Chevrolet - Lumina :: 1991 - Stalls While Driving At Random Intervals Between 1 To10 Minutes - Unplugged Wire
I have a 1991 Chevy Lumina and I believe this wire is the root of my problems. I
wasn't the one who unplugged it but it seems it was unplugged as an easy way to get around a problem. When unplugged the car runs but the performance is off, It doesn't feel like it has the same power as it does when it's plugged in and it also sounds different when in idle. When the wire is plugged in the car stalls while driving at random intervals between 1 and 10 minutes and needs to be jumped to start it back up. I will attach pictures of the wire and its location within the surrounding area.
Santa FE SM (2001-06) :: E-Brake And Battery Indicator Light Came On After 10 Minutes Of Driving
I just did a brake job on my 2002 2.7l and 10 minutes after driving both the e brake and battery indicator light came on not the abs. It is not throwing any dtc codes also. Did I do something wrong or is it a coincidence meaning my alternator is crapping out? I replaced all pads and front rotors and sucked out some dirty fluid and added clean fluid. It brakes properly and I do not believe I got air in the system.
View 4 RepliesSanta FE SM (2001-06) :: 2004 - Engine Hesitation After Driving For 15 - 20 Minutes And Poor MPG
I've been having some trouble with engine hesitation after driving for 15-20 minutes and poor MPG on my 2004 Hyundai Santa Fe 2.7L. I've been slowly running through some tests as I learn how to diagnose car troubles. I just ran a voltage test on my 4 O2 sensors using a bluetooth scan tool and the Torque Pro app. I ran the tests at idle after warming up the engine. To me, the upstream sensors seem fine but downstream sensors are not behaving like they should. Aren't the downstream sensors supposed to be relatively flat around .45 volts while the upstream sensors fluctuate steadily between .1 and .9?
B1S1:
B1S2:
B2S1:
B2S2:
Touareg :: Check Engine Light / Loud Whining Sound After Driving For About 20 Minutes
@75000 miles my first check engine light. Here are my symptoms......
~After i shut the car off the fan keeps on blowing at a very high rate as if the car is over heating, its currently 45-50 degrees.
~On cold morning when i start the car up and turn the steering wheel I hear a very loud whining sound, but after driving for about 20 min and the car has warmed up the sound goes away.
Santa FE SM (2001-06) :: Codes For Check Engine Light
My '04 santa fe 3.5 v6 gls/lx, 79k miles, gas, auto, check light has just come on while I was driving a less than 10 mile journey. How can I check what is wrong. Do I need some sort of diagnostic code checker. Do any national outlets check it for free (Pep Boys or Auto Zone, etc).
Just 5 days ago (about 50 miles only) I had timing belt, water pump, plugs and leads replaced, brakes checked and lubes flushed; BUT not at above dealers. I would rather know what the code is saying before I go back to the shop who carried out the work.
Santa FE SM (2001-06) :: How To Turn Off Check Engine Light
How can i turn off check engine light (hyundai santa fe 2003 3.5) by fuse ? I do not have any code scanner.
View 10 RepliesSanta FE SM (2001-06) :: 3.5 V6 - Check Engine Light Keeps Going On And Off - O2 Sensor?
I recently purchased a 3.5 V6 Santa fe. The Check engine light keeps going on. I took it to a few shops and I am getting the same code. It is the O2 sensor in bank one. (I think the the code was po170.) The light keeps going on and off. All I can find are the same problems with different Santa Fe engines (2.7, etc. )... My SUV has 100,050 miles on it.
View 1 RepliesSanta FE SM (2001-06) :: Check Engine Light Go On And Off With P0700 And P0741 Codes
I have had a check engine light go on and off with P0700 and P0741 but since the flush day 3 it hasnt come back on and it was chucking with rpm doing small jumps... but now it does it in the mornings after sitting all night after a few chucks its fine for the rest of the day til the next day no check engine light so far, but transmission flush has worked a lot not as bad as before the flush.. So what else could be causing it? Its a 2006 hyundai santa fe with 274,000 kms.
View 24 RepliesSanta FE SM (2001-06) :: Check Engine Light On - Muffled Backfire Noise
I have A 2001 Santa Fe. The check engine light came on about 3 weeks ago and the car was still running fine up until the last few days it felt a little sluggish. Today I got a little muffled backfire noise. It was like a putting noise if I pushed on the gas to hard to speed up. The car has 95,000 miles on it.The car starts up with no problems and doesn't stall. Its A 6 cylinder All wheel drive vehicle.
View 10 RepliesSanta FE SM (2001-06) :: Check Engine Light On And Car Stalled Once - Code P0320
Check engine light on, car stalled once. Pulling code p0320 "Engine Speed Input Circuit Malfunction." Tachometer works intermittently. Where do I start?
View 2 RepliesSanta FE SM (2001-06) :: Check Engine Light Fault Code P0320
Recently got check engine light fault code p0320
2005 3.5 with 172k miles
Santa FE SM (2001-06) :: Check Engine Light Has Come On - Codes P0501 And P1529
I have a 2002 SF GLS/LX (?) with 2.7 L V6 2WD (60,000 miles) and it started to apply the ABS brakes in a random manner. Found out it was caused by a broken front wheel tone ring. So, I pulled the ABS fuse under the dash and it stopped the brake problem. Drove it today to pick up some wood and now the check engine light has come on.
My neighbor has an OBD scanner and he plugged it in and said I have a P0501 code and a P1529 code, but he didn't know what they meant. What they mean and are they related to me pulling the fuse under the dash? Did I pull the wrong fuse? Is there another fuse somewhere that I should have pulled?
Santa FE SM (2001-06) :: 2002 V6 AWD Check Engine Light Stays On After Replacing ECM
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
Elantra XD (2001-06) :: While Driving Started Lurching With Check Engine Light Coming On And Off - ABS Light Flashes
While I am driving the car it will start to die and skip. Happens randomly. Today I was driving up a small hill and it went quits on me started lurching with check engine light coming on and off. The car will turn over and start, but only for a few seconds before dying again.
Seems to happen when the car is running for a while. Also the ABS light flashes on then off randomly while driving sometimes although It hasn't been an issue. Will be checking tomorrow to see if it starts.
Santa FE SM (2001-06) :: Check Engine Light On Dashboard Came On And Stay Up After Jump Start
I jump started my santafe becouse the battery was weak. After it started the check engine light on the dashboard came on and it stays on. What could the problem be.
View 1 RepliesSanta FE SM (2001-06) :: 2004 - Check Engine Light Is On / EVAP Canister Solenoid
I have a 2004 Santa Fe 2.4L the check engine light is on and says about the evap canister solenoid. I am trying to located it but I can't find it. So, where would it be located at so I can take it apart and where is the Canister located as well...
View 1 RepliesSanta FE SM (2001-06) :: Check Engine Light Came On - Code For Throttle Position Open
My check engine light came on the other day and the code stated the the "throttle position is open" so after researching and everyone telling me that i need to change the sensor. I did everything after was fine running better but today only after 3 days replacing it i get the same problems. car has no get up and go hardly can push to 20 mph and when in idle i press the break it starts to bog down and almost want to shut off! and can be really loud...
Santa fe 05' 3.5L ....
Santa FE SM (2001-06) :: 2004 - Power Loss With A Check Engine Light On / Intermittent Misfire
I have a 2004 santa fe with a 2.7 v6. I have had a little misfire issue lately. I had a major power loss with a check engine light on it lasted for just a minute before it settled itself out. Had the code pulled at a local parts store. P0301 so I checked the plugs and they looked worn out. I pulled the upper intake and replaced the plugs and wires plus the upper intake gasket. I cleared the code and that seemed to correct the problem. Two days later, same thing happened. The engine seems to be running fine now. I wiggled the wiring harness to the injector and to the coil, no change in the way it runs. I was thinking it could be an injector or a coil pack.
View 6 RepliesSanta FE SM (2001-06) :: Transmission Started Going Into Limp Mode And Causing Check Engine Light To Come On
2002 Santa Fe, 2.7 AWD
The transmission has started going into limp mode and causing the check engine light to come on.
The codes given are p0750 and.... I think p0751, for shift solenoids C and D. There is also the generic Transmission Control Module code.
Limp mode only occurs at higher speeds although shifting feels a little rough at times in lower speeds.
If operated in manual mode the vehicle can be driven normally at all speeds without going into limp mode.
Fluid levels are fine.
With limp mode occurring in automatic but not occurring in manual mode, is it more reasonable to believe the solenoids are malfunctioning or the control module itself? I'm inclined to replace the solenoids but find it odd that the vehicle operates normally in manual. Also, can the solenoids be replaced without removing the transmission? It looks like I could get the pan off but am unsure if there is room to get the work done once it is removed.