Sebring - Chrysler :: 2010 - Connector Removal From Brake Light Switch
How to remove this type of connector from the brake light switch? I've tried just about everything at this point. Sheer force alone doesn't work. There has to be some type of release mechanism I'm not seeing that allows it to disconnect.
IMG_20161111_1433060_rewind.jpg3120x4160 1.96 MB
Passat (B6) :: Rear Bumper Removal For Hitch Installation
I will be installing a Euro-type of hitch to my car and for that the rear bumper needs to be removed.
View 8 RepliesPassat (B7) :: Driver Side Kick Panel Removal For Speakers Installation
How to remove the drivers side kick panel? It has the hood release lever, which is holding me back from figuring out how to get it off. I don't want to keep experimenting because of the chance of breaking something. I'm trying to install some after market speakers and need to get behind it to run the speaker wire to the door.
View 3 RepliesPassat (B6) :: Brake Light Switch Went Out?
My brake light switch went out at 93,000 miles. It is a recall issue with all the other models but not the passat. So I guess I have to change it myself. But I can't find the switch.
View 2 RepliesPassat (B5) :: Brake Light Switch Failures
The brake light switch on my '05 failed Friday. The '04 it replaced and the '03 we still have had brake light switch failures, too. Obviously, this can be pretty dangerous. I suggest that all Passat B5/5.5 owners check their brake lights frequently until VW gets it together and has a recall like they did for other models.
View 4 RepliesPrius (2004-09) :: 2006 - Tail Light Removal And Installation
Looking for detailed instructions to remove the RH tail light from the '06 Prius? I reviewed the '07 Prius tail light removal discussion [URL] .... but I'm stuck at the step where I need to remove the long bolt. What should I do now?
View 4 RepliesAccent RB (2012+) :: Front Bumper Removal For Fog Light HIDs Installation?
Installing some fog light HID's and was wondering how to remove the front bumper.
View 7 RepliesPassat (B6) :: 2008 V6 - Headlight Switch Removal
How do you remove the headlight switch on a 2008 Passat B6? i tried pushing it in and turning it right, but i still cant pull the switch out. Am I doing something wrong, or does it not come out on this model?
View 6 RepliesPassat (B6) :: 2006 - After Installation Of ECS Tuning Brake Kit Squeaking
I have purchased this front brake kit from ECS tuning and installed them on My 2006 Passat, After I installed them and took for test drive and initial breaking is good better that before bat notice some squeaking when rolling slowly like before stop light, only on light applying break pedal not if I have to hard break, I said maybe they need too wear in or so... It now more that month and squeaking is becoming worse. Is it bad kit or something else that causes this problem...?
View 1 RepliesLexus LS 2007+ :: Flashing 3rd Brake Light Installation On LS460L?
Installing one on a LS460L? Can you buy just the bulb and pop it in or is it a big wiring job? I think they are a pretty good safety feature (the way the crazies drive in this City anyway) and I assume it would be an easy DIY install?
View 1 RepliesGolf/GTI VII :: 3rd Brake Light Removal?
How I can access the 3rd brake light in the hatch spoiler?
View 15 RepliesPassat (B6) :: 2010 - HID Fog Light Installation Need Error Eliminator?
I have a 2010 passat and I'm going to be installing DDM 35w 6000k slim ballast on both my low beams and my fog lights. The guy at DDM told me I needed Error eliminators, is this true? also besides the HID kits and the Vagcom changes is there anything else I need to do to make these puppies function properly? like use a relay for the fogs?
View 16 RepliesFord Super Duty (1999-2016) :: 3rd Brake Light And Pedal Adjustment Switch Does Not Work - ABS Light On
Was checking fuses for why my 3rd brake light and pedal adjustment switch does not work. Was also looking for a fuse to tie into so that a light in the cab floorboard will stay on when the headlights or marker lights are on... After trying several spots to no avail (finally putting it into the bright headlight fuse). I got the light to work.... But now my ABS light stays on!!! Also 3rd brake still not working...
View 1 RepliesPassat (B5) :: After Installation Of Turn-signal Arm Airbag Light Stays On
Over the past 2 days I drove without the center of the steering wheel in place because I was in the middle of removing the turn signal arm - I had to wait until I found a T55 torque bit for removing the steering nut. Anyway, the I installed a new turn-signal arm and re-assembled the steering wheel and such. Even after reconnecting the airbag I'm still getting an airbag light on my instrument cluster. Is this a fault code that needs to be reset from the dealer? I know I plugged all the connectors correctly - only one way to do it.
View 1 RepliesPassat (B7) :: Rear Doors Bottom Warning Light Installation?
I have a kit of lights from my wrecked mk6 jetta for the rear bottom door lights that I would like to install on my Passat. I looked into the DIY thread for our cars and found nothing. I found some info on the Bold-Sport website but the connector at the window motor is different on the mk6 jetta compared to the Passat. My questions are:
1- Are the pins location the same to make them work on the Passat then it is for the Jetta?
2- Is the coding to activate them the same as the Jetta?
Golf IV R32 :: Low Temp Fan Switch Installation
Looking for a wiring diagram or instructions on how to install? I have the MK2 low temp switch with a piece of harness that I need to wire in.
Top is MK2 harness (red/black, red/green, solid red). Bottom is R32 harness (red/white, red/yellow, solid red).
Ford F-150 (2009-2014) :: Winch Mount Installation - Removal Of Plastic Molding?
Installed the Rough Country winch mount yesterday. One hour, by myself. Used a floor jack to lift it in place.
Only problem was removing the plastic molding which came in the spot the fairlead will be. Just a small rectangular plastic molding with a couple of bars down the middle for looks. It had two screws on top edge, and two pushpins on bottom , but also was molded with two catches on each side on the back I did not see. When I figured it out, and squeezed with just my fingers, little too hard and snapped one catch on each side. They slide into a slot and catch but wont be doing that ever again. Oh well.
As for mount, solid and easy to install. I used hand tools as the air gun would only hit one of the bolts for the front tow hooks. The other was blocked by plastic molding. No big deal.
Hidden Winch Mounting Plate for 09-14 Ford F-150 Pickup [1010] | Rough Country Suspension Systems.
Ford Fuel System :: 1994 F150 - Gas Tank Leaks - Removal And Installation
I just got a 1994 F150 with the 5.8L motor its a 4X4 with Auto trans. I have the dual tanks set up, midship and aft-axle and both tanks leak, more aft-axle then front. I was wondering how difficult is it to remove and install these tanks and what are some tricks to solve the problems I'll run into?
View 4 RepliesLexus ES 2007-12 :: 2010 ES350 - High Mount Third Brake Light Removal?
My wife's 2010 ES 350 third brake light has an intermittent LED issue. The last 3 LEDs on the pass side flash on/off when the brake is depressed. My understanding is there may be a broken solder joint. My problem is I can't seem to get the assembly out. How the high mount assembly is mounted and how to remove it?
View 2 Replies