Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 Missing Mostly Going Uphill And Running Sluggish
Lately I have been having problems loosing power. Truck wants to miss mostly going up hill and runs sluggish I'll pull off the road and let it idle for a minute and it will run fine. And it is only occasionally some days it don't happen at all and other days it happens quit often. New fuel filter, oil is good, had it on the scanner and isn't throwing any codes. Around 230k miles newer injectors.
View 10 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Bad / Missing Like Starving For Fuel
2001 193K miles. Has a miss, like starving for fuel. Starts fine and it will clear out at higher RPM, 1800 and up. idles...
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Loss Of Power / Rough Running
I have a 2001 ford 7.3l powerstroke diesel. When I first noticed the problem I was towing a trailer going up a grade and got into the throttle almost to the floor and noticed a loss of power and the service engine soon light flashing extremely rapidly a few times and never came back on. I made it home, still lacking power but not running rough. I drove the truck to work the next day and the truck was running rougher and loosing power. It ran great through lower RPM's but seemed to trip as soon as you gave it over half throttle. eventually the truck wouldn't run right at all and lacked complete power. It idled rough as well. My mechanic threw the computer on it and it said injector pressure reading too high or too low.
I was told to replace the IPR on the HPOP and I did. (I also replaced the fuel filter and changed the oil). After replacing the IPR it ran great, had full power! then it began to slowly die like it did before until it sounded like it was running off 4 cylinders again. I pulled the ipr out, cleaned it and changed the oil again. It seemed to clear it up for an hour and ran great but then began ran rough again. I also replaced the CPS sensor. I feel like its not getting enough fuel or something, im just wondering if it could be the ICP or the lift pump. There is no check engine light at all. Its just got me stumped because cleaning the IPR clears everything up.... temporarily.
Ford 7.3L Power Stroke (1999-2003) :: Running Rough And Had No Power / Died While Driving
Well, I was headed out from work this morning, on my way to fill up as I was a bit below 1/4 tank.
Truck was running good, like normal, until after 5-6 minutes, when it started running rough and had no power. Worried, I pulled off the side of the road. As I did so, it died, and wouldn't start again.
I whipped out my phone, pulled up TorquePro, and ran a code check. Nada. Well, it sounds to me like it's not getting fuel possibly, so I figure the best way to check, is to drain the fuel filter bowl, and crank it some, and check the bowl. No fuel in bowl.
Wifey came to pick me up with the can of diesel I keep for starting my forge (had 3 gal maybe?). Poured it in the tank, cranked it, no start. Still nothing in the bowl.
I'm taking her to work now, so she won't be late, then I'm headed back with a full can of diesel.
If that full can still won't get it, should I keep shuttling diesel cans, or should 8 gal or so be enough to get it back to the fuel pickup level? And if it's not fuel level, what else should I start checking on the side of the road?
Ford 7.3L Power Stroke (1999-2003) :: Rough Running / No Power After Just Driving A Block Or Two
I have had this happen twice now. Starts fine, idles fine, then either sitting or just driving a block or two it starts running very rough, no smoke that I remember seeing, and now no power. Barely makes it up a hill. The first time I thought is was related to the heavy rain the night before. I had the tow truck coming and decided to try it again, this was after a few hours sitting. Ran perfectly. The second time, no wetness/rain, pulled away from the house and in a block or two, same thing ... rough, no smoke, no power. Pulled back into driveway, turned off for a minute, restarted and ran fine. Ran perfect today. What is the best injector cleaner to use in the fuel?
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: 2002 F250 Idling / Running Rough And No Power
2002 F250 7.3L suddenly idling and running very rough, and doesn't have any power. Truck has been running perfect, it's my daily driver, and just put a couple hundred miles on it yesterday with no problems. I had been having some transmission issues when I tow heavy so I bought a new transmission yesterday. This morning I pulled the truck into my garage to change the transmission. Again truck ran fine, no signs of any issues before the trans swap. I changed out the transmission, which included unhooking the trans wiring harness from all the various sensors, and unbolting the starter.
I didn't mess with anything in the engine bay except for unhooking the batteries. I had also repaired the overdrive button wires, as they had been pinched in the steering column and the button wasn't working. When I got everything hooked back up I cranked it up to get the trans fluid flowing through the transmission, it started right up and idled good. I had it running for a few minutes and it was beginning to make a little more noise than usual. When I started to back out of the garage it was getting pretty rough, almost like it was running out of diesel. I put it in neutral and gave it some throttle and noticed I was getting white smoke out of the exhaust and could smell diesel pretty strong.
I checked my injector resistance at the valve covers and got around 4 ohms +/- on all of the injectors. I rechecked all of the clips and harness that I had messed with. I took a look at the ICP sensor and it has oil in the connector which I know can cause a rough running condition in some cases. It looks like it has had oil on it for a while. I unhooked the batteries again for about 20 minutes to try and reset anything that may have messed up. I checked a bunch of connections under the hood to see if anything was unhooked or loose.
I also cleaned up the connector on the ICP sensor. I started the truck back up and it idled perfect so I pulled it back out of the garage and headed down the driveway. It almost immediately started running rough again and barely had the power to go up a small hill. I pulled back in and tried unplugging the ICP while it was running, which made a slight difference in the idle but still very rough. I plugged it back in and the idle progressively got worse until it was chugging really bad. I shut it off after that and haven't messed with it again.
What might have happened? Could it be a bad sensor or transmission position sensor in the new trans? Is it just coincidence that this happened with a transmission swap? I am going to get a new ICP, but if there is anything else I can try/check before I can pick up the ICP on Monday let me know.
Ford 7.3L Power Stroke (1999-2003) :: Running Rough When Accelerate / Bogs Down And Looses Power
I was wondering if fuel injectors throw a code when it goes out. I have a 02 7.3 been running rough when you accelerate bogs down and looses power not sure but sometimes gas light would come on knowing I have gas in it could that be a sign of the sending unite and that's why it runs rough..
View 3 RepliesFord 7.3L Power Stroke (1999-2003) :: White Smoke / Rough Idle And Missing
I have a 2001 7.3 that almost has everything practically brand new... new hpop, water pump, uvch, gpr, glow plugs, icp sensor, ipr sensor, cps and new turbo pedestal that was leaking oil, well now my truck has a cold start to where it has to be plugged in to start and when it finally does it smokes white pretty bad, misses and sounds like it's jumping around under the hood up until it warms up and revs fine with less white smoke but still a miss!!
Compression on test has been done, and good, fuel pressure is good, but the buzz test when cold shows 123457 muffled and quite and when the truck is warm only 3 and 4 are still muffled and quite? Injectors sticking?? Or just need New injectors!
Ford 7.3L Power Stroke (1999-2003) :: 2001 F350 - SES Light Came On / Truck Started Running Rough And Lose Power
I have a 2001 F350, 7.3. My service engine light came on and immediately the truck started to run rough and lose some power. I've checked the under the cover connections and they were both connected, I replaced the cam position sensor and I still have the same problem. The worse part of the hold thing is that there are no codes stored so I'm flying bind. Where to go next.
View 8 RepliesFord 6.0L Power Stroke Diesel :: 2005 Missing / Truck Started Running Rough
So I have been fighting a rough running, missing problem. My truck started running rough one day on the way home. I got it scanned, it showed injector contribution balance 1&2. Made sense to me that it threw those codes. I replaced 1 and 2 with oem replacements. Got that all done, truck still ran like crap. I changed fuel filter with motorcraft ones and drained the water separator. That didn't work. I am getting it scanned again, so i will have codes shortly.
Also, for a while it would run with absolute no problem. It was intermittent like that. Run bad run bad run bad and then one day run flawlessly. I though it was electrical. Checked all the common places for chaffing, saw nothing. Even did the wiggle test while it was running, no change. But it hasn't been intermittent for a while now.
Ford 7.3L Power Stroke (1999-2003) :: 2003 - Running Rough / 2 Cylinders Not Working Correctly
I have a 2003 F250 7.3L. I put new injectors in my truck four months ago and all of a sudden, I have 2 cylinders not working correctly, making the truck to run really badly. I sent the 2 injectors from the bad cylinders back for warranty and they replaced both of the injectors but nothing was wrong. I put them in and the truck still runs badly. I have a new fuel filter, new ICP, new CPS and glow plug relay. I cannot drive the truck, it smokes white at idle. I can unplug each injector at a time and cyclinder 5 does not change how the truck runs
View 14 RepliesFord 7.3L Power Stroke (1999-2003) :: Truck Running Rough And On Less Than 8 Cylinders
I had an HPOP line burst and soak the engine compartment with oil. I replaced the line and degreased the engine and rinsed it off. I started the truck and let it idle for 15 minutes or so before driving it. On the way home right after a shift it started chugging and running terribly. The check engine light was on as well. I limped it the mile or so home and shut it off. I restarted it and it runs just fine. I checked the DTC's with Forscan and there were a bunch of things that were mostly related to the HPOP and the MAT sensor that was shredded when the line blew. I left the hood open to dry out today and I'm hoping it is just some water in a connector. Does that sound plausible?
View 6 RepliesFord 7.3L Power Stroke (1999-2003) :: Running Rough And Cannot Pull When Put It In Drive
I bought a 99 7.3 been in the trees for a few years pulled it home and now trying to get it running. Did a service new filters and oil fuel too. I can get it to start and will run but runs very rough and if you put it in drive cant pull its own self. I don't have a check eng light on. And found out my scanner is a pos lol. it will hooked up and then try to pull codes and loses it connection. But that's the scanner will not work on my other 7.3 as well.
I am making high pressure oil checked off the rail with gauge and it will build up to 2000 psi when I rev it. but missing like crazy. I swaped the pcm and idm out of my running 7.3 and it didn't change a thing. I have checked the pass though and they are fine. pulled drivers side valve cover off and no oil leaks when running and rockers are fine. new ipr valve as well too. I know I need to get a scanner to talk to this thing better.
Ford 7.3L Power Stroke (1999-2003) :: 2000 - Truck Missing And White Smoke Coming Out - Code P1316
Recently I have had many problems with my 2000 7.3l .... The one I cant get rid of is the p1316 code. I have changed out the uvc harness and gasket with new ones, then removed valve cover's to double check connections again and they are fine. I am getting white smoke and the truck misses. I do not have a advanced reader for the codes just using my edge programmer. I have also disconnected the battery and cleared the code but it comes right back.
View 14 RepliesFord 6.0L Power Stroke Diesel :: Rough Running Like Missing When Cold / Puffs Of Blue Smoke From Tail Pipe
My truck has been having this issue pretty much since I have had it, but it seems to be getting worse, or so I think.
When the truck is cold, it does not want to move very well. Like it's missing, and it does this until it gets warmer. Also, I have puffs of blue smoke come out the tailpipe when this occurs with it cold.
Injectors? Injector o-rings? Stiction?
FICM volts are good at 46.5v-48v when cranking.
Ford 7.3L Power Stroke (1999-2003) :: CEL / Rough Running / Smoke Blowing When Cold
I had been fighting some problems with injectors for several years. I didn't have time to dig into it. I knew what I needed to do, just needed to find time to do it. I honestly thought it was and injector and thought I would have to go to new sticks because I've had so many problems with the remans.
Well I finally had time last week. I pulled the passenger side valve cover and ohmed the injectors. It would be almost impossible to get the leads in the injector while installed the truck. I kept an old valve cover harness, so I cut a pig tail off of it and plugged it into the injectors so I could test. You can see the meter attached to the pigtail in the pic.
To my surprise all four were all right around 2.7 ohms. You need to set your meter so you are getting a reading w a decimal. If you set it to high it will only show a whole number and it is better to have a more accurate reading.
I then plugged the wiring harness back in and tested it from there. The #7 injector gave over 6 ohms. This told me that my wiring harness was bad. I went OE and replaced it. I had a problem w a Dormant valve cover gasket before so didn't want to go that route. After I replaced the gasket and harness all my readings were under 3 ohms. They were all lower than w the old harness.
Ford 7.3L Power Stroke (1999-2003) :: Rough Running / Stumbling With SES Light And Eventually Die
So the last couple times I got a car wash the truck started running real rough, sometimes dies, then runs fine after a few minutes. Well, the last car wash I got it did it again, but the issue didn't go away. I checked the injector plugs, cleaned and greased, no change. Validated the bowl is filling with fuel, changed fuel filter, no luck.
Sometimes it will start and idle fine, rev in neutral fine, if you come off throttle abruptly it will fall below normal idle and start stumbling with an SES light and eventually die.
I managed to get it idling good, started logging with TPro (attached) and it was throwing codes P0475 - Exhaust Pressure Control Valve, and P0705 - Transmission Range Sensor Circuit Malfunction, as well as P1211, p1249, p1316 listed as 'multiple descriptions'.
I'm assuming this is an electrical issue since it happened after washing the truck, just not sure what sensor would cause all this?
Ford 7.3L Power Stroke (1999-2003) :: F250 Surging - Running Rough - Dies?
I have a 99 f-250 with about 250k miles. Truck is completely stock. It recently has developed a problem where when I start it in the mornings it surges at idle, 200 rpm or so. Sometimes it tries to die and did once but started back up. When driving it continues to rev itself up and is jerky. It runs rough and sounds like it could be missing on a cylinder. At other times it runs fine just like normal. Yesterday morning it started with these symptoms so I put in a new ford CPS. It ran great for about 100 miles that afternoon. This morning it started back with the same symptoms. The SES light stayed on longer than normal when I started it, but it went off. I don't have a scanner.
I thought it might be water in the fuel because this started the day after I filled it from my transfer tank. But the water in fuel light has never came on. I put a new fuel filter on it but it made no difference. Have pulled filter three times looking for water but never found a drop. Also pulled several buckets from the bottom of my transfer tank but found no water there either. Where to look next?
Ford 7.3L Power Stroke (1999-2003) :: 2000 F350 - Missing After Start Up - High Idle - Got Codes P1316 / P1211?
Well, long story is that I starting have problems with my 2000 F350 Dually 7.3 PSD about 6 months ago ( ~10K miles ago ). I have sunk almost 5K$ in mechanics and the problem is still present.
By troubleshoot, I do not mean try this, try this, as that has been what is happening. I mean making test measurements and diagnostics. I am fairly mechanically inclined, but I am no mechanic. Looking for primers on how the 7.3 PSD works.
Symptoms: After the truck sits 12 to 14 hours, it starts and idles fine ( ~ 700 RPM on the 'Dash Tach' ) just as it has always done. During the first 5 miles of driving it, the SES light comes on and it sputters, stalls, and vibrates as if a couple of the injectors are not firing. It then clears up and the SES light goes out, except that it idles at about 1200 RPM ( 'Dash Tach' ).
It runs fine like this the rest of the day, If I shut it down it will start right up and run fine, but it has the high idles. Only if it is shut down longer than 12 to 16 hours do the symptoms, other than the high idle, reappear. The high idle is constant. Also mpg have fallen ( 13 opposed to 16 ).
It does not seem to be related to ambient temperature, or the amount of warm-up idle. I have idled it for three hours on startup and it is fine, until I drive the first 5 miles or so.
Now, I have had three mechanics work on it and they have replaced: the ICP sensor ( 3 times ), the Fuel filter ( twice ), drained, flushed and refilled the HPOP, replaced both sides of the valve cover wiring harness, put in a new IDM, fuel heater, CPS sensor ( 3 times ), fuel pump in fuel tank, EBPV ( not sure what this is ), and the last straw was saying the injectors needed to be replaced ( or at least the O-rings, but while we are in there you might as well ... ).
I bought a cheap code reader and it says: P1316 & P1211. I believe these are the same codes since day 1.