Accent LC (2000-05) :: 2001 GS Won't Start / Engine Cranks Fine But Doesn't Fire
My 2001 Accent GS (1.6L DOHC) wouldn't restart after a short 2 mile trip to a local store. The engine cranks fine but doesn't fire.
It has had a CEL issue for awhile and after it wouldn't start I checked the codes and got:
303
335
722
I replaced the Crank Position Sensor and Fuel Filter but it still just turns over.
I hear the fuel pump run when I turn the key on and I broke the fuel line and it is Pressurized, so I doubt it is a fuel issue.
The 722 code indicates the output speed sensor has an issue. Need to know definitively if that sensor is completely shot could this prevent the ECU from firing the engine?
I have had this car since it was brand new and I'd like to keep it going a little longer.
Ford - Ranger :: 2003 Will Not Start / It Cranks Just Fine But Doesn't Fire
I have a 2003 Ford Ranger 4X4 4L AUTO. About once every 6 months it will not start. It cranks just fine but doesn't fire. After about 45 min. it start and runs great for an other 6 Months. I have replace the plugs, wires, distributor cap but it hasn't solved the problem. It has had this problem when it is cold and warmed up.
View 4 RepliesVolvo :: 2003 XC90 Cranks / Wants To Fire But Doesn't Start
I have a 03 xc90 t6 came out of work the other day and it wouldn't start replaced spark plugs, both cam sensors, crank sensor. After doing all that it sounds like it wants to fire now but doesnt.
View 1 RepliesDurango :: 2000 / 5.7L Runs Fine But Doesn't Want To Start Again - Cranks But Does Not Fire Up
I have a problem with my Durango whenever i drive my car it is fine and normal. When i get to where I am at and i try to start my car again it will just turn over like it wants to start but doesnt. I just recently started driving the car for about 4 days ago and it drove fine. Until yesterday i got to my shop and tried to start it.. it will just crank. I scanned it and it turned out i had a bad crankshaft sensor. I gone ahead and replace that and the car starts up fine. I drove it around town and then this morning drove it to work and when i tried to leave for lunch it did the same thing. It cranks but does not fire up. I scanned it.. and no codes. My dad was saying something like sometimes it has sparks going to the crank and sometimes it doesn't.
View 2 RepliesSebring - Chrysler :: 1996 - Cranks But Doesn't Fire
96 sebring 2.5l v6 non-convertibleRan terribly for 12 blocks when I bought it, then died and wouldn't start.Bought it because friend said that mechanic had told him it just needed the head gasket changedReplaced the head gasket then it would crank but not start
checked, getting spark and compression on all 6 cylindersreplaced:-ecm-crank position sensor-combination distributor/camshaft position sensor/coil-flushed fuel system and replaced gas. checked everywhere for possibly misconnected wires and possible misconnected vacuum tubes, they are all triple checked ok. Checked the timing about a dozen times. Checked for misaligned timing sprockets, all ok, no sheared keyways, valves open and close at appropriate times / correct order and crankshaft timing mark matches cyl 1 position.
Fuel pressure is great.Turns over but doesn't fire at all.
Accent LC (2000-05) :: Car Cranks Strong But Doesn't Fire
About a month ago my 2002 accent started intermittently turning on. The car cranks nice and strong when it doesn't start-(until the battery loses too much power from repeated cranking). When it does start, it happens instantaneous, no issues no hard start.
I have talked to multiple people with varying amounts of automotive experience, who have given many things to try.
Things I've replaced or tested, hoping they were an issue:
-Starter and relay
-Fuel pump and filter, as well as relay for pump.
-Battery, post connectors and wires to starter
-Alternator and belt
-Multimeter tested fuel injectors and ran fuel system cleaner for last 3 fill ups
-Replaced spark plugs and wires
-Ran fuel line antifreeze every 2 tanks or so
Things I've been told might contribute to the intermittent starting, but haven't looked into
-Inconsistent fuel pressure
-water in the fuel tank
-Bad ignition switch
-MAF sensor
I live in area, currently in the icy grip of winter. I thought the cold would be a huge contributing factor, but alas, when the car has fired up the temperature has ranged from 1 to -32 degrees and has no issues starting in the deep cold.
Oldsmobile - Bravada :: Cranks Good / Can Hear The Fuel Pump But It Doesn't Fire Up
Sometimes my Bravada won't start. It cranks good (new battery) and I can hear the fuel pump , but it doesn't fire up. I just got it back from the repair shop.?
View 4 RepliesElantra XD (2001-06) :: 2002 GLS Cranks But Doesn't Start (sometimes)
My 2002 Elantra GLS seems to have some sort of heat related problem.
I live in Arizona, where temperatures routinely reach well over 100. In the morning my car will start fine, after driving it for some time and parking somewhere, if I try and start the car within a couple hours of driving it, it will crank but not start. Lifting the hood to cool it seems to expedite this to get it started.
I had a mechanic friend of mine hook up his OBD computer at his shop, nothing out of the ordinary. He suspected either a crankshaft or camshaft position sensor. No check engine light, nothing out of the ordinary on his computer check. I removed spark plug wires for cylinders 1 and 4 and I have spark while cranking when it fails to start. My mechanic friend said the spark would rule out a faulty crankshaft position sensor. I have also tried spraying starting fluid into the intake manifold, and it has no effect. The battery has been replaced within the last two months, connectors are new as well.
Ford Super Duty (1999-2016) :: 7.3L Suddenly Start Taking More Cranks To Finally Fire Up On First Start
I don't drive the truck much anymore but over time my MPG has gone to total crap...about 10mpg around town...and that's baby-ing it.
Now it suddenly takes many cranks to finally start on a first start. (cold or warm days)....
Ford F-150 - 1997-2003 :: 2000 Truck Cranks But Won't Start - No Fire
2000 ford f150 4.6 auto. Will spin over but won't start. checked coil for fire, no fire. Check fuel rail for fuel, no fuel. No theft light flashing and no check engine light on. Has new battery and plenty of fuel in tank. Started fine yesterday but not today.
View 5 RepliesElantra XD (2001-06) :: GLS Cranks But Won't Fire
The car died randomly and now it won't fire. I know it is getting fuel, none of the relays or fuses are bad. I am pretty sure it is not getting spark. The spark plugs that were in it were pretty much gone, put some brand new ones in and while testing I didn't see it spark. The wire resistance tested fine with my multimeter. I just checked the resistance on the coil pack. High side (set to 200k ohms) was ~15.6 on either bank, low side was 0.060-0.062 (set to 2k ohms, my meter doesn't go lower).
View 2 RepliesFord F-150 - 1997-2003 :: Hard To Start In Cold / Cranks Fine But Does Not Want To Fire
My girlfriend has a 2003 f150 4.6lt pick up its a great truck most of the time. Problem is when the temp gets in the neg double digits it becomes very hard to start it cranks fine but doesnt want to fire. When it does fire it might stall a few times before it stays running. The last cold snap we had I replaced the battery and in the summer the starter got changed. I have heard that this model of truck are known for hard cold starts. I am just wondering if this is true and any other thing besides block heater. It is strange that my 89 gm pickup will start no matter what temp and I'm having problems with the newer truck.
View 1 RepliesFord 6.0L Power Stroke Diesel :: 2005 E350 - No Hot Start / Just Cranks But Won't Fire Up
I have a 6 liter 2005 e350 diesel that starts great when cold and runs well all the time but after it warms up it just cranks but won't fire up. But if i shoot ether into the intake it will start. It doesn't show any failure codes.
View 2 RepliesGolf IV / Jetta IV :: 2001 VR6 GLX Cranks But Will Not Fire
To start I was driving home the other night, car just stalled out and would not start back up, at all. Just cranks over and over. Things I have checked
- I am getting a spark from the plugs
- Fuel pump primes when key is turned on
- Fuel comes out of lines, even more so when key is switched over so pressure should be ok, I have not checked exact pressure due to not having a gauge.
- I have checked all relays under the steering wheel (just visual) some had brownish on the connectors and I cleaned all that off.
- All fuses are good and not blown (voltage meter also showed power coming to a few key fuses I checked.
I am down to a few things that I have read could be possible causes
- Camshaft Position Sensor
- Crankshaft Position Sensor
- Not sure what else to really check
Ford 7.3L Power Stroke (1999-2003) :: F250 Cranks Fast And Fine But Won't Fire Up And Start
My dad has a 99 F250 with a no start issue. Everything was starting and running fine one day. The next he gets a no start. Cranks fast and fine but wont fire up and start. He has a scangaugeII hooked up to it and his oil pressures and volts look fine. His tach moves when he is trying to start it. He checked the icp sensor and it had oil through it so he replaced it with a Ford part. Unplugged it and the scangauge pressure goes up but no start. He also replaced the ipr with a new Ford one just in case. He checked and is getting low pressure and high pressure oil.
I am having him check the fuel heater fuse #22 to make sure it is not blown. He had the block heater plugged in all night along with a battery charger to make sure they are topped off as well. We have gone through a couple of the checklists on this site for a no start condition but nothing has solved it yet. I think he is sitting at about 200k on the motor. No major issues or problems until now. He is currently also pulling the ICM to check it out as well. No codes are being thrown.
Santa FE SM (2001-06) :: No Power When Pulled Into Gas Station / Cranks But No Fire
Here is what happened. Pulled into gas station and car just died. Tried to restart and no fire. Cranks but no fire. Flat bed trip home and started to diagnose. Thought it was a bad fuel pump so I pulled and tested with a direct power and functions fine. Checked all fuses and relays, all seemed fine. checked for power at pump and nothing. Reset cut off switch and still nothing. Thought maybe ECM relay in the under hood fuse box was bad I borrowed the one out of a friends car. Nothing. Thinking ECM was bad put theirs in my car and got power to pump. So I put their car back together thinking mine was the ECM, then theirs won't start. The ECM relay i took from there car and put in mine blew when i tried to start my car. Got another ECM for my car and put in. Still no power at the pump. Here is the info about the car. 2001 Santa fe 2.4L auto. 80,000 miles. Timing belt, tensioner and all Idler wheels changed along with water pump at 71,000 miles. This car has been very reliable up till this point. No check engine light came on at any time..
View 8 RepliesCelica :: 94 GT ST204 - Cranks / No Start And Not Even Fire Up At All - Code 12
I have a stock 1994 Celica GT with the 5sfe M/T .... I do have a headgasket leaking, and I am having another motor rebuilt and put in next month. I just need to nurse this one along for now. Right now it cranks but will not start. does not even fire up at all.
Code 12 - so I got another dizzy from the salvage yard, the pickup coils ohm out like they should as does the ignition coil. and I bought a brand new condenser for it as the old one tested bad. and when I first got the dizzy i put it in and it fired right up and ran for a couple days, then began doing it again. I went back to the salvage yard and grabbed another one that tested good, and when I put it in it fired up the first time but then shut off and has not started since.
But is it possible for the distributor to still be the problem even though the coils test ok? the shaft doesn't have any play in it, and the air gaps are within spec. I can barely get a .2mm between them. I also grabbed a couple of igniters while I was there. When I get it to run it may die when its cold and give me a code 14.
So from there I'm down to testing the distributor circuit, and the starter signal circuit, and the ECU. What is the best way to go about testing this to be Certain of what I need to go buy instead of just replacing stuff.
Suburban :: 87 Start Intermittent / Cranks But No Fire Not Even A Sputter
I have been checking on the automotive forums for Suburban no start problems and have tried some of the solutions, but my vehicle still doesn't start. Here is where I'm at: I have spark, fuel pressure at the throttle body, the fuel pump in the tank is working, new cap, rotor, coil, module, fuel filter, and ECM.
I just ran the truck 2 days ago for 10 minutes to flush the radiator, turned it off to install a new t/stat, then it wouldn't start again. I have tried starting fluid, gasoline, it cranks but no fire, not even a sputter. The pump has been replaced probably 9 years ago. The only other thing not replaced is the pickup coil in the distributor, although the distributor was rebuilt about 10 to 12 years ago. This vehicle just sits until needed, can't afford to drive it daily. The truck is a 1987 Suburban 1/2 ton 350K engine, automatic, 4wd.
Accord :: Cranks But No Fire - 30 Sec Delay Required To Start Car And D4 Flashing
My 95 Honda accord 4 cy. vtech, will turn over but not will start, you can try unlimited times and it just cranks, but no fire or start.... UNLESS I wait about 30 seconds first. In this time what happens is, for 15 seconds the usual dash lights are on, including check engine light, at 16 seconds the D4 green transmission light starts to flash rapidly. At 30 seconds the main relay can be heard to finally click in, and the fuel pump whirs and primes the fuel system for 1.5 seconds and immediately the check engine light turns off, the D4 light turns off, and the fuel pump also stops whirring. AT this point, at any time from here on out, (until you turn the car off again) you can turn the key the rest of the way to start, and the engine cranks over and now immediately starts right up!
Sometimes all the above happens just as described, but the D4 transmission position light does not start to flash. Everything else happens the same way and timing and after 30 seconds the car will start. NOTES: a. The obd trouble codes do not flash any codes when the jumper is put in place to read the codes. b. I have removed and checked the main relay, looked ok, and just in case I re-soldered all connections on the main relay board. c.the car drives and shifts fine. d. The time frames are exactly the same every time. Electronically perfectly the same, like the computer finally decides, OK go ahead and work now. Or like the car is attempting by some programmed response to say that something is wrong and needs attention.