Santa FE SM (2001-06) :: Idler Tensioner Pulley Seized
I have a 2003 Santa Fe 2.4. Couple days ago my idler tensioner pulley or whatever its called seized up and took the belt out with it. I got a pulley that resembles it from Autozone mind you that it was the only parts store that had one in stock even Hyundai didnt have the part. The only difference is the hole size for the bolt is about 1/4 inch bigger then the stock pulley. Is there any chance I can get a spacer and make up for the difference?
View 6 RepliesFord - Mountaineer :: 2002 4.6L - Engine Is Seized
2002 Mercury Mountaineer 4.6L . Ok, 140,000 miles and Engine is seized. Got truck for cheap. So, my problem is this: most salvage yards say that the ONLY engine that will fit into my truck is from an 2002 explorer 4.6L or a 2002 Mercury Mountaineer 4.6L.
Others say the mustang engine or F150 will fit. Can I have other options for a engine swap?
Santa Fe (CM - 2007-12) :: Loud Tapping Noise Coming From Engine As It Seized
I'm having an issues with my Santa Fe MY07 - Basically I was driving down the dual carriage way last week when suddenly the oil light came on and with the 500m it took me to stop a loud tapping noise was coming from the engine as it seized - The break down people came out to the car as they were inspecting it they informed me that the Sump cap was missing - the car is under warranty - however Hyundai as say that because the cannot find out why the sump cap had came off (and that in there mind they cannot give any reason why it should of) it is there for NOT a manufacturing issue and that they would not cover the repairs under warranty...
View 4 RepliesSanta FE SM (2001-06) :: 2002 Will Not Start Every Time When Put Gas In It
My 2002 Hyandai Sante Fee will not start up every time I put gas in it. The mechanics cannot find the problem. I had to change my starter two times in 6 months because I keep flooding the starter to start it up. What this might be?
View 12 RepliesAccent LC (2000-05) :: 2001 1.5L Stalled At A Stoplight And Would Not Start - Seized Motor
I've got a 2001 1.5L Accent with about 110,xxx miles on it. The car stalled at a stoplight and would not start. Earlier that day it had been driven pretty hard for a while with very little oil.
When I turn the ignition, there is only a high pitched buzzing/whirring sound. the motor won't turn over, so I assume it's probably seized up.
Santa FE SM (2001-06) :: 2002 - Hard To Start After Filling Up
Just bought a used but in pretty decent shape, 2002 Santa Fe, with 6 cylinder engine, 112K miles. I read the post about the vehicle that was hard to start after filling up - but this one is hard to start all the time - every time. Cranks fine, but once cranking, have to pump the gas pedal several times, and then it chugs just a second and then starts running. Slilght smell of gas if the hood is up, just after starting. Once running however, it runs perfectly on city and hwy. I have one mech that tells me "definitely the fuel pump" and another that tells me "definitely the purge valve" - this of course just from me describing the conditions, they have not actually seen it.
View 3 RepliesSanta FE SM (2001-06) :: 2002 Hyundai Does Not Idle At Start
When I start it up it won't idle untill you give it gas to 2500 rpms and slowly let off the pedal to 1000 rpms to keep it running and itll stay running. When you turn it off you have to redo it all over again. The plugs and wires were replaced. It started doing it couple days after the back 3 plugs and wires were replaced. Just got the fuel pressure regulator replaced and it still wont start up without giving it gas.
View 6 RepliesSanta FE SM (2001-06) :: 2002 - Dies While Driving And Won't Start Back Up?
Well i was driving the other night home and all of the sudden my 02 2.7 Awd Santa Fe dies and wont start back up. Of all places it dies on a hill around a big turn in front of a grave yard. I mean it didn't make and funny sounds or anything just died. What the problem could be. I just replaced the cam sensor last week, I have read that it could be the crankshaft sensor or even timing belt. It does have higher miles 189k.
View 3 RepliesSanta FE SM (2001-06) :: 2002 2.4 Model Cuts Out And Won't Start - No Spark
I am new here just bought a santa fe 2002 2.4 model and its playing up it will start run for a few mins then die and wont start again for a while. the crank sensor has been renewed as has the cam position sensor the fuel pump makes the normal noise so fuel is getting threw the only other symptom is when it cuts out and wont start i check both ignition coils and neither are sparking yet there is power to both, all fuses are fine .
View 21 RepliesSanta FE SM (2001-06) :: 2002 - Engine Stalling While Driving
Looking for a picture/location etc of where the crank position sensor is in the engine compartment? It seems to be a common issue where the engine stalls during driving and you pull over and are able to restart the vehicle and go on about your business.
My 02 has over 160k in miles and so am believing this part is going out according to what I've read here. My problem before was somehow the 2wire plug to the alternator worked it's way off and got that taken care of and so now while my wife is driving, it'll occasionally stall. Did a load test on the battery and it's good. Didn't check the charging system but not sure it needs to be tested.
By the way, have ran the diagnostics with the actron pocket obdII and no error codes came up and all looked good scrolling through everything.
Santa FE SM (2001-06) :: 2002 TD Engine Droning / Humming Noise?
I am struggling to find out any information regarding a droning noise coming from my engine. It generally does it when its just ticking over and disappears when accelerating.
View 4 RepliesSanta FE SM (2001-06) :: 2002 - Loud Noise From Engine When In Drive
2002 hyundai santa fe GL2 4 Cyl Automatic ... I noticed that there is a super heavy motorcycle-ish loud noise from my engine when I put it in drive. When it's idle or in reverse or neutral the problem does not occur. but then when I switch it to drive, uber loud noise...which gets louder when I step on the gas.
What has been done so far - replaced spark plugs, ignition coils and plug wires so far...also changed the oil, no fix.
No check engine light at all.....however the battery did die due to someone leaving a light on for days So I am unable to get any code readings.
Santa FE SM (2001-06) :: 2002 - Engine Running Flat Under Load
Those are the codes I'm getting. P0340, P1166 and P1167
Here's the story. Engine running flat under load. Easy acceleration is ok, but merging onto the turnpike causes a noticeable loss of power. Replaced the cam sensor, cleared the codes, ran ok for a day. Same codes came back, same flat performance.
Returned the cam sensor with another new one to make sure it wasn't a dud out of the box. Advance Auto Parts is awesome - replaced it no questions asked.
Installed the new cam sensor, cleared the codes. Ran great for a day, then the same symptoms came back, with the same codes. I'm thinking it might be the ECU? If it is, how expensive are they? And do they have to be programmed by the dealer?
This is a 2002 Santa Fe 2.7l automatic with around 147k miles on it.
Santa FE SM (2001-06) :: 2002 Turbo Diesel Engine Cuts Out Suddenly
Its a 2002 Santa Fe 2.0 turbo diesel. When driving the engine will suddenly cut out. Its as though the ignition has been turned off, there is no hesitation or warning, it just shuts down.
This is what has been done so far: New high pressure fuel pump fitted by main dealer in June. My mechanic has fitted a new high pressure fuel sensor, new low pressure fuel pump (at rear by fuel tank), changed relays around, checked all fuel injectors (found in good condition) and checked various connection plugs and wiring. At motorway speeds the engine will not cut, its only at lower speeds. When it cuts the EML comes on with a 'Fuel Pressure Fault' code. Sometimes the light doesn't come on. Sometimes the light comes on but will go out the next day. When the engine cuts out you have to wait 20 seconds before it will re-start. If you try to start before this the engine will only turn over without firing. The car has only done 79000 miles. The main dealer gave up and said they don't know where the fault is because the code is not specific enough.
Santa FE SM (2001-06) :: 2002 V6 AWD Check Engine Light Stays On After Replacing ECM
My 2002 Hyundai Santa Fe 2.7L V6 AWD failed to start a week ago. After towing to my neighborhood repair shop, it was diagnosed as a faulty ECM based on code P560 (System Voltage Problem). They replaced the ECM (along with relay) with a used one with the exact same part#. After that, the car was started and run OK but Check Engine Light stays on all the time. The codes displayed are:
P1529 TCU MIL Request Signal
P0501 VSS Range Performance
I was told that this is caused by the fact that each ECM is VIN/PIN locked. The replacing ECM was used in another car before and was locked with a different VIN thus cannot communicate with some components of the current car.
My questions are:
Can this used ECM be unlocked and relocked with a new VIN/PIN? If so, does it require the previous VIN/PIN to unlock? Most likely the previous VIN/PIN is no longer available.
Does this service require the presence of the car or can it be done with the ECM alone? Do keys need to be re-registered? The car starts fine currently.
Santa FE SM (2001-06) :: Clutch Replaced But Won't Disengage
Santa Fe 2003 petrol manual 2.4
I had a slipping clutch so decided to change it myself.
I replaced the Dual Mass Flywheel the clutch pressure plate and clutch plate.
Re assembled and the car started first time but the clutch would not disengage.
Pressed the clutch peddle down and it went to the floor until the fluid had filled then it went solid.
I pressed it down again and the clutch did not release so pressed harder and 'pop' the master clynder went - but the clutch would not disengage.
Taken the gearbox back off now and the release bearing is in sit it just would not disengage -
Santa FE SM (2001-06) :: 2003 4WD V6 2.7L Engine Won't Start
We recently changed the timing belt & serpentine belt & new alternator. Drove great for 2 days. Then car would stall out when idling, had rough idle. We replaced the Crankshaft position sensor (got one from the dealer) & the electrical connector. The engine cranks but won't start. The only code we're getting is P0335. We've checked all the fuses. Fuel pump starts when turning on the key. We've been a week without a car and trying to come up with something.
View 6 RepliesSanta FE SM (2001-06) :: 2.7 Engine Won't Start / No Fire To Coils
I just replaced the motor in a 2002 Sante Fe 2.7 due to timing belt breaking, this motor will not start, it turns over, but I am getting no fire to the coils. Crank sensor replaced waiting on the cam sensor, anything else it could be?
View 2 RepliesSanta FE SM (2001-06) :: 3.5L 4WD Not Starting / Replaced Crank Position Sensor
We bought a 2006 Hyundai Sante Fe with the 3.5L and 4 wheel drive about two months ago, it has 94,000 miles on it. It was purchased from a dealership, and they had to work on it for a month before we took it from them because of some lights that were on, resulting in some sensors being replaced. We had it about a month when we took it to the grocery store, when we came back out I started it and it made a terrible noise, but was running, I immediately turned it off. Upon further inspection, the main serpentine belt had snapped, causing some damage to the secondary belt. We towed it home and I began to fix the belts.
When I pulled off the passenger side wheel and access cover, I noticed the remains of the belt were stuck behind the harmonic balancer, I tugged on it with about 5 pounds of force, and the entire pulley fell off of the harmonic balancer. I'm not sure if the belt stacked up behind and pushed it off, or if it just went bad, but the rubber between the portion that connects to the crank and the pulley was ripped, and missing in some spots. I replaced the harmonic balancer, and both belts, good to go, everything is running fine.
About a week later, the TCS etc. lights came on, but no check engine. I researched it a bit and came up with three possibilities:
1. Fuse
2. Tone wheel cracked/broken
3. Crankshaft position sensor
I checked the fuses and nothing was burnt, I never lifted the truck up to check the tone wheels.