Passat (B5) :: Rough Running Engine / Bucking / No Power / Slow Start / Low RPMs
I dont know if this is related but my ignition switch went a few weeks ago, I got the part in the mail this week and was planning on changing it today, but a few days ago my 99 Passat v6 started bucking, kinda like it did when i needed motor mounts...but my engine is really weak and rough. I opened the hood and saw that my air filter hose was disconnected right after the MAF (or at least i think its the MAF).... I don't know how long its been sucking up dirty air. but does that sound like they are related? a friend of mine said if i can see the butterfly valve in the air hose, open it up and spray a can of carb cleaner in it, put the filter back on, start the car and let it run, then do it again with another can and it should fix it. I cant see the butterfly air valve in the hose, since the hose goes down behind the engine. Should i just spray it in anyway? or does have to be press on the gas pedal...
View 3 RepliesFord Super Duty (1999-2016) :: 2006 F250 Running Rough / No Power On Acceleration / Code PO420?
CEL came on last night, OBD code PO420, truck is an 06 f250,5.4? Btw, truck running rough, no power on acceleration, in gear at idle, runs rough....
View 4 RepliesPassat (B5) :: ECU And Engine Running Rough
My car recently started running rough (felt like it was misfiring). I took it to a local mechanic who went through all the normal possible problems and determined that it was a computer issue but did not have the equipment to diagnose it. I then took it to a VW dealer who said it was a bad ECU. They wanted a fortune to replace the unit so I sent it to a ECU repair shop in the UK. The repair shop said there was nothing wrong with the ECU and I have since put it back in the car which still continues to run rough. What else may be causing this issue especially considering that the VW dealer said it was a bad ECU but the repair shop said it was not?
View 1 RepliesPassat (B5) :: Running Rough And MPG Dropped
Car has been running a little rough and the MPG has dropped from about 26 MPG to about 23. could i need new coils? the check engine light is NOT on. can they be bad without the light being on?
View 3 RepliesPassat (B5) :: Car Running Rough And Engine Light Came On
So- I take the variant in for a 65000 mi service- i.e oil change- and to get the recall done on the crankcase hose. I pick it up, drive out, and at first stop sign --- it starts running rough and engine light comes on. Take it back- they throw the computer on it and it throws a code for vacuum leak connected to brakes.. they take it back-pick up next day---they had to replace the brake booster (under warranty, extended-nice of em, I guess), because, they say, the cowling plug was plugged and water filled the booster. I HAD smelled musty water smell. But- why did it just go in the shop?? 60 bucks to unclog drain- W.
View 3 RepliesPassat (B6) :: 2007 - Burning Oil And Running Rough
I had an incident in December where we left the house and drove less than a mile when the oil warning came onto the MFD. I pulled into the local gas station and had to pour two full quarts of Mobile 1 in order to bring the level up onto the dipstick.
As the car is still covered by the VW Assured warranty, I had the dealer check it out but was told that this is "normal" though we never had it happen before (owned for two years). Really, two full quarts is normal?
Now, we have had two incidents since then when the car starts rough and the check engine light flashes. With the first incident, the dealer found that one of the coil wires had "come loose." It is back at the dealer now for the second incident, but i don't see a cable coming loose twice in just a few weeks.
Could these be related to the oil incident? Car is a 2007 early build (2006) wagon with the 2.0T ....
Passat (B6) :: Engine Running Rough And CEL On - Misfire On Cylinder 2 And 4
I'm having an issue with a 2008 Passat 2.0T. Engine ran rough one day and check engine light came on! I get the VagCom out, scan the ECU and get misfire on cylinder #2 and #4. Car has 109 000km. Plugs were never changed so I order some new OE Bosch platinum iridium plugs. Go for test drive after having change the plugs and I still get misfire on both cylinder number 2 and 4.
I know coil on plug are prone to be weak on those engines so I go ahead and order 4 new coils which are pretty low cost which is good. Once install on the car I go again on a test drive. car ran really smooth and no check engine light came on. I said fine! I fixed the problem only to discover the day after that the CEL decide to come back on I scan again and this time only get misfire on cyl #2 with fault frequency of 39.
I suspect my injector to be bad but before I decide to remove the intake manifold and spend another 2-300$ in parts. Any way to test my injector with VagCom in order to see if that really is my problem. Also heard the PCV could be a problem but i hardly doubt it would throw a fauly code on just one cylinder.
Passat (B5) :: 2004 1.8t Running Rough With CEL On - Misfire On Cylinder 1
My 04 1.8t is running rough with the cel on. i scanned it and cyl 1is misfiring. tried changing plugs. seemed to work while idling but as soon as i accelerated it started running rough again.
View 4 RepliesPassat (B5) :: 1999 1.8T - Running Rough When Idling, But Only In Drive?
I just got my first dub, and it is a project car. I have had it serviced and it still idles rough when in drive with foot on the brake but idles normal when in park. a
View 2 RepliesPassat (B6) :: Running Rough / Surging When In Drive And Stopped
Had the oil changed yesterday and changed the air filter myself. Car is now running rough, surging, when in drive and stopped. Runs cleanly when moving and surge is significantly less in park and neutral.
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ford 6.7L Power Stroke Diesel :: Running Rough / Reduced Engine Power
I am having a problem with a 6.7. The truck has 9900 miles on it. It has a dpf delete, egr delete, Spartan tuner and a snow stage 3 kit. The truck lopes at idle but once throttle is applied it levels out but still runs a little rough. Its keeps saying its in reduce engine power no matter how many times I clear the code. If I clear the code it will come back in 2 seconds with out cranking the truck or anything. Rail pressure is telling me 31090 psi and not changing running or not. I have changed rail pressure sensor, and pressure control valve with no result. The green and violet 5 volt reference that feeds those sensors is only putting out 1.2 volts. Put a new pcm in it still the same and now has quit running totally. The codes are P0193, P0335,and P06A6.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: 2000 - Running Rough - Missing - No Power
2000 F250, 7.3, 170K, running rough, knocking loudly, missing, shaking, no power to get up driveway, intermittent, no codes spit out at all. No smoke visible, no leaks visible, New fuel filter, air filter, update cam sensor, new fuel rail lift pump, new uvc harness, new glow plug relay.
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough And Had No Power / Died While Driving
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
Ford 6.0L Power Stroke Diesel :: 2005 F350 Running Rough - No Power To Move
I got a 2005 f350 6.0 deleted and studded with air dog 2 4g pump, 125k miles. It started running rough then just died all within a few miles tuner showed code for injector 6 and ficm towed into ford dealer didnt have time to mess with it. They said ficm was bad had them replaced it then they said i need whole new fuel system lines,harness,pump,sending unit ,tank the whole 9 yrds. Which i thought was uncalled for so i called up airdog which system i had on there and they laughed and said ford garage is full of bs that they will upgrade my pump to the 4g and new harness.
So I took that stuff to garage had them swap it out and now they said come get the truck they wont work on it anymore that now it needs 3 injectors and they wont touch it with aftermarket fuel system on it. So I go to drive it home and it starts but runs rough and u can hold it to the floor and it wont budge bearly idles up and builds no boost my tuner is showing injector 2,3,4 now which wasn't a problem before i took it into the garage. So im not sure what happened to cause this all to happen but before i sink any more money into it is the 3 injectors enough cause to make it not build boost now .
Ford 7.3L Power Stroke (1999-2003) :: Rough Running / No Power After Just Driving A Block Or Two
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 7.3L Power Stroke (1999-2003) :: Running Rough When Accelerate / Bogs Down And Looses Power
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 RepliesPassat (B5) :: 2004 Running Rough / Burning Smell Of Oil Or Rubber
Had this problem yesterday and drove my car home about 3 miles running very rough and very sluggish! I could smell something like burnt oil or rubber when I stop but not too bad_no smoke. We are at a ski resort and will have to drive our vehicle about 70 miles to nearest vw repair shop. Is it ok to drive my passat with this rough condition? I am guessing ignition coil or spark plugs.
View 4 Replies