Golf IV / Jetta IV :: Slam Driver Side Door / Fuel Pump Primes / Starts Then Stalls
I have been without my dub for over a month mk4 gti/golf awp motor 1.8t manual transmission and have ran multiple scans and replaced multiple parts. I am suffering from a no start condition, start and stall immediately, and have troubleshot many problems.
Most recent vcds scan results are: intermittent door module fault (not faulty, not implausible, "intermittent") (j386) Speed sensor implausible (g28) (already replaced with no change) open circuit or short b+ fuel level sensor fault.
I have had the driver side door taken apart on multiple occasions and found: no cracked joints on the pcm of the LOCK module (solder covered by brownish/gold sealant?) Two breaks, 1 in the ground and 1 in the hot wire between the chassis and the door and since applied electrical tape to the chafed part of the door wire harness. I have ran multiple scans since applying the tape with various results.
After applying a maintainer and verifying full charge on BRAND NEW BATTERY I ran scan with above codes.
I have in the last month replaced coolant temp sensor, fuel filter, fuel pump relay, above mentioned battery, and installed toggle switch to lock module micro-switch, speed sensor. About 5-10k miles ago I replaced the fuel pump with vemo brand from ecs tuning and fuel pump relay.
I have re "seated" and cleaned all terminals, below and on the battery as well as on the transmission, have "checked" the ground just in front of the ecu and removed enough parts to place my hands on it to check for a loose condition. Also checked ground on top of block next to coil packs. I've checked pillar a for chafing and the ground next to pillar A and the ground just below the CCM.
I have also taken a mallet and attempted to re create this door slamming condition by tapping everywhere around the door jam on the chassis and door with no change. Also with the door LOCK module removed, I have tapped on it to see if pump would prime, no change...........
After sitting in my recaro imitation cloth seat totally defeated I realized that the intermittent fault code was pointing the "integrated window motor/DOOR module" that was the only thing I hadn't attempted to "test" (originally thought window motor was only a window motor)
Verified continuity to the door module, and verified continuity to relay panel, fuel pump and lock module........... Also tapped on the DOOR module itself with no change.
Piece the whole door back together, slam the door and bam fuel pump primes........... (also massaged the repaired-chafed wires before and after re-installing back into door, with no change/prime.) After sitting a while sometimes it will prime by itself......(with any of the 3 fuel pump relays I have for this car)..
Replacing 1 fuel part after the other over the 4 years I've owned the car has temporarily resolve my issue, until now. (Also have tapped around gas tank/retainer ring on the pump to see if fuel level sensor fault was a culprit). I don't believe this to be the issue because I've netted this fault in the past and has never cause a no start condition or come back after clearing when replacing fuel related part.
After slamming the door I have noticed the pump primes in waves, like a hum hum hum instead of 1 solid hmmmmm and when the car DOES start (when the pump primes) the pump continues the hum hum hum condition before dying. (I have gone as far as a test drive and I rev the engine and put in gear but acts as if i have a bad clutch, all rpms, no horse power like it's slipping condition from a bad clutch
immo light goes off when key in on position, epc and check engine light are off after car STARTS when slamming the door. With key in on position hear a loud click under hood (relay station I'm certain) but the throttle body buzz's until the chime sounds with door open (have not tested this when it DOES prime.....)
Passat (B6) :: Starts But Then Immediately Stalls
I've had this intermittent issue for a while where the car won't start properly. What seems to happen to me is that it starts properly, but then immediately stalls. Normally during a start it will start at about 1200rpm then quickly idle back to under 1000 and then slowly reduce some more. Now at about the same time as I would expect it to idle back to 1000rpm it stalls. After this happens, it seems like I can keep reproducing the failed start over and over again if I try to start the car again. If I wait 30 seconds or so and then try to start it, it usually works.
On two or three occasions I got a warning on the dash about faulty steering lock. Checking in VAG the only errors shown are related to those, no other codes. This has happened many times over the course of perhaps two months. It's been colder during this period, but generally it seems the error happens more often when its a little warmer weather and not really cold. Lately I've been inserting the key part way, waiting a few instants for things to initialize and then starting and it seems to work every time.
Ford F-150 - 1997-2003 :: Truck Starts And Then Immediately Stalls / Idles About 3 - 4k RPMs
If I don't keep in the throttle immediately after start up it will stall a lot of the time. It doesn't do this every time or if it sits for a while but if I drive it and then stop off at a store or something and then go to start it back up it gives me this problem. I notice it idles about 3-4k RPM's when I stop at a light or something too.
View 14 RepliesJeep - Cherokee :: 1987 - Starts Immediately If Relieve Fuel Pressure At Fuel Rail
I have a 1987 jeep cherokee with inline 6 and multi port injection.
Sometimes this vehicle only starts when hot
Some times only when it cold
I have recently fixed the fuel leak.
When its hot or cold and not starting if i relieve the fuel pressure at the fuel rail, in most cases it will start immediately. However if fuel pressure relief does not work. I disconnect the vacuum line at the what looks to be the EGR valve or the pressure regulator at the front end of the rail, then usually starts right away.
I have not tested at this time to see if the fuel pump is failing nor have i tested fuel pressure. I am trying to narrow down the problem to one specific part. There is no problems with cranking. There is spark - coil, plug, dist cap have been replaced.
It seems the problem is with fuel delivery of sorts. It was mentioned that sometimes the heat from the engine could be heating the fuel rail to a point which turns the fuel into a gas not allowing it to atomize.
Ford 6.0L Power Stroke Diesel :: F250 - Cold Starts Fine / Stalls Immediately After / No Throttle Low RPM
I'm having an issue with the truck not staying idle after cold start up. The truck will turn over and start right away (not even 2 second crank) but immediately dies. The throttle will not work at low RPM. When I start the truck, it will instantly rev high, the revs will drop low, it will try to compensate and rev high again, then it will immediately die.
If the RPMs are under under 2.5k, the truck will immediately stall and die. When I attempt to use the throttle under that RPM, it will not work. No matter how much I depress it, the engine will instantly cut and stall out. It will not attempt to deliver fuel. The only way I can get the truck started is if I rev the engine high and hold it. I need to hold the truck at 2.5k+ RPM for atleast 30 seconds. It generally takes me about 5 tries to finally get it running (mainly due to the throttle immediately cutting out and I have to 'catch' and hold it.) After that, there is no sign or issue. The truck will start immediately back up after it's been running for a couple minutes.
CEL: MAP sensor (0069?) -- Sensor is spotless. Harness looks fine. I replaced the injectors, both batteries, and the alternator this summer. It doesn't sound to be any these either as the truck sounds extremely healthy and immediately turns over.
Ford Super Duty (1999-2016) :: 2001 F350 V10 Stalls But Fuel Pump Stays Running?
I have a 2001 f350 v10 that has been giving me fits. has 88000 miles. cranks and starts when cold or fuel pressure is below 40 psi. SES light will flash when it stalls and fuel pressure goes from 30 while running to 40 and the fuel pump runs continuously when this happens and truck will not start. replaced crank sensor and fuel pump was changed about two months ago. if I relieve fuel pressure it will start and run for short time then stall and fuel pump stays on. all fuses are good. I am at a loss.
View 1 RepliesFord - Explorer :: 2002 - Either Stalls Or Starts - Runs Rough And Then Stalls With No CEL - Water In Fuel?
We've had two problems within the last week with our 2002 Sport Trac (4.0l SOHC engine w/167,xxx miles). They may be unrelated, but I suspect there's good change they are. Both incidents happened while my 16 yo daughter was driving, so there's only very limited info on what happens. Both times, when I get there, it starts and runs fine. There is no CEL.
The first time it apparently stalled as she neared her destination after driving only about 2-3 miles at 35 mph or less after a cold start. She was slowing to pull into a parking lot and reported the dash lit up with warning lights, no power steering assist and no power brakes and no power from the engine. When I arrived it started and ran normally. She had fulled up the day before after two days of heavy rain, so I suspected water in the gas. I drove it more than 200 miles within the next 24 hours under a variety of conditions and filled up at a different station. I experienced no problem what-so-ever, and didn't bother adding any dry gas.
Then 5 days later (still on my fill-up) when she tried starting it after sitting all day, she reported the engine started but ran rough before stalling and never idled normally.
Doesn't the fact there's no CEL eliminate a lot of the upstream part of the control system......like sensors and actuators? This leaves things like the downstream parts of the fuel and ignition systems. I.e. from the fuel tank / pump to the injectors and the downstream parts of the ignition system.
What are the possible culprits? Fuel pump, fuel pressure regulator, injectors, ignition module, spark plugs, and....... what else? (I'm not that familiar with what these engines have) And of the possibilities, what are the most likely causes.
Santa FE SM (2001-06) :: Fuel Pump - No Power
2001 Santa Fe. 4 Cylinder
It has spark, it will run briefly with starting fluid.
The camshaft, crankshaft, fuel pump and TPS are all good.
All fuses are good.
The fuel pump relay is good.
The FP relay gets power to both the control side and the FP power in side.
If I jump the FP power side of the relay it will get 12v pump to the FP connector.
NO power to the FP cutout switch by the master cylinder.
So, how can the relay be good and the FP get power if I jump the relay but not have power when I put the relay back in? Is the ECU cutting it out as soon as it gets a signal from the relay?
Ford Super Duty (1999-2016) :: 2001 F250 Occasionally Starts - Fuel Pump?
I have the gas 5.4l in my 01 F250 Super Duty. I had to change out the leaking Heater hose before I could attack this other issue. The truck starts when it feels like it. I changed the fuel filter and it started fine. Then the next day it wouldn't. Later it would. However each time it does start it dies when throttled up. I am down to thinking it is the fuel pump. My question is, because changing the pump sucks about as bad as changing the heater hose. Can I install an inline fuel pump and deal with the sump pump in the tank later? Are there any Cons to doing this?
View 5 RepliesSanta FE SM (2001-06) :: 2004 Won't Start - No Power At The Fuel Pump
Santa fe 2.7litre 2004 240000km... My santa fe won't start, after check we found no power at the fuel pump. we change pump, we found a bad contact at the remote starter connection. we decide to cut the wires of remote starter. after the car start and ride 1 day, stop with check engine, towing
We take off the remote starter and disconnect all wire of this remote starter. The car start and stop. After that bizarre problem, the park light stay open, and the window can be up and don't with no key in the ignition!!!!
We check fuse relay etc, all wire of the old remote starter and we take off battery and rebuilt the ground. We still have the same problem; when we tried to start at acc, everything seam normal but the wipers run at off position and when we turn the key for starting , wiper stop , radio close.
Like we have a ground problem. We change the ignition little baril now we think the computer is maybe dead. I double check all remote starter wire and every thing seem ok !!!!!
Santa FE SM (2001-06) :: Engine Won't Start - Fuel Pump Reset?
02 Santa Fe was recently in a minor accident that popped the airbags. Engine won't start now. Where do i find the reset for the fuel pump?
View 3 RepliesFord Excursion :: Start Then Die Immediately - Fuel Pump?
As in a previous post, i have been having issues with my truck starting then immediately dieing if i dont keep my foot on the gas.
Ive learned how to drive with 2 feet because of it, but I'm afraid i might be doing some type of damage since it keeps dieing and I have to keep starting it.
Once i get going for about 10-15 minutes its fine but its happening every time i start the truck.
Before it starts running correctly, it only idles around 400 rpm.
I think its the fuel pump, since my mechanic put a code scanner on there and it didn't throw any codes, he thinks it might be the fuel pump.
My question is, should i go with a ford pump from the dealer or are the ones sold from discount/o'reilly/napa just as good?
Santa FE SM (2001-06) :: Fuel Pump Hums When Turn The Key To On / Cranks But Won't Spark
My Santa Fe quit running one day as I was driving. The fuel pump hums when I turn the key to on. The spark plugs look ok. One coil is not getting a spark. We replaced that coil and it still isn't sparking. The timing belt appears to be fine. I bought an OBD II reader, and it gave me the code for the camshaft position sensor. We replaced that today, but there is still no spark. I cleared the code and tried to start the car. There are no codes present so I am assuming I fixed the camshaft sensor issue. Next up on the list is to replace the wiring leading up to the ignition coil. I gave it a quick look over. It appears to be ok, but I might replace it anyway. The outer housing is cracked a little, but the car is 13 years old so I expect that. Before it died there was an awful sound coming from the engine. It sounded like a piston was rubbing/scraping. I am throwing that out there just in case it is related to my electrical issues. I have noticed other weird electrical issues as well. The middle brake light usually works, but sometimes it doesn't work and sometimes only part of it works.
View 4 RepliesSanta FE SM (2001-06) :: Growling Noise When Turn The Key To Prime The Fuel Pump
Instead of a normal humm I get a growling noise when I turn the key to prime the fuel pump.. I am think fuel pump issues.. but no sure if thats what it is??
View 9 RepliesSaturn - L200 :: Fuel Will Not Go Into Tank / Pump Immediately Shuts Off And Gas Spills Out
So it has happened twice now that gas will NOT go into the tank on my 2001 Saturn L200. The pump immediately shuts off and gas spills out. From some research I believe there is a kinked hose but where and why did this happen 2 months ago and then now after several fill ups between. The first time it happened the problem fixed itself after sitting for a day, I guess I'll find out today if that is the case.
View 3 RepliesGasoline - Pump - Chevrolet - Corvette :: Starts But Stalls Out 20 - 30 Seconds Later
My car runs great except occasionally after I drive awhile, park and than restart to continue, it starts right up but stalls out 20-30 seconds later. I turns over but will not run. I have to let it sit for 30-45 minutes and than it starts up like a champ. I suspect fuel pump but would like an expert opinion. Garage says they can find nothing wrong and to bring it in when it happens... how do I do that.
View 1 RepliesSebring - Chrysler :: 2001 - Engine Starts Then Immediately Shuts Off?
A couple of months ago my daughter's Sebring engine began shutting off immediately after starting. We brought the car to my usually reliable mechanic. They couldn't find anything wrong. The problem became more frequent (every 2 to 3 starts) and we brought it back to my mechanic who determined it was the car's computer system. $1700 later the car is ready to be picked up, my daughter gets it after the shop is closed, and it wouldn't start! She left it there, got a ride, and, one week later the Sebring is still at the mechanic's. They told us it starts every time for them and they don't see any problem. After researching on the Internet I thought it might have something to do with the immobilizer but they told me that tested fine. I'm at a loss over what to do.
View 2 RepliesElantra XD (2001-06) :: 2002 - Gas Pump Cuts Off Almost Immediately After Start Pumping
So for about two months now, every time I get gas, the pump cuts off almost immediately after i start pumping. After that, I am able to pump about a second or two before the pump shuts off. It recently has started spitting gas back out of the tank (I'm assuming it's the gas I just pumped into it being spit out). I'm not sure what is wrong. I have not gotten into an accident, there is no smell of gas in the car, the gauge still works fine, and no check engine light on.
View 3 RepliesTiguan :: Low RPMs / Almost Stalls - Bad Fuel Pump?
Every so often when I leave the car sit for 30 minutes after being driven, I start it up, put it in reverse and back up, then when I put the car into drive the RPMs drop for two seconds or so and it seems like it wants to stall. After that happens, all is well and the Tig drives normal.
I scanned the Tig and it came up with a "low fuel rail/ fuel pressure" code. It happened 5 times.
Is my fuel pump going? Maybe a dirty fuel filter? Or maybe a computer problem?
Info: Tig has 26k miles on it, stock computer (not chipped), it is out of warranty. I only run 93 octane in it too.