Camry 2012+ :: Shifting From Reverse To Drive
Whats the right way to shift the car, when I reverse the car and want to change it drive D, should car be at complete stop OR we can still change it from R to P with with car slowly moving back. I usually apply brake, and let it complete stop, then change the gear shifter. But yesterday I was in hurry and didn't wait for the stop, car was very slow, but I didn't notice any jerks or anything wrong with it.
View 5 RepliesCamry 2012+ :: Vibration At Idle Only When In Reverse Or Drive
A coworker has asked me to take a look at their 2013 Camry LE, 48,000 miles. It has a quite annoying vibration at idle and only when in reverse or drive. AC is not running this time of year, but does get worse if the compressor is turned on.
I'd like to think the trans and engine mounts are fine. It does not have any noticeable torque converter shudder. I have cleaned the throttle body, not that dirty, but not much improvement.
I suggested that he try different brands and grades of gas to see if matters improved at all - Shell 89 seems to be a slight improvement over what is normally used (just 87 from Costco, Sunoco, or Hess), but nothing substantial.
Spark plug change, decarbonizing top end?
Spark plugs look about like I'd expect an iridium plug to at these miles - no signs of oil burning, not tons of carbon, etc. I didn't get a real good look at the piston tops.
Passat (B7) :: 2012 SE Jumps When Shifting To Drive Or Reverse
I have a 2012 Passat SE (5cyl) automatic with 25k miles on it. I have noticed that when i put my car into gear (reverse or drive) that my car jumps with a little burst of speed (while I am easing off the brake), I don't have the slightest clue of what it could be, or if that's normal or not as i purchased the car less than 3 weeks ago.
View 3 RepliesElantra MD (2010-15) :: 2012 GLS - Loud Clicking Noise When Going From Reverse To Drive
I just started hearing a loud click when I change from park to reverse and from reverse to drive. If I keep moving the knob between those three spots with my foot on the brake and hand brake off, I hear a loud click at each spot. Hard to describe... anyway, this only happens when I first start the car, by the time I get to work if I try doing that when I park there is no loud click sound. The thing is, I don't know if this was always happening and I just noticed it now, or if it just started.
View 14 RepliesElantra MD (2010-15) :: 2012 GL Jerking Whenever Switch The Gear From Park To Drive Or Reverse / Neutral
I have an Elantra 2012 sedan GL and last year i tried installing HID's. It worked for a whole but then it stopped after. I learned that it wasn't getting enough power so then yesterday I bought a wiring kit to be able to wire my HID to tap to the battery to get more power. Everything was fine till I got to work but when I had to leave work., there was an issue. Whenever i switch the gear from park to drive or reverse or neutral. My car seems to jerk. And when I'm driving and it changes gears, it also jerks. Kind of the same thing how if your driving a manual car and you change gears wrong. This happens when my lights are off. But when i turn them on it then stops. And when i turn it back of it doesn't do it anymore.
View 5 RepliesElantra MD (2010-15) :: 2012 - Tap Clunk Type Noise When Shift The Auto Trans Into Drive And Reverse
For a few months now I have been hearing a tap clunk type noise coming from under the car when I shift the auto trans into drive and reverse. Also sometimes when the car is slowing when driving I hear the tap sound as it shifts into first. I drove in by my local dealer and they listened to it and said Elantra transmissions can get noisy there is nothing wrong. They told me I have plenty of Warranty left so if something happens I will be covered.
View 2 RepliesPassat - Volkswagen :: 1998 - Engine Began Intermittently Shuddering / Steering Wheel Vibrate?
I have a 1998 Passat turbo wagon. A couple of months ago, the engine began intermittently shuddering/stuttering. The car/steering wheel vibrate when accelerated. Acceleration is very slow. It may start when started, or just driving down the road. This can last a few minutes/block or several minutes/blocks. It disappears just as quickly as it begins. My garage ran engine analysis and nothing shows. Can't do anything till they can duplicate, and I can't cause it to happen. During the occurrence, tach is at 9000 and steady. I use high octane gas. Today, while stuttering the engine just quit twice while stopped. Car has 115,000 miles and otherwise is in excellent shape mechanically (regular oil changes, etc.). What's happening?
View 13 RepliesFord Super Duty (1999-2016) :: 2002 F250 4X4 - Front End Shaking And Brakes Began To Intermittently Hum When Stopping
Problem started with the front end shaking a little bit when braking like the rotors needed turning. Then the brakes began to intermittently hum when stopping. Then my ABS light came on. Put the truck up on the stands and disassembled the brakes on both sides. The ABS sensor was chewed up on the driver side. The less than year old hub felt sloppy so I changed it. Put everything back together.
New hub came with new ABS sensor. Went for a test drive ABS light is gone and I no longer shake or experience the hum when applying the brakes. However now when I go to stop right before I come to a complete stop the driver side (new hub/spindle side) I hear what sounds like the grade school class clown making a fart sound with his mouth, and the truck pulls to the driver side. Is the ABS system malfunctioning or is this a caliper issue? Calipers look like they are OEM.
Prius (Gen 3) :: Shift To Reverse But Car Went To Drive Instead?
I shifted to "reverse" but the car went to "drive" instead. I've only had my Prius for 2 weeks. Today was the first time I encountered this problem, and it happened 3x.
View 14 RepliesPrius (2004-09) :: Cannot Get To Shift Into Reverse Or Drive
Ok first off I am a used car dealer and have sold 20 plus gen IIs and never had to replace the main Hybrid battery pack... until this one! after i replaced it with a used one every thing seemed to be fine, I drove the car for a while the check engine light went off(the reason we knew the battery pack was bad) and after a few miles of driving the red triangle light went off.. yea! I think im done so we put all the carpet and rear seats back in and i get in it to start it and put it on the lot and it will not go into gear or start. all the dash lights come on and will go into neutral when i push the brake but just will not go into drive or neutral.
Here are some things we already tried:
1. put the original battery back in the car- no change
2. put our jump box to the small battery-no change
3. checked the brake lights they are coming on when i push the brake
4. put the scanner on the obdII- no codes
The car is an 06 with 200k miles in very good shape. Could it be in the shifter and not related to the battery change out?
Prius (2004-09) :: Starts But Won't Go Into Drive Or Reverse
I have a 2005 Prius. 3 weeks ago my dash lit up with warning lights so I took it to the dealer. They ran a diag and came up with
P3000/123
P0A80/C2311
"Vehicle has bad #4 battery block. Neesd HV Battery pack and HV ECU" I had just hit 150,900 miles.
Given the cost I decided to fix it myself. After tracking down some cells and getting a HV ECU from a local junk yard I pulled out the hv battery broke it down, tested the two cells in the #4 block and replaced the low voltage cell. I then replaced the HV ECU. I put everything back together and everything started up fine and ran great.
Things work well for 2 weeks then yesterday as I'm pulling into my driveway the main error indicator (the big red triangle containing a !) lit up. Needless to say I was disappointing. I turned the car off and then turned it back on. At this point most all of the error indicators were lit (see attached image). I get a new error indicator on the multi-information display (the red car with the ! in it, according to the manual I'l supposed to take it the the dealer immediately) The car started but the engine does not start. The car will not go into drive or reverse, just neutral.
I thought I may not be pressing the brake correctly so I spent some time making sure I was depressing the brake pedal fully when starting up. No change. I checked that the break lights are working when I press the pedal and they are working correctly. I checked the brake fluid reservoir and it is filled to the correct levels.
A friend bought a innova OBD2 scan tool (his kid's cars break a lot) I borrowed it and hooked it up to my car. No error codes detected was what it told me. I was a bit perplexed. I switched to the Toyota enhanced DTC and then Readiness DTC and finally found some codes:
P0300
P0171
P0172
P000A
I found what looks to be the 2004 service manual online in an open directory : [URL] ...... While I don't find P000A I do see the other 3.
P0300 (05–157)
Random/Multiple Cylinder Misfire Detected
Open or short in engine wire harness
Connector connection
Vacuum hose connection
Ignition system
Injector
Fuel pressure
Mass air flow meter
Engine coolant temperature sensor
Compression pressure
Valve clearance
Valve timing
PCV hose connection
PCV hose
ECM
P0171 (05–143)
System Too Lean (Bank 1)
Air induction system
Injector has blockage
Mass air flow meter
Engine coolant temperature sensor
Fuel pressure
Gas leakage in exhaust system
Open or short in A/F sensor (bank 1 sensor 1) circuit
A/F sensor (bank 1 sensor 1)
A/F sensor heater (bank 1 sensor 1)
EFI M relay (integration relay)
PCV valve and hose
PCV hose connection
ECM
P0172 (05–143)
System Too Rich (Bank 1)
Injector has leakage or blockage
Mass air flow meter
Engine coolant temperature sensor
Ignition system
Fuel pressure
Gas leakage in exhaust system
Open or short in A/F sensor (bank 1 sensor 1) circuit
A/F sensor (bank 1 sensor 1)
A/F sensor heater (bank 1 sensor 1)
EFI M relay (integration relay)
ECM
I was hoping for something a bit less vague. So that's where I am right now. I have the indicator lights as seen in the attached image. The car powers up but the engine does not start. The car will not go into drive or reverse. I don't know the difference between the standard DTC and the readiness DTC.
Prius (2010-12) :: Way To Reverse The Drive Knob?
Is there any way to reverse the drive knob so that forward is drive and backward is reverse? For some reason I tend to put it in reverse and expect to go forward. Any options?
View 1 RepliesPrius (Gen 2) :: 2006 Will Shift Into Neutral But Not Drive Or Reverse
Vehicle was repaired after front end collision and I get no codes found on scanner, had some bad connectors which I replaced and codes went away. I don't get ready light and the dash lights do not cycle off (ABS, SRS, Check engine, Etc. Etc.) The car will shift into neutral but not drive or reverse. Has new Aux battery and Hybrid battery is showing two bars. What to check ?
View 6 RepliesPrius V :: Stuck On Neutral When Try To Shift The Car Into Reverse Or Drive
I have recently been having problems with my 2013 Prius v (lowercase v for the Prius v wagon). When I press power, all the dashboard lights turn on. And when I try to shift the car into reverse or drive the car stays on neutral. What is going on?
View 7 RepliesPrius (2010-12) :: Gear Not Engaging In Drive Or Reverse
2010 Prius 52K miles... Not engaging in Drive or Reverse, Engine is not starting either. Got Message - Put in park , All the lights are ON , in the Dash .
View 11 RepliesCamry 2012+ :: The Engine Began Spurring For A Couple Seconds
It was pretty warm this afternoon, had the AC on full blast. Drove into a left turn lane and stopped for the red arrow, the engine began spurring for a couple seconds. Then it caught itself but afterward felt the whole car shake for like a minute, drove off once it was a green arrow and nothing else happened. Has any one else had this or a similar experience happened to them? My Camry just hit 30k miles, I wonder if it just had a "spaz" (or whatever you want to call it) attack.
View 4 RepliesPrius (2004-09) :: Won't Go Into Drive / Reverse - Big Red Triangle And Other Warning Lights
I have a 2005 Prius with 107K miles which I had taken off the road for about 2 months. Car ran fine previously. I just replaced the old 12v Battery with a new Optima replacement battery, changed the oil and filter, and have 1/3 tank of gas. Inserted the key into the slot, foot on brake, pressed the Power button, and, just about every warning indicator light is On (Brake, Red Triangle, Check Engine, (!), ABS, VSC, Traction Control) and the yellow exclamation mark with "Problem" message appears for a second on the Display, then a Red Car (!) appears in the upper left-hand corner of the display. Car will Not go into Drive or Reverse, and engine will not run, even when gas pedal depressed. Am I doing something wrong, or did I let the car sit too long?
View 11 RepliesCamry 2012+ :: Seatbelt Light Came On And Began To Chime When Driving At 45 - 50mph
2012 Camry SE I4, non-entune, no roof, Kentucky built in spring '12.
Tonight on the way home, driving in light traffic, roughly 45-50mph seatbelt light came on and began to chime. I was wearing my seatbelt at the time, and had nothing in the passenger seat. When approaching a stoplight, the light went out and the chime stopped upon braking. I am going to take it in tomorrow to have it checked, but am assuming the dealer will find nothing. I looked under the dr. seat and there wasn't anything that could have pulled on the wiring.
So again, briefly:
During light traffic with seat belt buckled properly, seat belt light illuminates and chime starts. Upon braking for stop light the seatbelt light went out and chime stopped.
This is kind of a big deal to me because this is my wife's primary vehicle and the airbag will not work with the seatbelt light illuminated.
Prius (Gen 2) :: 2006 Car Went Into Limp Mode - Unable To Shift Into Drive Or Reverse
I was once the proud owner of a 2006 Prius with 106,716 miles on it. Never missed a regularly scheduled service. Now, I am no longer proud, but just another owner of a Prius with a failed transaxle.
Last week, I parked my car on my way to work and, while the car was idling in park, the Triangle of Death (red with exlamation mark within) came up on the dashboard. The car went into limp mode -- it was unable to shift into drive or reverse -- so I had it towed to Darcars in Silver Spring, MD. They thought the original 12v battery was dead, so they replaced it.
P0AA6 -- 526 and 613 codes 600 miles after Transaxle Fluid Replacement...