Prius (2004-09) :: CEL On / Misfire On Cylinder 1 Came Up
I bought an 07 gen 2 a couple weeks ago. A couple days after I got it home the check engine light came on. I did a scan, it came up, misfire on cyl
1. I installed new iridium plugs, switched the no. 1 igniter with no.
2... code came back misfire cyl 1 again.
I then did an ohm check on the injectors which were all spot on, then ran the engine and listened with a stethoscope to number 1 injector and could hear it clicking. Next thing I threw a can of Seafoam into the gas, drove that tank out and then threw a can of injector cleaner into the next tank... I forget the brand.. it's that stuff they've been selling for a hundred years that has MEK in it.
Anyway... I cleared the CEL and it's been a couple days and about 50 or 60 miles without a re-occurrence. I'm wondering if this is a common problem with prius's? (I know... but I refuse to use the word Prii... it just bothers me) Because the engine is always under such a light load, I'd think it would be prone to carboning up and such. Also... if this light comes back I'm thinking the next thing I'll do is switch number 1 and 2 injectors to see if the problem follows it.
Prius (2004-09) :: Intermittent Misfire Cylinder 1 Code
I posted this problem several months ago about a p301 code that my 2007 Prius has been generating. I eliminated all the easy stuff... plug, spark unit, fuel injector. Over the past year since I've had the car, the CEL light has gone on for a couple months then shut itself off for a couple, then back on ... probably has shut itself off 3 times in the past year, each time staying off about a month or two before coming back on. Some background on the car, supposedly the PO hit a rock and damaged the motor about 2 years ago and had the short block replaced.
Anyway, the CEL has been on again for about a month, and I got a notice for Illinois emission testing, so I decided to take it in to the dealer and have him do a diagnostic so I can get the emissions passed. After an hour and a half of testing they told me that the best they could ascertain, the car has been submerged in water, as there is a lot of rust in areas that never get any rust, and they think there's a short somewhere.
The service manager at the dealership said if it was his car he wouldn't spend the money for another 5 hours of trouble shooting, and if the car runs good he'd just drive it as is. They cleared the CEL and the service manager just charged me for an oil change as they caught a recall on the steering that hadn't been done and figured he'd let me slide on the hundred for the diagnostic.
Prius (2004-09) :: Misfire On Cylinder 2 And 4 - Car Severely Idle Rough
I own a 2007 prius, it has about 320,000 miles. It has recently been diagnosed with a #2 and #4 cylinder misfire. The car severely idles rough, but when getting in the gas it goes away. I have replaced the spark plugs, the old plugs were very white(lean), replaced fuel injectors, used fuel injector cleaner. I've sprayed carb cleaner around the intake to see if I might a leak--no leak. The motor uses about a quart of oil every 1,000 miles since about 100,000 miles. I'm just guessing, could it simply be low compression causing this? I pulled the new spark plugs after about 5,000 miles and they where white also.
View 9 RepliesPrius (2004-09) :: Misfire On Cylinder 1 After Changing Radiator Coolant
I replaced a failing two way coolant valve and went ahead and replaced the coolant. After this the heater wouldn't get hot, so figuring there was still air in the system I added more (which it took)...and repeated that twice. (and opened the top valve to allow it to bleed). Finally heat.
I got up this morning and the heater still wasn't working....so I added more fluid....which it needed. Now I have heat.
BUT, The engine started running like crap. Code says misfire on cylinder 1. Changed the plug and coil pack. This did not work. (When I pulled plug one out the end of it was dry.)
Could it just be a crazy coincidence Immediately after I changed the radiator coolant that a faulty or clogged injector rare its ugly head? The car was running fantastic before this. I thought, before I check the codes, that some way maybe I overheated the car and landed with catastrophic issues.
I have 378,000 miles on my 07 pruius
Prius (2004-09) :: Number 1 Cylinder Misfire - Error Code P0301
So I dropped my prius off to get looked at for error code p0301 number 1 cylinder missfire. They ruled out Spark plugs, coils and fuel injector. What else is ther? Also could it be the battery or even gas?
View 12 RepliesPrius (2004-09) :: Check Engine Light With PO301 Cylinder Misfire Code
I bought my 2008 Prius 9-14 with 29,000 miles on it. (rebuilt title-big mistake I now know). I found out after I bought it that it had sat for 5 years before it was rebuilt) I figured it was a miracle the hybrid battery even worked.
I had no problems until 2-4-15 when check engine light was flashing and the car was shaking. The local mechanic said was the “clutch” (torque converter), took the engine and transmission out of the car to fix it ($2200). But he realized the mass air flow sensor (MAP) was not working even after he put a new one in so had me take the car to the Toyota dealer. The dealer found a cut in the engine harness and advised me to replace the harness which he said would cost $2800. The local mechanic saw the cut via my cell phone photo and offered to fix it for free which he did.
The next day check engine light comes on after driven 25 miles with code PO 301. (means misfires in cylinder one). The local mechanic switches cylinder 1 with 4, same code the next day, local mechanic switches the coils to the cylinders, still the next day the same code. He switched the fuel injectors. Same problem of cylinder 1 misfire. He cleaned the oil out of the intake manifold, did fuel injection cleaning, and cleaned gunk out of the fuel line. Car would drive good about 20 miles then same check engine light, same code, sometimes code PO300 (random multiple misfires).
Ford F-150 (2004-2008) :: Cylinder 7 Misfire / Cylinder 6 Has Oil On Plug
06 F150 fx4 has cly 7 miss fire cly 6 has oil on plug .Check engine light comes on only if you step into the gas, The oil was low. If you drive normal the check engine light does not come on, but you can fill the miss when in gear. Change the plugs an coil add oil still no change.
View 4 RepliesPrius (2004-09) :: Oil / Fuel In Intake Manifold - Misfire For All Cylinder And Reduce Engine Power Codes
I'm getting oil and fuel into the intake manifold every couple hundred miles. Oil level is in the middle of low and full mark. It's not like it's a huge amount of oil and fuel in the intake but it's enough to make the car misfire, bog out. Only codes I'm getting are misfire codes for all cylinder and reduce engine power code (forgot what code it actually is) but that's when the car completely shuts down and won't start with red triangle light. If I clean the intake out and unplug the battery for a few min I'm able to start the car again, but it will run really rough and white smoke will start to come out the exhaust (gas smell). I'm wondering if a bad maf would cause this. I've already cleaned it but still doing same thing. Don't really know what the specs or reading the bad is suppose to be so I'm kinda stuck to determined if I need a maf or not. Cars got about 242K miles.
View 17 RepliesPrius (Gen 2) :: Misfire On Cylinder 1
Its not the spark plugs or the coil. What else?
View 3 RepliesPrius (Gen 2) :: 2005 - Misfire On Cylinder 1 And 3
Just today I acquired a 2005 Prius (trim level 1... so no options at all) in exchange for a cruddy old Ram truck and a dying Avalon. They had issues, but so does the Prius. The car has around 218K on it, I just replaced the spark plugs with NGK iridium plugs, cleaned the MAF, sort of cleaned the throttle body a little bit, and even swapped the coils around to see if the misfire would change. I also gave the car a new air filter.
View 10 RepliesFord F-150 (2004-2008) :: Misfire On Cylinder 4
2004 F150 XLT 5.4l (3v)... Problem started with misfire on No.4 and then I went through the tedious job of changing every plug (all 8 broke) and coils in an attempt to resolve the problem. After the changes I had misfire on no.1 and no.2, so I changed the injector on no.2 and coil on no.1 again + had broken pigtail wires on No.4 and No.1. Now I remain with a P0301 misfire on No.1. The problem won't go away, its fine idling, but misses bad when driving. The Snapon scanner reads fine for all injectors and compression reads ok also. The mechanics are baffled and what else could it be? (rail? computer? intake gasket?)
View 4 RepliesGolf IV / Jetta IV :: 2004 - MIL Flashing - Misfire On Cylinder 4
Just dug out my 2004 2.0 Jetta after sitting buried for 4 months. You can see a corner of the wheel there lol, its been a LONG winter. It is my car but my brother normally drives it, and while he is away at uni it just sits.
Anyways, dug it out to start it. Started right up, however after a bit the MIL began flashing. It was running a little rough. Took out my code reader and engine misfire cylinder 4 came up. The rpms are varying by 75~100 every few seconds, however nothing rough. It seemed to rev fine.
Before I put it away I got my brother to put some fuel stabilizer in the fuel. He now tells me that he put some in the oil too since it said "oil stabilizer" as well. It was a seafoam type brand... Not impressed with him there.
My question is could this just be the car waking up? Should I let it run for an hour or two to see if things work out?
Passat (B5) :: 2004 1.8t Running Rough With CEL On - Misfire On Cylinder 1
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 RepliesCamry :: 2004 - Getting P0303 Code / Cylinder 3 Misfire
I have searched but with no solid answer..
What I got - 04 Camry, 231K, never had issues, do all my maintenance myself, brakes, plugs, oil etc..
#3 Cyl misfire..
Possible causes
Plugs, - Has been about 2 years since I replaced
Coil - Bought car new in 04, never replaced
Cat - never gave it a second thought
fuel injector - put techron by Chevron just about every oil change, I know I missed one here and there..
burned exhaust valve - say it aint so...
poor compression - I have to rent a tool...
defective computer - I don't think so..
Ford F-150 (2004-2008) :: Shuddering / Cylinder 7 Misfire
My boss drives an '08 F-150 with a 5.4. The other week he had a horrid shuddering issue, misfire, and some known transmission issues so he took it to a shop. Supposedly the heads were pulled, heli-coiled, #7 coil was replaced, new plugs, trans rebuilt...a whole laundry list of stuff was done. He comes to me with complaints of a shudder in OD in low RPM primarily and a flashing check engine light with a #7 misfire code. I popped the hood to find no coil had been replaced (mechanics around here are REAL sketchy) so I told him to change up a new coil and I would throw it on to see if that fixes the issue.
Other than that, smooth idle and decent power with no shuddering except once in a while just coming into OD in low RPM...so around 40~ish and not throttling it hard. If he gets into it and blasts through the gears it has no shudder. I said the miss could be the whole issue, starting with the plugs and known misfire coil (#7) would be a good place to start.
A quick inspection in ~10 degree snow showed me the heads do not look like they were removed. The mechanic steam cleaned the engine, so looking for smudgy prints won't work. I know on older Fords the head gaskets stick out a little past the heads...do they on these too? He is questioning if the engine was even touched, and rightfully so in my opinion. Pulling the plugs would be the next step, but I need heat and tools for that.
Ford F-150 (2004-2008) :: Low Compression And Misfire On Cylinder 2
I sea Foamed the truck today. I will be pulling my heads most likely and am doing a few things beforehand just in case. History: low compression and misfire on #2. Have changed plugs and swapped out cops. Paper against exhaust pipe sucks in and pops against the pipe intermittently. Seems like intake valve.
Anyways, poured in a whole damn bottle through the brake vacuum line. The engine sputtered a bit but never stalled. I saw almost no smoke after a whole bottle!! I thought with 156000 miles it would smoke like mad. I have taken very good care of this truck and changed oil every 3 to 5 with synthetic 5-20 since new. Could it be that clean???
Prius (2010-12) :: Code P0304 Misfire On Cylinder 4
Well, I have a big problem on prius 3, the problem is that it has a big and I mean a big body shake when I decelerate above 30 mph or slowly accelerate above 30 to 50-70 mph, when I fully accelerate, the body shake disappears. When the body shake occurs MIL comes blinking and DTC P0304 comes but not always, but the shake is only when the coolant is hot.
On the other hand, if the MIL is not on with the tester it can be seen that the cylinder 4 has misfire margin, only cylinder 4, every time. Now what I have done is to exchange the injectors, problem remains on cyl4.
-replaced the coils, problem remains on cyl4,
-clean the EGR, problem remains on cyl4,
-opened the engine to see the valves, cylinders, pistons, exchanged the ring set,problem remains on cyl 4,
Replaced the wheels, the problem is still there, now I want to replace the drive shafts.
Pontiac - Grandprix :: 2004 - Cylinder 3 Misfire And Gas On Spark Plugs
Ok , i have a 2004 Pontiac Grand Prix GT V6 GM 3.8, my car didnt have any misfires until after i changed my Lower Intake Manifold Gaskets. After changing the gaskets and putting everything back together. The car ran fine. The next day i took it an hour and 30 min away, while driving there it started misfiring and shaking,rough idle at an hour into the trip. The check engine light went to blinking. The Next day i drove it all the way back home in the condition. Put code scanner to it, and received P0303 "Cylinder 3 Misfire":
So i automatically assumed it was the coil pack because i just installed new wires and plugs a week before changing Lower Intake manifold Gasket. Bought new coil pack. Still getting rough idle and P0303 code. So i decided to take a look at Cylinder 3 Spark plug and it was dry black, carbon fouled:
So went and bought new spark plug, installed it, started car and still rough idle and misfiring. Took the new spark plug out and it had been FOULED also ( DRY BLACK AGAIN). So i was told to switch a coil pack around. I did it and the started car, took away some of the rough idle, car actually wasn't misfring or shaking, would run smooth for about 5-8 seconds then start misfiring (Didn't that until i switch coil packs around).
Next Decided to pull out the rest of the plugs from the back and all of them were WET with GAS!! and 2 Spark plugs are just dry fouled!! (Cylinder 3, Cylinder 1). If I can figure this out i will fully have my car back to running correctly.
GTI 337/20th Anniversary :: 2004 GLI 1.8T - CEL Came On / Code P0303 Cylinder 3 Misfire
So I have a 2004 Jetta gli 1.8turbo and my CEL came on last night from normal driving, after it came on it still drives the same. I had it scanned for codes and got the p0303 cylinder #3 misfire. wondering what could be the solution for this? I dont think its the coil pack because I had them changed at the dealer from the recall about 2 months ago (anyway to check?) Also I have 97,000 miles on my car and my last oil change I used 0w-40 oil. I know this is probably not the best oil to use at this mileage but I had an extra 5 quarts of them laying around so I decided to use it.
View 24 Replies