Santa Fe (DM - 2013+) :: Tranny Slipping In 1st Gear At Around 3k RPMs
So dont know whats going on, but after my santa fe sat for a day, I went to go for a drive and when I left the house, the tranny slipped in 1st gear at around 3k rpms. The rpms just shot up, hammered into 2nd, then drove off as normal.
I couldn't get it to repeat it after that.
Facts:
-Car in eco mode
-Car sat for at least 24 hours
-Outside temp 70F
-slippage happened on takeoff at 3k rpm
-No CEL's
-around 11500 miles
What it could be? Should i take it in to hyundai? OR wait and see how it drives the next couple days.
Accent LC (2000-05) :: Tranny Shifting Into A Lower Gear And Get Stuck While On Freeway
My problems started out around the beginning of the year. Mostly, it was the transmission. It would slam really hard when shifting. Worst, sometimes while on the freeway, it would shift on it's own, for no reason, into a lower gear and get stuck. (Happened twice and was really scary).
Along with this, a couple times I would start it up and it would rev really hard, about twice what it normally would.
Usually, with the revving, I could turn it off and back on, and it would stop. A few times I could disconnect the battery, reconnect, and it'd be fine.
As for the tranny, I could turn it off then back on and sometimes that would work. Other times after a few miles it'd work itself out.
I did take it to my local Hyundai dealership. The first few times they couldn't get any code to pop, and they couldn't simulate the issue. It was very random when it'd happen. Luckily, on the 3rd try, they did get the tranny to shift hard. They said it was a bad tranny and replaced it (free due to warranty).
Unfortunately, that hasn't gotten rid of the issue. After a few months... maybe 3K - 4K miles the issue is back. Again, it's very random.
I've had the high revving which I've had to disconnect the battery to resolve. And the tranny is slamming again.
I don't notice any other issues. No engine light (except the one time the engine was revving really high and I had to disconnect the battery to reset, then the light went off).
Sometimes I can go a month with no issues. Sometimes it'll happen back to back days.
Could it be a computer issues? Is that something I can fix/change out as a novice?
Passat (B5) :: Tiptronic - Display Remains On Automatic And Shifting Up And Down Will Not Change Tranny Gear
My 99 V6 with Tip just started to malfunction this past weekend. By malfunction, I mean when I shift over into Tip mode, the display remains on automatic and even shifting up and down will not change the tranny gear.
I was driving with the cruise on and shifted into Tip mode to slow down for a toll booth ( slow to 25 and not stop all the way). When I got through the booth, I hit resume on the cruise forgetting I had shifted into tip and the car revved back up to 65 mph in 3rd gear for about 5 seconds ( I had the stereo cranking and couldn't hear the engine)before I realized what I had done.
I tried to upshift in Tip but it wouldn't let me so I had to go back to full auto setting where it works fine.
Is it possible to burn out a fuse or circuit of some kind by doing a dipshizit maneuver like that? The car runs great otherwise and still is getting low to mid 20's mpg in spite of the ethanol crap.
BTW, just had the computer reflashed last week after putting a new battery in because the Throttle Body was not working properly.
Jetta - Volkswagen :: 2003 GLS Lagging On Acceleration Right Around The RPMs When Shifting
I have an automatic 2003 Volkswagen Jetta GLS with 138,000 miles on it. I bought her four years ago with 91,000 miles. Right after I got her, I noticed that she'll jump a little when when she's cold (i.e. ease on the gas for the first few miles until she drives more smoothly). Looking around the web, this seems to be fairly common and most forums say that it shouldn't be a cause for any alarm.
More recently though, she's started to lag when I accelerate right around the RPMs where she should be shifting. For example, increase to about 3000 RPM, then it feels like a second of free fall, then she'll catch up and be just fine.
I took her into a shop to get it looked at about 3 weeks ago - initial thought had been maybe an issue with the transmission fluid (did a flush back in 2014 / 110k miles). The mechanic refused to do the flush until I had the catalytic converter and downstream O2 sensor replaced. The previous owner had installed a modification to the sensor and the wires had got too close to the converter and melted.
We noticed the check engine light about a year ago and had it looked at, but the mechanic then said it wasn't a huge issue and was really only going to affect our gas mileage so we held off. Since this mechanic was fairly certain that this was causing our issue, we went ahead and had the repairs made. No luck. Haven't had a chance to take her back to the shop, but I figured I'd ask to see if we were at least on the right track.
Second issue. My wife and I share this car, and her commute is significantly further than mine. She says that four times over the past two months the car has shut itself off when it comes to a stop. Not a common occurrence given the amount of driving we do, but enough to be concerning.
I've had regular oil changes and kept up with the routine maintenance over the past four years (new spark plugs, air filters, etc.). Just got a fuel system flush with the catalytic converter repair three weeks ago. Haven't changed the battery since I bought her, but every time we get the oil changed they check it and say it's good.
Santa FE SM (2001-06) :: 2004 / 3.5L Won't Start - Cranking Over Sound Is Lagging
I had the head gasket replaced along with all the other gaskets that come in the kit. new radiator, water pump, thermostat and thermostat gasket. blew head gasket at 78,000 miles. So now that has been taken care of, slowly everything else is going bad. recently, i pulled up in front of someones house and my suv turned off. When I tried to start it again it made a clanking sound and would not start. AAA'd it home and pulled the timing cover where the source of the sound was coming from. Seen the tensioner pulley loose and the belt loose. got it back on tdc and still does not start. the cranking over sound is lagging and sounds whiny. thought maybe was out of gas so i got gas and now when i try to start it it still is winding but it backfired and there was smoke behind the upper intake and still wont start. It wants to start, but doesn't.
View 11 RepliesSanta Fe (DM - 2013+) :: Drop Down In Transmission Shifting After Start Up
When the temperature drops below -20 Celsius, I find the transmission shifts weird just after start up. It seems like it goes into second, then third normally, then abruptly drops back into second. I'm pushing very lightly on the gas pedal, so the drop down is weird. A couple times the nav was blank on start up.
View 8 RepliesCamry 2012+ :: 2013 - Shifting From 1st To 3rd Gear Is Not Smooth
I have been reading some topics with people having issues with their Camry transmissions and torque converters. I have 15000 miles now and I'm noticing not as smooth shifts anymore from 1st to 3rd gear. It also jerks a little when you suddenly step back on the gas.
View 10 RepliesElantra GD (2013+) :: Weird Movement When Shifting Into 3rd Gear
I recently bought my GL less than a week ago with under 10km on it. Its been great so far but I noticed a weird movement when shifting into 3rd gear (both up and downshifting). It started happening about 2 days into driving the car.
As I shift into third gear I feel a little kickback against the forward motion. It doesn't happen all the time and it doesn't seem to be dependent on the car speed or the speed of my actual shifting. Although it happens a lot more when I shift quickly into third.
I've been told that 3rd and 5th gears are the longest and I might just need to get something adjusted at the dealership.
This kickback doesn't happen on any other gear except third (MAYBE I felt it a little on 5th but I may have been searching for it after being told about 3rd and 5th gear being long).
Jetta - Volkswagen :: 2013 - Acceleration Lag / Gear Shifting Not Smooth
My wife and I recently purchased a 2013 Jetta and have noticed some abnormal lag when accelerating. It's an automatic transmission and the gear shifts aren't as smooth as they should be. I have read that it is possibly related to the drive by wire system and may just be an inherent result of that system.
View 4 RepliesSanta Fe (CM - 2007-12) :: 2008 - Pulls To Right When Shifting To 4th Gear
Just had a new set of tires and a front end alignment done on my 2008 Santa Fe with 86,000 miles. Now when it is shifting into 4th or 5th gear it feels like your hitting a patch of Ice. The Truck veers off to the right for a quick second. It just seems like you can feel it in the left wheel. Other than that the truck does not pull and drives straight.
View 5 RepliesSanta FE SM (2001-06) :: Pause In Shifting From 1st To 2nd Gear With Squeal Between
I am hearing a slight squeal along with a slight pause between first and second gear. It only happens if I accelerate harder than usual. The tranny fluid was flushed and filled about 10k ago and fluid level and is still good. It's a 2002 2.7l fwd with 223,256 miles.
View 3 RepliesSanta FE SM (2001-06) :: Shifting Really Hard Into 2nd Gear When Going Uphill
I have an '03 AWD, automatic Santa Fe and it started shifting really hard into 2nd gear when going uphill recently. It also seems to take a while to shift into 2nd from 1st, but it doesn't bang like it does when downshifting.
In other threads on this site is seems like either the throttle position sensor or shift solenoids may be responsible for this. What's causing it, and how to go about fixing it?
Santa Fe (DM - 2013+) :: Slight Delay In Shifting - Codes P2562 And P2563
About a month ago, the Service Engine Light (CEL) came on and as a result there was a very slight delay in shifting and the Turbo did not engage at all. I brought it to the dealership for scanning. Error codes read as per work order:
P2562: Turbocharger Boost control Position sensor 'A' circuit
P2563: Turbocharger Boost Control Position Sensor 'A' Circuit range/performance
"The tech tested the pins and wires from the sensor to the PCM and all tested fine." Concluded sensor was faulty and ordered replacement part.
Once part was in, they performed the work to replace the sensor, test drove it and pronounced okay. By that same evening, the SEL came back on and the same symptoms developed. Brought it back the next morning and the same error codes came up. My dealership escalated the issue to the engineers with Hyundai and a couple of days later they replied with a possible solution.
From work order following:
"As per RO performed 11-20-007 Sonata Turbo EWGA inspection and adjustment form DTC P2562. Vehicle had under 4.1 V, adjusted rod from waste gate accordingly and road tested. Engine light did not come back on and vehicle operating normally".
I've waited a few days under normal driving conditions before posting and can state the the SEL has not returned and vehicle does indeed seem to be back to normal.
Apparently these symptoms are known for the 2.0T in the Sonata (i haven't verified this) which led the engineers to suggest checking the waste gate.
Santa Fe (CM - 2007-12) :: Transmission Slipping Near Gear Shifting Or Under Load
We have a 2010 Santa Fe AWD LTD with about 140, 000km on it. It recently came back from front suspension work. The suspension is fine now, but we notice harder shifts in the transmission. Also, there seems to be a vibration just before shifting gears and when under load (like going up hill) seems to slip (like on ice) about once every second until the shift is made. Once the shift is made it drive smoothly until put under pressure again. Even stepping down a bit on the accelerator will cause this slipping feeling (or maybe its loss of power). Just had new plugs put in and a tuneup so it's not that. Could something from the suspension work cause these symptoms?
View 29 RepliesSanta FE SM (2001-06) :: Shifting Rough From 2nd To 3rd Gear - Transmission Input Output Sensors
A few years ago my auto transmission in my 3.5 L engine hyundai santa fe started shifting rough from 2nd to 3rd gear, i did a trans flush and changed the input output sensors, anyway last week it started again, so i just changed the input output sensors again, it did not fix the prob this time, do you think a flush would work.
View 4 RepliesSanta Fe (DM - 2013+) :: Transmission Shifts From 4th To 5th Gear At Approximately 60 Km/hr
There is only one thing I don't like about our new SF. The transmission shifts from 4th to 5th gear at approximately 60 km/hr (36 mph +/-) and the rpm's drop to 1500 rpm. Now, when I want to speed up a tad (which is a frequent occurrence when driving around town), there is a pronounced hesitation before it drops back into 4th gear and accelerates.
In 5th gear at 1500 revs, I find that the engine is 'lugging' a bit. Yesterday, I started to compensate for this by changing to manual shifting as soon as the trannie shifted into 4th gear and leaving it there when I was traveling in that 60 kph speed area. For me, this is MUCH better and I quite like doing some of the shifting any way since I spent so many years driving manual transmission equipped cars.
How have others found the car to be when driving around town? Other than that, I really enjoy this car. Easily the most comfortable seats of any car I've ever owned --- their design provides terrific lumbar support and the new cloth material has a great 'feel' to it.
Santa Fe (DM - 2013+) :: Rough Transmission Shifts Mostly Between 1st And 2nd Gear
Just experienced something new in my less than a week old 2.0T. This morning was the coldest day since buying it (-15c). I had the block heater plugged in and it started up well. Let the engine run for my usual 30-40 seconds before putting it into gear. Reversed well, but was a bit slow shifting after putting it into 1st.
For the first 5 minutes or so of the drive, the shift were pretty rough. Mostly the shift between 1st and 2nd gear. Things got better after that and were fine for the rest of my trip and also an hour later when I came home.
Is this just a case of a very cold transmission and fluid, or is it something else? I've never owned a car that had such rough shifting in cold weather. Sluggish shifts yes, but not violent like these were.
Santa Fe (DM - 2013+) :: 2016 - Gear Consistently Dropping (Transmission)
I travel on the highway frequently and when I am cruising at 115-120 km/h my gear consistently drops from 6th gear to 5th gear then back to 6th gear. I am not pressing hard on the gas just keeping it at a normal pressure. This is the 2016 Hyundai Santa Fe brand new only 6500km. I brought it to the dealership twice already and they found nothing wrong. Saying there are no error codes when scanned and when they drive it nothing happens.
On my second visit I showed them a video of what is happening. It was two minutes long and within the two minutes my gear down shifted 3 times. So you can imagine when I am long driving how many times this happens. In order to get around it I have to shift to tiptronic and leave it on 6 gear so I don't get this down shifting incident.
Santa Fe (DM - 2013+) :: 2015 2.0T Engine Surging Or Shaking When Stopped In Gear
Not a great definition but have recently noticed an engine surging or shaking feeling when stopped in gear. About 7000KM's and it just started.
Pull up to a stop, foot on brakes and it randomly gives you a sensation the the motor is revving or stalling. You can feel it in both drivers and passenger seat. Haven't been able to see if the changes during this.
Just had it in for service a month ago which shouldn't matter but it seems new since then. Possible flash changed something maybe I don't know.
It's also intermittent so we all know how that works for service/dealership visits. Everything's fine didn't notice it...