Santa Fe (CM - 2007-12) :: Codes P2187 And P2189 After Replacing Fuel Level Sensors
So a couple days ago i replaced the fuel level sensors in my 07 gls 2.7 liter santa fe and all was well for 2 days. I had finally driven it enough that the codes cleared from active status and the car turned off the cel. However, during the same ignition cycle the engine started missing a bit and the cel came back on and started flashing at me. Codes found now are p2187 lean bank one and p2189 lean bank two, plus p0302 misfire detected cyl 2. I've tried the carb cleaner trick looking for a vacuum leak.. but no luck. Air intake boot is good vacuum lines look good etc. What might be going on? Did i get debris in the tank and glog an injector with it? Fuel pump itself appears to be operational. No bogging down or loss of power under heavy acceleration.
View 1 RepliesSanta Fe (CM - 2007-12) :: Invalid VIN Error Code Shown
Check engine light is on, when I went to get my car inspected it was showing an invalid vin code. How do get this off so I can get my emissions done?
2007 Santa Fe SE
Santa Fe (CM - 2007-12) :: Error Code P0057 - O2 Sensor Replacement
I need to replace O2 Sensor which is Bank 2 Sensor 2 which needs to be replaced.
Where is this located on a 2009 Hyundai Santa Fe 3.3L
Santa Fe (CM - 2007-12) :: Error Code C1627 - ESP Light Is On And 4WD Blinking
I have an issue in my car (Santa fe 2011) and it occurred since it was new (ODO 3000 KM , ESP light is on and the 4WD Blinking) . the agency could not resolve the issue. and my car up to now been in and out from the workshop for more than 6 times . and more the error code ( C1627 ) that appears in the GDS(Global Diagnostic System) does not exist in the system (troubleshoot manual) .
View 5 RepliesGolf IV R32 :: Error Codes P2187 And P2189
Add a few codes come up today ... P2187 & P218. Bank 1 & 2 running lean at idle
Haven't been able to find a definite answer..
Replace purge valve?? (P/N?)
MAF??
Fuel filter??
I keep getting engine codes and 265 miles per tank.
Santa Fe (CM - 2007-12) :: 2008 - Misfires On All 6 Cylinders
Just replaced all 6 plugs after getting p0300-p0306 codes. Still getting all codes, always starting with p0305. Was told coil was bad cause the shop only was getting p0305, but I have all misfire codes. We have over 95k on it, have owned since 2008. Its the 2.7 in it.
View 11 RepliesSonata NF (2006-10) :: CEL Came On When Driving After Restart - Code P2189 And P0153
I have a 2009 Sonata 3.3, 80,000 miles. After getting fuel I stopped about 2-3 miles away, when driving after a restart threw a CEL. Went to autozone and they gave these codes (P2189 and P0153) and were telling me possibly O2 sensor or Vacuum leak. Engine seems to run fine. Not sure if related but while fueling, gas pump was sputtering and I thought oh no. Wonder if I got bad gas and if it could throw these codes? I have since threw a bottle of Techron in and drove about 5-7 miles. I have had major work done with Timing covers twice. So it is possible a line may have came off but that was a few thousand miles ago. I pulled the cover and looked for any visible hoses off, did not see any. Don't want to spray with carb cleaner since it is dark out. I am still under the 100,000 warranty, so not sure if this would even be covered or not or whether I am doing irreparable damage. I saw other posts mentioning PVC issues?
View 6 RepliesSanta FE SM (2001-06) :: Error Code P0446 Came On
I've checked the lines from the Purge Valve on the Passenger side of the Intake Manifold, Check OK
I've Checked that Valve OK
I've Replaced the Canister Close Valve
I've got the Gas Cap tight.
I've removed the rubber bushing holding the CCV to the Evap Canister, hoping to isolate the Filter and point the blame on it, no luck there!!
I'm thinking next is to drop the Tank and check over all the Goodies on top.... as much as I hate the thought of that, the two access holes under the seats, just don't allow access to enough of the tank!
any thing there that I could suspect, I see there's a check valve!
There's also the Fuel Tank Pressure Sensor, which may be at fault.
Tiguan :: Rattle Coming From Engine Upon Acceleration Or Around 2k To 3k - Pending Code P0341
Last year my wife and I purchased a 2011 certified pre-owned tiguan from a local VW dealership which will stay anonymous atm. This past weekend we were driving home and noticed a rattle coming from the engine upon acceleration or around 2k-3k. The EPC light and check engine light both flash one time whenever this happens but never stay on. I scanned the car and found a pending p0341.
I know about the timing tensioner so I waited until the car cooled completely and went outside about 1am and started the car, sure enough it made the star-up rattle.
We took it back to the dealer and they diagnosed it with a failed timing chain and camshaft and are going to replace the components. I'm guessing by failed timing chain they mean the tensioner.
Elantra XD (2001-06) :: Check Engine Light Came On While Driving - P0341 Code
I own an 04 Hyundai Elantra with around 196,000 miles on it, and have run across a problem I haven't had to deal with before. A few days ago, my check engine light came on while driving. I didn't really notice much, but when I started it again it began idling roughly. I got it home and pulled the code, which was P0341 (camshaft position sensor). This isn't the first sensor I've had go on the car (I replaced an oxygen sensor and throttle position sensor a couple years ago), however I ran into two problems:
1. How likely is it that it's the sensor that's bad as opposed to something like the timing belt or VVT adjustment?
2. Since the sensor isn't horribly expensive, I decided to try replacing it, but I can't get any socket to fit on the bolt that secures it. I've heard it's a 10mm, but nothing seems to fit snugly. Maybe there's just so much crud and corrosion that it's ruined the head. I tried using an extraction socket, but no luck.
Ford F-150 (2004-2008) :: Code P0341 - Replaced Both Cam Sensors Still Bad Miss
I have a 2004 F150 5.4L 2WD auto. I had the cam phasers and timing cover done at the end of 2014 and the truck was great. Back in december, I parked the truck and when I started it the next morning, there was a horrible miss. I left it parked a month or two, then tried starting it up last week. Nothing.
So I had it towed to the shop. They found the starter was bad, and the only code it was throwing was P0341... Cam sensor bank 2. I had it towed back to my house, replaced the starter and the grounds and fired it up. It had the worst miss on the planet and died shortly after being started. I replaced both cam sensors, and now it starts right up and runs... but still has a bad miss.
I used my scanner and its still throwing A P0341 code almost instantly. It sounds like a bad miss that slightly gets better when you give it gas... but its not throwing any misfire codes or anything.
Santa FE SM (2001-06) :: 2003 - Error Code P1159
It seems that i'm most likely going to have to replace the entire plenum .
P1159 here are some details. [URL]..................
I've checked all connecting wires and none appear to be loose. When the issue started to occur and prior to discovering the P1159 code, I also replaced all coils. I replaced the coils because one was arching over to the metal of the engine. I assumed this may be my problem. The issue still persisted obviously. The check engine light never came on so I assumed I wouldn't get a code. I took it over to a friends house with a code reader and that's when I discovered that it was actually giving the P1159 code.
Are there any other model cars that utilize the same engine that I could use the plenum from? Getting this in working condition is going to be the difference in what I can get for it.
Golf/GTI VI :: EPC Light Flashed For About 5 - 7 Times And Service Engine Message / Code P0341
Code 0341 (cam sensor?)On my way home epc light flashed about 5-7 times and message saying service engine. 111,000 miles and just had intake manifold replaced and plugs and coils not to long ago. I have been feeling a slight hiccup at cruising speed and twice my gti has just shut off while driving. New fuel filter as well. I searched the forum and didn't come up with anything specific. Can I just replace the cam sensor or is there more to it than that.
View 1 RepliesFord 6.0L Power Stroke Diesel :: No Crank Mainly During Colder Temps - Code P0341
I've got a no crank issue this morning. This truck has done this randomly off and on, mainly during colder temps, but normally if I hold the key in the start position for a few seconds it will crank. This morning, no such luck. Batteries are good, everything has power, I can hear the starter relay clicking when I turn the key to start but it won't turn over. It never does this during warm weather. It got down in the low 40s last night and it's rearing it's ugly head this morning. The only code is the P0341, camshaft position sensor, but I don't know if that would be the cause of this or not. It's a starter issue or the CPS?
View 4 RepliesSanta FE SM (2001-06) :: 2003 - ABS Light Comes On / Error Code C1274
I have a 2003 diesel GS Santa Fe, every now and then when driving the ABS light comes on, not very often but it does, if I switch the ignition off and restart it goes out, I had it on a fault finder computer and it showed code c1274, I think its something to do with the G sensor and the way it breaks (ABS) is it an easy fault to fix? What are the costs involved and will it affect the driving of the car, like I say it rarely comes on and I don't notice any change in how it drives.
View 1 RepliesSanta FE SM (2001-06) :: 2003 2.7L Engine P0113 Error Code
So the check engine sign came up on my car and using the OBD it tells me the error is P0113. After googling the information, it looks like I have an issue with IAT sensor.
I opened the air filter and what I believe what could be the sensor and there was nothing clogging up, so I'm assuming the sensor needs to be replaced
Question is where is the IAT sensor located and how do I dis-assemble it so I can replace it. Is it the piece that is located just before the air filter?
Santa FE SM (2001-06) :: Error Code P0455 - Oil Leak In Engine Bay
I just joined the forum mainly to care of my dads 2001 Hyundai Santa Fe but also I got a check engine light on my way home from work last night.
From last night I saw that oil was all over the timing belt. Today I inspected it with a Coworker and his OBD II reader.
Error Code was P0455, EVAP - Evaporative Emission Control System Leak Detected (gross leak).
Now the oil leak is stronger since the oil spills is on hood (inside hood). I will make a picture tonight when I get home.
I personal think it's leaking from a tube/ valve on top of the timing belt (picture will show more tonight). Thinking of cleaning the timing belt area, then drive a little around or leave it in idle to spot where the leak is from.
Common issue? I googled around but since P0455 is a common issue (on my 9-2x as well) I couldn't find anything about this I am also limited from my search since I am currently at my work PC incl. strong firewall.
I will see if google let me find a picture...
Santa FE SM (2001-06) :: Engine Light Error Code U0d00
Engine light come on and everything is running great, this morning got this error code U0d00. Went to advanced auto and had them run a scan.
View 5 RepliesSanta FE SM (2001-06) :: V6 Showing Error Code P2100 - ETS Relay?
My Hyundai Santa Fe 2006 V6 3.5L shows error code P2100. I cannot for the life of me find the ETS relay. Ive scoured the net but just found vague drawings and pics that didn't show ETS relay. I would also like to know is the ETS relay also known as the fail safe relay or is that a separate relay. Ive seen pics of the fail safe relay but none for the ETS relay. If there is such a relay, exactly where it is located?
View 2 Replies