Chevrolet - Blazer :: Rubber Door Molding Separated At Front Corner Of Both Doors
The door molding has come loose at the front corners of both my doors on my 2002 S-10 pickup. I tried weldwood contact cement (the kind you use on laminating Formica counter tops), but it only lasted a couple of days. I put a spot of super glue on it to see if that might work. It looks promising but that little spot that I tried was not enough surface area to hold it for more than a day. I don't want to ruin the trim by super gluing the whole thing if it won't work. How to do this? The trim seems fine otherwise. It is not cracking or anything like that. I think super glue would hold it if I glued the entire length of about a foot or so. Also the driver side door seems to be a bit out of line an eighth of inch or so at the front corner. It does not appear to be adjustable. It has never been in an accident. It does not seem to be leaking into the cab yet with the door closed.
View 2 RepliesLexus LS 2007+ :: Front Window Rubber Molding Replacement?
I have noticed that the rubber window moldings around both front doors is deteriorating. Both are torn and falling apart. There is no wind noise yet but they need to be replaced.
View 2 RepliesLexus RX 2010-15 :: Rubber / Felt Window Molding Pops Out On RX350
Our new (got April 2014) RX350 seems to have an issue with the rubber/felt window molding getting caught between the glass and metal incorrectly. "Pinched".
View 1 RepliesPhaeton :: Rear Molding Lower Door Separated From Car Body
I've noticed on both rear doors, the Lower Moulding (black cover at the bottom of the door) #12 in the attached diagram (Light Blue Circle), is very much separated from the body of the car, it's like bended toward the outside, but it seems to be exactly the same on both sides, I am not sure if this is normal or mine has a defect
Both front doors are OK, not 100% perfectly aligned with the body of the car, but MUCH better than the rear doors....
Sonata I45 (YF - 2011+) :: Odd Rubber Sound At Top On Raising Driver Side Window
On raising the drivers window, there is an odd rubbing/squeaking sound that appears to be coming from the were the glass is running along the rubber seal (B-Pillar side), during the final 2-3" of travel. While certainly no rubber expert (), I don't see anything out of place. It closes all right.
View 3 RepliesLexus GX 2004-09 :: Driver Side Door Molding Clip Missing
My driver side door molding is missing a clip. This is the bottom half of the mold and one of the clips snapped off. I've checked junk yards and they never have any GX's. Just to elaborate the clip I'm missing is on the exterior side of the door, down by the bottom edge.
View 2 RepliesLexus GX 2004-09 :: 2008 GX470 Molding Between Driver Door And Roof Popping Out
Have owned my 2008 GX470 for about 8 months now and love it. However, over the last month I have noticed the molding between the driver door and roof has been popping out. I don't know if there are clamps down in there that have fallen out or if the molding just needs to be clamped back in. Picture is below.
View 5 RepliesPrius (2004-09) :: Driver Side Window Will Only Go Down Half Way
My driver's side window will only go down half way. The problem began when a small accident damaged my driver's side door check (the small bar that keeps the door from swinging open too wide). The check was bent, and the window stopped going all the way down. When I removed the check, the window worked fine. Now I've replaced the check. The door works fine, but the window problem has returned.
View 1 RepliesPrius (2004-09) :: 2007 - Driver Window Won't Open
I just took my 2007 Prius into dealer to repair the driver's side window which hasn't worked for several months. (locked in closed position - others work)
Service dept says I need a new switch which will cost +$500 plus labor. Could that be right?
Prius (2004-09) :: 2008 - Driver Side Window Goes Up Then Down A Little Bit?
I have a 2008 Prius, but my wife drives it. I think this problem has been going on a long time, but because my wife drives the car, I never noticed it. When I raise switch to raise the window on the driver side there is a little click after which the windows should roll up to the top and stop with out holding the window switch.
Mine does this, however it gets to the top and then drops back a little. This does not happen if you don't engage the automatic roll up feature.
I found a couple of threads that talked about window calibration, but I cannot find anything more than that.
I found this link but it just goes to the home page of priuschat
Prius (2004-09) :: Film Peeling On Driver Side Window
There's a film peeling off the inside of the drivers window. I didn't even know there was a fim there, I assumed the tint was in the window itself. It appears that it is shrinking away from the left edge and along the top of the window itself. The piece along the top edge has peeled off and is now actually flapping in the breeze! 1/8 to 1/4 inch, tops.
View 5 RepliesPrius (2004-09) :: 2008 - Driver Side Window Will Not Close Back Up
I replaced my auxiliary battery yesterday and everything was working fine. This morning my driver side window will not close back up. All the other windows are working fine. I drive a 2008 Prius btw with roughly 50000 miles....
View 8 RepliesPrius (2004-09) :: 2005 - Leak From Driver Side Rear Quarter Window
I just bought a 2005 Prius a couple days ago and have spent the weekend discovering "hidden" little issues. One was that after a heavy night a rain there was a small pool of water in the very back of the car underneath the cargo area near the wire that runs from the traction battery. In fact the little prongs holding a slim white (electronic) box connecting to the battery were rusted out.
View 3 RepliesPrius (2004-09) :: Driver Side Power Window Excessively Loud Going Up And Slower To Rise
I drive an '04 with about 86k. Shortly after I hit 85k i got into an accident that required both drivers side doors and the drivers window to be replaced. 2 weeks ago I noticed that my driver's window was excessively loud going up and slower to rise than the other windows. Upon closer inspection it seems that the rubber surround at the front part of the window gets bunched up requiring the motor to work harder to get the window all the way up. I fear that it is only a short time before the motor fails and the window becomes useless.
I plan to go back to the body shop and have them take a look at it. I am not fully sure if they caused the problem, my common sense tells me that the drivers window ought to be the first to fail, seeing as it gets used the most (garage tickets, drive throughs etc. But I am hesitant to replace the motor if the repairs were done improperly causing it to burn out). How much the motor runs? I am guessing that this will not be a cheap repair, but my hope is that the body shop will at least do the labor for free seeing as they replaced the window and the door and I now have this problem. I have to take the car back anyways, they replaced the fender and it is loose at the top.
Prius (2004-09) :: 2005 - Driver Side Power Window Clicking After 12V Battery Change
I have an issue with Prius 2005 driver side power window constantly making clicking sound even after turning off the Prius. All other power windows works, just the driver side is having this issue. This started happening after I changed the 12V battery for my Prius.
The window still rolls down and up but it's very slow and making even louder clicking sound while rolling down and up. Also an other thing that I noticed is that windows keep going down slowly by itself after it's been closed. Any clue as to what went wrong with my driver side power window ?
Camry :: 2010 - Chrome Window Molding Removal?
I would like to remove the chrome window molding around the front and rear doors of my 2010 Camry. Is it difficult to remove? More importantly, when I go to reinstall it - is it difficult to get straight like OEM fit and finish?
View 3 RepliesCamry 2012+ :: How To Replace Window Pillar Molding
Long story short, the tint shop burned my exterior door pillar when I got it tinted like 8 months ago. Just now felt like dealing with it, so I got the new part in. How to replace it? The back has a lot of what looks like double sided tape and only 1 clip. In order to get the other one off it looks like I have to take off the chrome strip at the bottom since the black molding goes underneath the chrome...
Pic of how the molding is on the car ....
Pic of the back of the new one ....
Ford Ranger / B-Series :: 2000 - Window Belt Molding?
A C-note for those 2 pieces of nothing seems ridiculous. Considering sanding and painting instead.
View 2 RepliesPrius (2004-09) :: Bottom Molding Detached After Windshield Replacement
Maybe "detached" is the wrong word, but it's sticking up a bit on one of the sides such that it's not touching the windshield (see attached picture).
I don't think it was like that before, however, and I'm wondering:
1. Should I even care?
2. Is there an easy way of making it sit flush that a non-car guy could handle?
3. Is this something I should call the windshield guy back to do?