain noise when in gear and coasting. This is when my foot it off the gas and say I'm going down a slight incline. There is a pulsating humming noise, worse in the lower gears that coincides with the engine holding the car back. This only seems to happen during coasting and not when down gearing to slow down. And even when coasting if I press even ever so slightly on the gas so the engine is not holding the vehicle back, it goes away.
The clutch has never been replaced and I'm somewhat assuming it may be the clutch becoming worn.
Prius (2010-12) :: RPM Slowly Goes Down When Coasting
I have noticed something about my 2010 Prius. Lately when I am driving the car for about an hour, the engine slowly reduces RPMs (based on sound) when I take my foot off the gas. The MPG indicator slowly goes from near zero to 100. Like VERY slowly. And that is just street driving below 45 mph. The car has almost 60k miles. Tires are correct and in very good shape.
View 11 RepliesSanta Fe (CM - 2007-12) :: 2010 - Engine Jerks When Driving Slowly
I bought a 2010 Hyundai Santa Fe 3.5L and noticed the engine would jerk really bad. It felt like the engine was going to jump out of the vehicle. I notice it does it when I turn it on in the morning and when I am driving slowly out my lane way the engine jerks. I have dealt with this problem since last year and they have already replaced the transmission which has done nothing. I took it back to the dealership and the service manager told me that he has already had 4 of the same vehicles come in with the same problem and they realized that they had to re-set the computer in the engine so that the transmission computer and the engine computer are on the same page that they talk to each other so to speak. Since they re-set the computer we have had the vehicle back a week today and this morning the car jerked again. I am tired of constantly taking this vehicle in and being told they have a solution and then it is not fixed. How am I supposed to sell a vehicle to someone when it feels like you are being lifted out of your seat because of the JERKING!!!!!
View 14 RepliesLexus ES 2013+ :: ES300h Check Engine Light On When Driving Slowly With Cruise Control
I was driving slowly with cruise control on when the check engine light came on, a few restarts and it still didn't go away. All fluid levels are OK, no other errors show up on start-up or driving and the car drives fine on both ICE and EV modes.
I'm bringing the car in first thing tomorrow. I called my usual Lexus guy and he didn't know what the problem could be either. I'm a bit freaked out, to be honest. Wish I had an OBD dongle to use with Carista.
Santa Fe (DM - 2013+) :: Water Dripping At Parking Spot
We've been noticing that upon pulling into and out of our parking spot, there has been water puddles and upon close inspection today after pulling our car into the parking spot, I looked under and saw water dripping. This is possibly A/C-related because we are running the climate control on auto every time we drive? Our car is brand new and has about 400kms on it.
View 6 RepliesAurora :: 95 - Slams Into Gear Hard Enough When Put Into Reverse
I just bought this problem child and I am having som trouble finding out why when you put it into Reverse it slams into gear hard enough that the nose dives down. I cant figure out why. Then RPMS are always low like 800 and it acts like its at 2500. It slamms that hard.
The 2nd issue is when I push the brakes there is a vaccum sound from under the dash and the brake pedal gets hard and the car does not stop well. I assume it is the brake booster but I have not tore the dash appart yet.. The RPMS dont drop out when the vaccum leak starts and thats what confuses me.
Elantra XD (2001-06) :: Slams Shifting From 2nd To 3rd Gear
I bought my 2005 automatic 4 speed Elantra knowing of this problem and feeling good about being able to track it down. how ever This did not stand to be the case. Start up cold shifts through every gear smooth as silk with know slippage or harsh shifts. roughly 10 to 15 mins after the car reaches operating temp on the gauge it begins to slam into 3rd gear only. Most of the time it is a double slam. Like bam bam real fast but indeed does shift into the 3rd gear then into over drive smoothly. I can duplicate it any time i desire to by merely pulling it back into 2nd gear and manually pushing the shifter back up to 3rd. it will slam every time with out fail. The man i bought it from told me he had this trouble and changed the transmission out with a 500.00 used one and did the exact same thing...
So I felt must be electrical wiring or TCM bad but upon examination i found no codes present to date. he threw parts at it and replaced both input and output sensors based off some thing he read on the net. also he said he replaced the TPS with a TPS from a wrecked car, still same harsh shift. he however could not remember how the fluid looked upon changing it and the filter as he also did that, nor can he remember what fluid type he used. I know shot in the dark right??? What is the actually fix such a hard slam when shifting into 3rd.
Santa Fe (DM - 2013+) :: Parking Assist And Blind Spot Detection Not Working
I just noticed this morning that both rear parking assist and BSD on my 2015 SFS Limited are not working. Other than the button near the shifter to turn off the audible alarm for parking, I don't recall any other buttons or settings that would turn both systems off. I won't have access to the user manual until later this evening. I did clean off the rear parking sensors but that didn't change anything. Am I missing something?? What's common? Perhaps a fuse?
View 12 RepliesElectrical-wiring - Engines - Gasoline :: 1997 Toyota - While In Gear And Driving Speed Slowly Drops
I have a 1997 Toyota Hilux (unleaded, not diesel) and I'm looking for input as she keeps breaking down but no one is able to figure out the problem. While in gear and driving, the gas stops engaging and the speed slowly drops. The car stutters while slowing down but then if I switch gears or rev the engine it will stop. After some time this continues to happen more frequently (at all speeds) until the car eventually stops and dies. Try to restart and the engine will turn over but not start. After sitting for a night or so, though, she starts up and runs just fine. Thus no mechanics have been able to solve the issue!
Could be a fuel problem as the exhaust pipe makes a banging sound when this happens, but it could also be electrical.
Ford - Transmissions - Explorersporttrac :: 2007 - Slams Into 2nd Gear After Trans Flush
I recently had my Transmission flushed at 90K (beyond the 75k). I had my Struts replaced and Full differential service. They found the Carrier bearing Center Ring was blown out said my truck was fine to drive until the part came in. I drove my truck home and it wasn't until I put about 20 miles on my truck did my truck start to slam into 2nd gear. It goes gentle if I accelerate slowly and eases with I turn the OD off ( but I only tried a few times). I have tried a few forums and there are so many things that it could be.
Everything was fine until I had this servicing and they took my truck apart. On a separate unrelated issue I have a check battery light on, but it is a brand new battery. I had my stereo changed out a year ago and the shop said it was the battery failing (only 1.5yrs old). Just though I would throw that in just in case a COMPUTER issue gets thrown out there. My truck has been running fine before all this SERVICING was performed...
Ford F-150 - 1997-2003 :: 2000 5.4L 4x4 - OD Hard Shift / Slams Into Gear When Give It Little Gas
I have a 2000 F150 5.4l 4x4. When I am going over 50 on the highway and I am in OD, if I let off the gas a couple of seconds later it feels as though the brakes come on because the truck slow down so drastically and when I give it a little gas it slams into gear. It feels as like there is a "gap" where nothing is engaged before it slams back in. This is a rebuilt tranny with less than 7K miles on it. I took it back once and they said it was the motor mounts. I had those replaced and still the same problem. I replaced the spark plugs 6K miles ago and the COPs 3K ago. There is 170K on the truck. I only drive about 8K miles a year.
View 2 RepliesCadillac - Seville :: Intermittent Stalling Occasionally When Slowing Down Or Coasting
I have a 1998 Cadillac Seville STS which has recently developed an intermittent stalling issue. Here are the details:
Happens occasionally when I'm slowing down or coasting, such as turning into a parking lot or going around a sharp entrance ramp-Has not yet happened during acceleration-No bucking or jerking while accelerating-No apparent warning that it is going to stall-Has happened once each of my last two trips
The first few times it happened my fuel level was pretty low, and one of the times I tried several times to restart it and it would start but die right away. I managed to get it started again, then I filled the tank and tested the fuel pressure at the rail, and I got 45-50 psi with the key turned but without the engine running.
After that time, I have not had any difficulty restarting it when it stalls. I held the valve in basically the same position that it is installed (meaning I didn't turn it upside down) and sprayed in the opening with throttle body cleaner (not carb cleaner). I then used a "pipe cleaner" to clean the inside, and I also worked the plunger up and down after I sprayed it.
I had a few "false alarms" in the past thinking it was fixed, so I wanted to wait until I was sure before posting. I now have to lose the habit of constantly glancing at the tach to see if it's about to stall. It would be interesting to know why cleaning the EGR valve fixed it.
Ford Super Duty (1999-2016) :: 2007 - Won't Shift If Does Then Slams Into Gear - Torque Converter?
I have an issue to where every once in a while my truck will not shift and when it does shift it slams into gear, and my overdrive light flashes and then I'll turn the truck off let it sit and crank it back up and it drives fine and the overdrive light is off. It shifts normal and smooth other than when this happens. Not sure if it is my torque converter or maybe a solenoid or what. My truck is an 07 f250 6.0 with 192,000.
View 5 RepliesFord 6.0L Power Stroke Diesel :: Runs And Idle Roughly - Stalls When Coasting / Parking
but 2nd time 6.0 psd owner. 2 weeks ago we picked up an '03 Excursion and were thrilled because it's been running like a dream and getting great mileage. However, according to my wife just yesterday, and after me driving it today, we have a big problem.
The engine starts, momentarily runs smooth, but then quickly becomes very rough. When trying to drive, it will make decent power, but it has an "off" feel to it, like it doesn't quite make as much power as it did, and it has a slight vibration to it.
Then when you coast to come to a stop, or pull in our driveway, it runs REALLY rough and badly, and usually stalls. I have begun the troubleshooting process. Here's what I know: Ficm tests good - 7 pin w/key on only gives ~46V (only tested w/voltmeter) Had an oil change done today and added a bottle of Hot Shot, will add the fuel treatment when we put more diesel in Believe ICP sensor to be OK. I unplugged it and no change Appears all injectors are firing since it ran down the highway decently, AND you can hear all injectors 'triggering' in a uniform manner with key on Turbo probably isn't sticking because made great power before, and decent power even with the problem NO Check engine lights / codes thrown
Details about the truck:Early '03 w/ 189,000 miles EGR delete done in a previous life w/ IPD kit Turbocharger replaced, in a previous life Headgaskets done, in a previous life (no ARPs though )
Questions & next steps:Even if there was no change w/ ICP unplugged, does that truly rule the ICP out completely? Could the IPR be the culprit?
Others? I have ordered a Scangage 2 and it will be here Tuesday. What's the first thing I should check? To me, this very much seems like an electrical problem; my gut tells me it's some kind of sensor or electrical signal error. What's the best way to investigate this path?
The engine turns over very well, and sounds very uniform so I don't think compression is the issue. Head gaskets have been done, although not with ARP studs. Batteries are very fresh and turn it over very fast. I have already learned a ton reading through these forums and just need some additional direction & brainstorming!
Santa Fe (DM - 2013+) :: Transmission Shifts From 4th To 5th Gear At Approximately 60 Km/hr
There is only one thing I don't like about our new SF. The transmission shifts from 4th to 5th gear at approximately 60 km/hr (36 mph +/-) and the rpm's drop to 1500 rpm. Now, when I want to speed up a tad (which is a frequent occurrence when driving around town), there is a pronounced hesitation before it drops back into 4th gear and accelerates.
In 5th gear at 1500 revs, I find that the engine is 'lugging' a bit. Yesterday, I started to compensate for this by changing to manual shifting as soon as the trannie shifted into 4th gear and leaving it there when I was traveling in that 60 kph speed area. For me, this is MUCH better and I quite like doing some of the shifting any way since I spent so many years driving manual transmission equipped cars.
How have others found the car to be when driving around town? Other than that, I really enjoy this car. Easily the most comfortable seats of any car I've ever owned --- their design provides terrific lumbar support and the new cloth material has a great 'feel' to it.
Santa Fe (DM - 2013+) :: Tranny Lagging In Particular When Shifting From 1st To 2nd Gear
I have a 2014 2.0T AWD Limited, now it's about 9000 kms so far with regular maintenance at dealer. Recently I have found the tranny is shifting a bit lagging, in particular shifting from 1st to 2nd gear. I didn't think it was like this when it was new, not sure if it's something wrong, or now I'm getting more used to the shifting and start complaining.
View 3 RepliesSanta Fe (DM - 2013+) :: Rough Transmission Shifts Mostly Between 1st And 2nd Gear
Just experienced something new in my less than a week old 2.0T. This morning was the coldest day since buying it (-15c). I had the block heater plugged in and it started up well. Let the engine run for my usual 30-40 seconds before putting it into gear. Reversed well, but was a bit slow shifting after putting it into 1st.
For the first 5 minutes or so of the drive, the shift were pretty rough. Mostly the shift between 1st and 2nd gear. Things got better after that and were fine for the rest of my trip and also an hour later when I came home.
Is this just a case of a very cold transmission and fluid, or is it something else? I've never owned a car that had such rough shifting in cold weather. Sluggish shifts yes, but not violent like these were.