SC/SL/SW :: 1998 Saturn Will Not Start - Turn Over Fine But Will Not Fire
My daughter's 1998 Saturn S-series will not start. It will turn over fine but will not fire until I shoot some starter fluid down the intake. Then it fires up and runs fine. It consistently will not crank unless I shoot the starter fluid to it. I can hear the fuel pump prime up when I turn the switch on. The Saturn dealer says it may be the ECM but I have my doubts. The ECM will cost my $800 from Saturn.
View 14 RepliesPassat (B5) :: 1998 - Cylinder Won't Fire / Ignition Coil Is Not Being Activated
I have a 98 1.8T passat. The number one cylinder won't fire, according to my checks, the ignition coil is not being activated by the CPU, (no current at the connector only ground) what could cause this problem. Any way to check the crank or cam sensor.
View 2 RepliesChrysler - Concorde :: 1998 - Starts Intermittently / Crank But Will Not Fire
I have a 98 Chrysler Concord Lxi with a 3.2 L V6. In the summer time when its hot The car will get warmer than normal (I have figured out that one of the cooling fans is out and needs to be replaced). That said. after running for a few hours on the highway and if sat idle with the temperature raised, if I shut the car off 9 times out of 10 when I go to restart the car it will crank and crank but will not fire. My guess is the computer shuts the fuel off.
I have to wait about 30 minutes and it will start. Sometimes it will start very rough with a carbon smell and the need to idle it high until it smooths out. Other times It will start with out having to wait but the idle is again rough and can smell carbon. I have looked online and found some have a solution of releasing the pressure of the fuel line as it could be a symptom of vapor lock. I have tried this and no pressure is released ( I have disconnected A/C Lines on previous cars only to find a large BOOM a mess in the garage and in my shorts!) so I know I am releasing the right Scraeder valve.
Honda - Accord :: 1993 - Cranks But Won't Start / Fire From Coil But Not To The Plugs
My 93 honda accord cranks but wont start it has fuel and fire from the coil but not to the plugs, had new distbuter 1 year ago could my computer be bad...
View 9 RepliesSC/SL/SW :: 1998 Saturn SL2 No Crank - Little Smoke At The Center Back Of Engine
1998 Saturn SL2 no crank, I just turned the ignition key it cranked for 3 seconds, then stopped. then no more cranking.
Open the hood saw a little smoke at the center back of the engine. I did not determine where it was coming from. Smoke always worries me, hope the engine isn't seized up.
I also had a trouble moving the transmission selector handle back & forth between park & Neutral trying to crank the engine. My guess is starter, but would like to check easy solutions first.
Ford :: 2001 - Won't Start Cranks But Doesn't Fire
I have a 2001 mustang convertible in good cond. A 6cly that I have had very little trouble with over the past year. I put in a new battery then, just after I bought it from a dealer. The dealer had gone over it with fluids etc. and I had a friend look it over when I bought it. He said it was very clean and a good buy. So, last week I started having trouble starting it in the morning. It would crank but would not fire. I turned the key off, and then tried again, Same result, cranks but doesn't start. I turned it off again and being worried about draining the battery, I turned everything off, radio, heat and fan, lights. Then I tried to start it again and, it started. I'm thinking I need new plugs, but I ignored the problem and went to work.
A couple days later I was leaving the grocery store, turned the key and same thing again, cranks but doesn't fire. I knew what to do. Turned off everything and tried it again, it started. Ok, so now some repair, possible plugs, is on my priority list. I need to get this fixed before the bad winter weather comes. Yesterday, after a long day at work, I was ready to go home and I it happened again. This time it's terminal. No matter what I did I couldn't get it to fire. This morning it's sitting in the office parking lot and I need to deal with this today.
Could be plugs, could be the fuel pump. Before I call the dealer and pay 4x what I should for this, what do you think it could be? 3.8 6cly. The car is sitting on a slight incline, in the parking lot. Gravity pulls fuel from the engine to the gas tank, if a fuel pump is going bad this could be why I can't get it to start. I'm going to roll it to a level area and hit it with starting fluid to determine if the pump is bad. I'll also pull a couple plugs.
Volvo :: 2003 XC90 Cranks / Wants To Fire But Doesn't Start
I have a 03 xc90 t6 came out of work the other day and it wouldn't start replaced spark plugs, both cam sensors, crank sensor. After doing all that it sounds like it wants to fire now but doesnt.
View 1 RepliesF Series :: 1989 460 - Crank / Fire But No Start
F-250, 1989, 460. Until the truck set through 2 weeks of 90+ weather it started just fine. This morning it would not start. Plenty of cranking power, seems to fire then nothing. I can keep on cranking. I am not a mechanic and will have to get a tow to a shop.
View 1 RepliesDurango :: 2000 / 5.7L Runs Fine But Doesn't Want To Start Again - Cranks But Does Not Fire Up
I have a problem with my Durango whenever i drive my car it is fine and normal. When i get to where I am at and i try to start my car again it will just turn over like it wants to start but doesnt. I just recently started driving the car for about 4 days ago and it drove fine. Until yesterday i got to my shop and tried to start it.. it will just crank. I scanned it and it turned out i had a bad crankshaft sensor. I gone ahead and replace that and the car starts up fine. I drove it around town and then this morning drove it to work and when i tried to leave for lunch it did the same thing. It cranks but does not fire up. I scanned it.. and no codes. My dad was saying something like sometimes it has sparks going to the crank and sometimes it doesn't.
View 2 RepliesFord - Ranger :: 2003 Will Not Start / It Cranks Just Fine But Doesn't Fire
I have a 2003 Ford Ranger 4X4 4L AUTO. About once every 6 months it will not start. It cranks just fine but doesn't fire. After about 45 min. it start and runs great for an other 6 Months. I have replace the plugs, wires, distributor cap but it hasn't solved the problem. It has had this problem when it is cold and warmed up.
View 4 RepliesFord Wiring/Electrical :: Crank But No Start / Not Getting Spark From Coil
1996 Ford F150 5.0 ... New battery, new alternator, new starter, new coil, dis cap good and rotor is good. New plugs and wires. Ignition mod tested good.
Drove a mile from my house and lost power to my engine. Lights and radio work. Just sits there and cranks and cranks. I'm not getting spark from the coil. Don't know a lot about engines.
Accent LC (2000-05) :: 2001 GS Won't Start / Engine Cranks Fine But Doesn't Fire
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
Pontiac - Grandam :: 2003 - No Cold Start / Crank But Never Fire
I have a 2003 Pontiac Grand Am, 3.4L V6. The engine runs perfectly as long as it is kept hot. If allowed to cool completely it will crank and crank all day but never fire. However, if I disconnect the battery for at least 30 minutes and reconnect it, it fires right up every time. I have good fuel pressure when it will not fire, but it seems as if the injectors will not fire. Suspecting the injection driver, I replaced the ECM/PCM. The exact same problem still exists.
View 8 RepliesFord F-150 - 1997-2003 :: Remote Start Will Crank The Engine Over But Not Fire
I just picked up an 02 Supercrew. It came with a “Ford” remote starter. I imagine it was a dealer install for the previous owner. Anyways when I try to use the remote starter, it will crank the engine over but not fire. If I manually start the truck it fires up immediately. How come the remote start wont fire?
View 7 RepliesFord 7.3L Power Stroke (1999-2003) :: Won't Start / Just Crank And Tried To Fire
Friend's 2000 7.3 wont start, just crank and crank tried to fire but nothing in the cold leave it plugged in and it starts leave it in a shop over night and it starts with a shot of either, he is a truck driver and the truck will sometimes sits for 6 weeks at a time this time 2 weeks before I touched it. He wanted me to install a fuel pump so I did and started the following:
Cracked fuel lines to see if I had fuel psi at both heads
I tested glowplugs they all read at 0.3 on all 8
I have power to harness as the same at both sides of the relay
RPM tach jumps
Oil psi gauge rises
Using my phone I can read hpop and 2000 at cranking (how accurate that is im not 100% sure)
All fuses good
Toyota - Camry :: 2002 - Hard To Start / Starter Would Crank Just Fine But Engine Would Not Fire
Camry 2002 LE (4 cyl Auto), 140K mi
This morning, for the first time I can recall, the car would not start right away. Had been sitting in the garage for 2+ days. Starter would crank just fine, but engine would not fire. No lites were left on overnite. Finally (after about 6+ attempts), engine started -- runs fine now.
Took it to TOY dealer. Their diagnosis: weak battery, alternator low output.Happy, had recently (6 mos) replaced battery after 4 years of use, so got a new battery N/C.TOY ran a charging system check and it shows "Alternator Condition: OK" (midway between shitty and great I recall).
Funny, but my first thought when it would not start was the fuel system (fuel pump) or dirty ignitors. I did ask my regular mechanic for an opinion, and he thinks it might indeed be the fuel pump -- perhaps a clogged filter.
Ford F-150 - 1997-2003 :: 1998 4.6L - After Rebuild Turns Over But No Start - No Fire?
1998 F150 with 4.6L Windsor SOHC. I just completely rebuilt the engine including pistons, rings, timing chains (timing is good; compression @ 180 psi), 2 new coils, wires, plugs etc. and there's no fire at the plugs when I crank it. It turns over good but doesn't start. The fuel pump comes on and there's fuel up to the injectors. Before I disassembled the engine, it still ran good except for one piston. The 2 new coils, wires, plugs were replace before I rebuilt it. I was very thorough when re-installing the electrical etc... and triple checked it all after the engine not firing. Fuses are good. I know it's hard to trouble shoot without seeing the truck? The battery has been disconnected for months as I started a long time ago. Computer maybe?
View 6 RepliesFord F-150 - 1997-2003 :: Crank But Not Fire Or Start / Read Codes By Malfunction Indicator Lamp
Have a 2000 F-150, 5.4L. Once recently in a parking lot, it would crank but not fire or start. Wife called me to come get her. By the time I got there, she said it started "after she loosened the gas cap & re-closed it." But, it started fine for next several weeks. Yesterday it didn't. I read a bunch of threads here on possibilities. Many troubleshoot items I checked out or had done.
Chilton manual says you can get limited error codes from the light on dash flashing - MIL - Malfunction Indicator Lamp Method.
For now, I'm trying to find the 2nd, separate, one-wire lead "near or with the (main) Diagnostic Connector." They call the single wire / connector the "Self-Test Input connector" (STI). You're supposed to use a jumper between that STI & the upper, right connector of the main diagnostic connector. Then you (may) get flashes corresponding to codes via the key on, engine off method.
I see no such single wire lead or connector anywhere near there. Not up under the dash either - stuck my head under there & used mirror. There's a separate connector (not in use) clipped on the L side of the main diagnostic connector, but it has 5 pins inside. I took pics, but forum says I "may not post attachments." Been a member for yrs. That extra 5 pin connector faces toward firewall.
There's an "empty hole" - 1/4 in. (facing forward) in the bracket that holds the main diagnostic connector. Just above the main connector. Not sure if something was ever there
If no one knows how / if the Malfunction Indicator Lamp Method works or where the jumper goes, I'll be forced to buy a code reader w/o researching which are decent or crap (around $200 or less). I maybe? could wait to order one online (if knew which one). Also have AutoZone, O'Reilly, Advance, NAPA, PepBoys & others locally.
* The truck shows a check engine soon light, so should be a code already. * Yes, I tried her loosen / tighten gas cap trick.
* Also put a slow charger on for a while & even used the fast start setting on charger. No go, but engine turns really fast.
* Crawled under the gas tank & listened for fuel pump to activate when key is turned to Run.
* Fuel pump made a small noise - more like a relay or "clicking" - not a whine or whir.
* Checked most fuses - under dash & hi voltage box - that have anything to do w/ fuel pump, PCM & several others - mentioned in similar threads here.
Can't really check relays & don't want to just start replacing parts. I don't have a code reader & reluctant to buy one from local store w/o some reasonable research. (I don't mind buying one, but...). If I could drive it to the auto store, I wouldn't be asking this. Chilton's doesn't say if this malfunction indicator lamp method will work if a vehicle won't start. But, a code is already thrown.
Saturn - Sl :: 2000 - Intermittent Start Up / Ignition Doesn't Complete Engagement
My Saturn 2000 LS1 has an intermittent start up problem. If the ignition doesn't complete engagement, the engine shuts down. After a 12=15 minute wait, I try to start again and it engages and starts. (I think the computer has to be re-set, thus the delay)
Nothing shows up on code except "security" but no fix.
I noticed using the remote caused this problem more often. So no longer use it. Also, got a new ignition key which worked. We think it has something to do with "security" as the light comes on....intermittently. Is there a replacement part for the "security" system? Checking your site, no one else seems to have had this problem.