Santa FE SM (2001-06) :: Idling High And Started Surging
2002 santafe 4x4 v6. about week earlier I had a cel for temp sensor voltage high. so I replaced it. then... my power steering cooling loop by radiator started to leak from corrosion and for some reason my coolant gauge was reading about a needle with from the red. (maybe from getting ps fluid on it? idk) so I went to investigate why it was leaking and I thought the cooling loop pluged into a cooler on radiator so I removed my lower front engine mound and motor mount by the timing belt so I could raise engine up a2" to get a better look. when I saw it was just a loop and that was my leak I ordered replacement. It came in I swapped it out. Pretty easy . Decided to do a radiator flush and replace thermostat. Why I was at it. I drained radiator and took the old thermostat out. was gonna leave it out for the flush to cycle better. When I started it up it was idling around 4k rpms. I figured it might be because of thermostat so I put the new one in.
Started it up and same thing.... I check all the vac lines I could find all were tight. I unplugged them one at a time at throttle body/intake tube and blocked it off with my finger and it was still idling high. It also started surging. going from 2k to 4k and going back and forth. I checked the maf and it was clean as a whistle. No leaks on intake pipe. If I put my hand over maf it sucks the tube towards the throttle body. no air leaks anywhere. Took off iac valve its clean. I plugged the holes where it is on tb and started it up and no change in what its doing. also the throttle body flap is closed the hole time. Iac seems to be properly opening and closing. when I watched it after I unbolted it. I sprayed brake cleaner all over manifold to check for air leaks no change in high idle. I also took off the evap valve hose to tb and plugged it at tbody and no success.
I checked my sensor connectors and there tight and no wires are pulled out. I have yet to check cam sensor connection. (does it have a cam sensor?) I unplugged battery over night. this morning it ran at 2k rpm for two mins then surged to 4k. could it be my throttle position sensor? is there a way I can check with multi meter? Ive done a lot of research and it seems like a common problem with Hyundai but people don't leave a what fixed it post after they figure it out. they just leave the threads hanging. I hope I can figure this out.
When I get home tonight Ill plug where the brake booster vac line goes in. I looked at the hose and it was super tight and didn't seem to be leaking but maybe booster is idk. Ill also check wires to all 02 sensors. but if o2 sensor wire was broke wouldn't it throw a cel? Also no check engine light. but id did have an abs light come on the other day. was thinking maybe an abs sensor at the wheel but I am not sure. That light was on for a week before this issue started. It was never revving up until I started working on the other issues from my research I am guessing throttle position sensor. I am going to multimeter it tonight.
Santa FE SM (2001-06) :: Idling Very High When Put In Park Or Neutral
My 2001 Hyundai Santa Fe has recently started idling very high when put in park or neutral. While in drive the engine idles above 1K and you need to keep your foot on the brake to keep from moving forward. If you shut down the vehicle while idling high, the car will not start right away. It needs to cool down for 10 -15 minutes before restarting. It will run fine for awhile but will go back to revving up again.
View 7 RepliesSanta FE SM (2001-06) :: Surging Upon Startup And High Idle RPMS - TPS Replaced
2004 Santa Fe .... 2.7 6 Cyl 4WD 150k miles
Recently I started experiencing RPMs surging upon startup and driving before my engine warms up. The problem has gotten worse to where I push on the accelerator the RPMs jump to 2700 and the transmission feels like it disengages. My initial thought was the tranny was going bad and slipping. I checked the fluid level in the T and found it was maybe a half Qt. low. I topped it off, but this had no impact on the problem. On a side note, I am able to use the manual shifting feature on the "His and Hers" Shifter and drive the vehicle without any issue. Transmission works fine in manual. The surging RPMs which only occur in Automatic mode, triggered the CEL and I got a code of P0123 which is high side voltage on the Throttle Position Sensor. I replaced the gray TPS with a new black one.
Upon startup the RPMS jumped to 3000 just sitting in Park. I disassembled and reinstalled figuring I had something bound in the throttle. After reassembly the idle went up to 2200, still no good! I reinstalled the original gray TPS and the RPMs, upon starting, RPMs were 1500 with the old sensor...still too high. I did reset the ECU twice during the process of putting in the new sensor and reinstalling the old sensor. Right now I found that when I disconnect the TPS electrical connector, the engine runs normal. It starts right up with the TPS totally disconnected and idles at 750 RPMs! It will not shift to 2nd gear though, when I try to drive it in Automatic Mode. I can however drive in Manual Mode and drive normal and shift right through the gears. Who needs automatic mode right?!!!
Elantra XD (2001-06) :: 2002 Gt Idling Very Rough With Rpm Jumps Back And Forth From 1500 To 2500
My wife drives a 2002 Hyundai Elantra GT. Recently the car started idling very rough with rpm jumps back and forth from 1500 to 2500 rpm. The check engine light came on and threw a code for the IAC. I also notice a clicking sound coming from the engine and I can see sparks arching at the coil/plug wire. The arching is happening at the coil with the numbers 1 & 4.
The car is difficult to drive. It shakes and surges and isn't pleasant to drive at all. These issues started happening very recently. The car ran great up until now. We've stopped driving it for the time being until we solve the problem.
We had the car serviced a few years ago and they changed the IAC and mentioned something about a gray wire that we should watch out for.
I'm not really sure what the issue is. I don't know if it is the spark plugs, wires, or coil. Or it could be the IAC or something else. I'm comfortable working on the car myself, but I would rather not try fixing many things if it is just one thing actually wrong.
So far, the only thing I've tried is to spray some carb cleaner into the throttle body towards the IAC in hopes that it would clean it and solve my problems.
Where the IAC is located. I want to try remove and clean it, but I'm unsure of exactly where it it. I know it is somewhere on the throttle body or intake manifold, but I'm not sure exactly what I'm looking for.
Santa FE SM (2001-06) :: Engine Blowing Little Blue Smoke On Startup
My santa fe 125k on it engine start to blow little blue smoke when start up ...
View 1 RepliesSanta FE SM (2001-06) :: 2004 - Engine Jumped Suddenly When Idling At About 20 Mph
I just got a used Hyundai Santa Fe (2004). I was so excited until about 50 miles of driving it. Here is what happened:
I was idling at about 20 mph when all of a sudden the engine jumped (a little bit) - the RPM went down to 0 and the check engine light came on. I pulled to the side of the road and put it in park - then the car went back to normal like nothing happened, it didnt stall all the way. I was concerned and took it back to the dealership and they did a diagnostic test on it and it came back negative, nothing was wrong with it.
My boyfriend was driving up north with it and it happened to him, this time, it stalled. He said that the engine jumps a bit- but all of the lights go on on the dash. I remember it smelling pretty hot when I opened the hood before with it happened the first time, so I asked him to open the hood. He said it did smell hot. He checked the coolant and it was empty. It looks like there is fluid in it from the outside, but that was just the line that previous fluids had. He put coolant in (not in the actual radiator, but in the place where coolant goes) and it still stalled. I didn't want him to drive it anymore for fear of something worse happening, so there it sits.
Is this something that happens with most cars, or this kind of car? I am kicking myself for not purchasing the extended warranty, but I didn't have the extra cash to add over 1k to the price. Could it be just the coolant needing to go into the radiator? Do Santa Fe's typically shut down before they overheat? I was doing some research and it seems that cars stall because of either the fuel system or electrical system.
Santa FE SM (2001-06) :: Slightly Rough Sounding Engine - White Smoke On Startup
I have an issue with a slightly rough sounding engine and some white smoke on start up. It disappears very quickly. I have been told it may be glow plugs or an idle actuator thingy, how do i check which one it is. How can you tell if a glow plug is working or not. I have a 2006 Santa Fe 2.0 with 58000 on the clock.
View 2 RepliesSanta FE SM (2001-06) :: Clutch Slipping Above 2500 Rpm
My 2001 santa fe has recently had a new clutch fitted as the old one was slipping but, when towing our caravan at the weekend the clutch is playing up again but, this time the clutch is slipping at anything above 2500 rpm yet she is pulling fine below this rpm.
View 4 RepliesSanta FE SM (2001-06) :: V6 2.7l Engine Ticking Or Tapping When Cold Started
My engine in my 2002 Santa Fe 2.7 v6 has been making a ticking sound that was especially pronounced when cold starting. It would quiet down somewhat when warmed up but still a slight ticking would be there. I thought it was the hydraulic lash adjusters. I know Hyundai's service site sates that a ticking can be heard if the factory filter is not used. I tried using the factory oil filter which did not make a difference. The car had about 85,000 miles on it and I always maintained it well as well as keeping up with oil changes. I took it to the dealer to have a repair performed related to corrosion of the rear trailing arms and had the tech check the engine noise.
It was determined that the cam chains have developed slack and were slapping on the cam chain guides which prevent the cam chains from popping off in case of slack developing which was the case here. The chain guides are made of some type of plastic material and according to the tech showed significant wear. This was all covered under the powertrain warranty. For those that are not under warranty any longer and are capable of doing their own repairs this is the list of parts that was ordered by the dealer. The parts in red are the culprits. The rest are gaskets and seals. I don't think this is an easy job.
Santa FE SM (2001-06) :: Engine Running Rough When Started / Backfire When Give It Gas
I have a problem with my 01 santa fe. When I start it the engine runs rough and when u try to give it gas it pops or backfire through throttle body and air intake tube? Checked the timing belt its ok hasnt slipped.so im stuck at this point.
View 8 RepliesSanta FE SM (2001-06) :: 2005 - Slipping / Jerking At About 2500 RPMs In 2nd And 3rd Gear
I have a 2005 Santa Fe that for the last week or so has been slipping/jerking at about 2500rpms (2nd and 3rd gear). This only happens after the car has been warmed up and running for 20 minutes or so. I have put it into manual and it does not do this, only when in auto.
View 2 RepliesSanta Fe (CM - 2007-12) :: High RPM And Idle On Startup
As the weather is getting colder I noticing again my RPM's taking longer to drop down to 1200 or less. Upon startup the engine rev's to 2000 and drops in 2 sec quickly to around 1500 (all these are based on the crude gauge readings, not a digital tach).
I don't like high RPM cold starts in the first place and why its stays just around 1500 and lower for about 2 minutes before it lowers to around 1200RPM. I don't like engaging the transmission at those high RPM's. My other vehicles did nothing like this and the increased start RPM was down 1000 within a minute.
What sensor is having the computer run it like that and not let it drop faster. I doubt its the O2 sensor since its the same on a hot day just doesn't rev up to 2k but 1500 or so. Jabs at the gas pedal doesn't work it drop any sooner either.
Santa FE SM (2001-06) :: 2004 2.4l Engine With High Idle Speed
2004 2.4l engine has high idle speed aprrox. 1000rpm.
View 2 RepliesSanta FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.
Santa FE SM (2001-06) :: Error Code U0D00 - Engine Will Rev Really High When Moving After Stop
I got an Error Code of U0D00. What this is or means. The scan tool says to refer to your manual but I don't have one.
What the vehicle is doing is that it will work fine for a while then when you stop (in park) the engine will rev really high and back down all by it self for example. It will go up to 3.5 and back to 1 rpm repeated. Then when you start moving the car it will continue to idle higher like you are pressing the gas. During all of this the check engine light will appear?
Santa FE SM (2001-06) :: Engine Running Rough At Idle / High RPM And Appears To Be Misfiring
Recently replaced plugs/wires on soon-to-be 10 year old '04 SF 3.5L (157K mi.) for the first time.
Plugs were OE Champion Platinum and all 6 looked identical except for excessive gap of .010 +/- due to all the miles. Replaced plugs with same as OE. Old plug wires looked good, but replaced them with aftermarket wires ( fit was as good as OE). Also replaced plenum gasket.
Problem is: engine runs rough at idle and high rpm and appears to be mis-firing. CEL is off and code reader shows no Trouble Codes stored.
Prius (2010-12) :: High Engine Idle Speed - 2500 RPMs
Had a first-time issue with my car today. Background, 2010 II bought in June, just short of 15K miles, never had any kind of mechanical issue.
While en route to work this morning, I was about halfway into my 15 minute drive to work, when I noticed my engine was idling very high, I would guess 2500 rpms. It started doing it while I was driving around 35 MPH, then continued doing it while I stopped at a traffic light, and continued when I continued driving to a speed around 50 MPH. The high idle while stopped was not transferred to the wheels, so it was not a safety issue as it would be in other cars.
When I got back up to 50, curious to try something, I hit the ECO mode button and the car returned to normal. I took ECO back off and the car was still fine. I had no further problems.
I would point out that this morning was about the coldest temp that the car has experienced. Outside temp ranged from 7 to 10 degrees.
Santa FE SM (2001-06) :: Code P0118 - Engine Coolant Temperature Circuit High Input
I went to my local Autozone today to have a code read and get the freeze frame data. I got a code P0118, Engine Coolant Temperature Circuit High Input. I called the dealer but they are out of stock on the sensor. Would it be a problem to use an after market sensor? I'm just concerned about the quality and accuracy of the sensor.
View 5 RepliesSanta FE SM (2001-06) :: Code P0118 - Engine Coolant Temperature Circuit High Input
Engine light is one for about a month and finally got an ODB II.
Today it reads the error code [b]P0118 which is [b]Engine Coolant Temperature Circuit High Input
The coolant sensor reads 45 C when the key is on "on" position at about 2:30 pm this afternoon and I start the engine about 2 mins the temp jumps to 68 C, are these some logical number?
Does it mean the bad temperature sensor and I need to replace it?