Camry :: Cold Start Rough Idle Until Driven For About 2 Blocks
I have a 2003 Camry 4cylinder. On first start of the day the engine shakes a little untill it warms up and is driven for about 2 blocks. After that it is smooth. I cleaned what I could of the throttle body on the car, changed spark plugs and PCV. All that worked but cold start shake still there.
View 9 RepliesFord F-150 - 1997-2003 :: Rough Idle At Start For About 30 Seconds - Cylinder 1 Misfire
2000 5.4l lariat. My cylinder 1 for 2 years has been poping p0301code and has a rough idle at start for about 30 seconds. It also has a little white smoke for that 30seconds. new cop, new spark plug, new spark plug pig tail, swapped injectors to different cylinders multiple times to change code no luck. Compression dry and wet are at 200 and all cylinders are within10%. I had a dorman intake manifold installed 4 years ago and the code came a few years after. Im thinking intake manifold gasket is bad between cylinder 1 and the heater bypass tube allowing coolant to slowly leak down into the cylinder causing my rough start. I looked through the injector hole but could not tell. With all the info I have given is there any other places or things that it could be before I do a gasket replacement or is all my tests leading to the intake manifold gasket...
View 5 RepliesTiguan :: Running Rough During A Cold Start / Random Cylinder Misfires
I've got a 2009 Tiguan with 65k miles on it. A few weeks ago I noticed some issues with running rough during a cold start. I only noticed because the engine would vibrate considerably more than usually for the first few minutes of operation, and would idle at around 1050-1100rpm instead of the usual 750rpm. After warm up, things were fine. Suddenly the issue got bad real fast - wife was out and the MIL light came on, EPC light came on, and the car was running extremely rough. We managed to drive it home (2 miles) doing under 20 the whole time on side streets. Once I hooked it up to my OBD reader, I was seeing cylinder misfire codes on all four cylinders.. P0300, P0301..P0304, all five codes simultaneously.
Since the car was due for an oil change and hit 65k miles recently, I decided to throw new plugs in there to see if that would work. It did, at first.. A day or two it ran completely fine, no rough starts, no misfires, I thought I had solved the problem. The old plugs had some deposits on them and were original, so I thought I was in the clear. Two days later, same thing happened again.. EPC light, barely running and misfires on all four cylinders..
I read up some online and decided to order new ignition coils. Took a few days, but I got four new coils and threw them in. Again, problem solved it seemed. No more EPC light, misfire codes didn't come back and no more rough starts. I drove a good 40 miles with no problems at various speeds, but started noticing some misfires during acceleration (slightly rough acceleration, almost feels like a back and forth rocking motion, very slight). Sure enough, after a cold start I'm seeing the engine run a bit rough again with misfires. This time, only P0304 (misfire on cylinder 4) is thrown, and it only shows up as a "pending code" (engine light flashes for a few moments during start, but does not stay on).
I checked my connections, swapped the plugs and coils in what I thought were cylinders 3 and 4 (closer to the driver side), nothing. I swapped what I think are cylinder 1 and 2 (passenger side) just to be sure, but still nothing. At this point I'm pretty lost. I know enough to be dangerous with a carbureted engine, but am lacking in knowledge when it comes to a fuel injected turbo charged VW engine. It seems to be cylinder 4 misfiring consistently at this point according to the OBD reader.
Also of note.. I had some misfire problems last year, and had my intake manifold replaced as part of a recall (also had carbon deposits removed at the same time). Can a carbon build up occur this fast? Can it be the injectors?
Ford - Explorer :: 2003 - Misfire On Cylinder 8 / Running Rough At Idle And Under Load
126000kms on 03 explorer 4.6 truck started. Running rough at idle and under load.... Code came up for cyl 8 injector. Replaced injector... problem still there. Switched cop and plug with another cyl and plug.... same code and cycl 8 is definitely not working. Would a generic problem always affect i cylinder. I even checked wire clip on for injector... it appears ok. There is power to injector wire clip.
View 5 RepliesFord F-150 - 1997-2003 :: Skipping / Rough Idle And Loss Of Power - Misfire On Cylinder 4
Replaced the spark plugs and wires a couple months ago. Started skipping yesterday throwing the #4 misfire code so I replaced the coil pack, reset the check engine light but it's since came back on and has a rough idle and loss of power. By the way, it's a 97 F150 4.6L 4x4 with 200,000 miles.
View 4 RepliesCamry :: 1995 V6 - Rough Idle / Engine Lope When Started Cold
We have owned a 95 Camry V6 for 20 years and it has always been reliable. However, several days ago, the car started to have its first engine performance issue. When we start the engine cold, there was rough idle/engine lope. If it was warmed up for about 5-10 minutes, the car was fine for the entire day. but during this rough idle, the car jerked slightly as well if i press on the gas.
Since the symptom began, I took it to local shop A and they replaced all the spark plugs, pcv valve and air filter which did not solve the rough idle/looping problem. The rough idle continued, and few days later, I was unable to start the engine though it cranks. (at least that's what I think it does). Had it towed to shop B and they've replaced oil pump, which they thought to be the problem. I took it home, and the next morning I found myself unable to start the car.
Yaris/Scion & Vitz :: 2003 Echo Throwing A Cylinder Misfire Code / Idle Rough
My friend has a 2003 Toyota Echo that is throwing a cylinder misfire code. Original code is P0302 and P0302PD. The car is idling rougher, kind of sounds like "put-put-put". Also, the car has no power at all. He lives on a hill and he can't even pull out of his driveway. Lastly, the smell of the exhaust is gassy.
We have changed out the spark plugs...no change. Next, we bought a new ignition coil for the number two cylinder...no change. So, maybe its the wiring. Put the new coil onto the number 3 cylinder and the number 3 coil onto the 2 cylinder. Low and behold, the misfire code changes to P0303 and P0303PD.
Thinking we might have gotten a dud of a coil, we bought another. Same thing...new coil on 2 code is P0302...new coil on 3, code is P0303. Could we just have gotten two bad coils? Oh, coils were a BWD brand coil and Duralast brand. Should we just go OEM from dealer? OR Denso from Advance Auto?
Silverado :: 99 With 4.8 - Rough Idle And Hesitation On Cold Start Up
I have a 99 silverado with the 4.8 w/186k on the clock. I am having an issue with rough idle and hesitation on cold start up. Once the truck warms up the idle and hesitation go away. I have replaced the PCV valve hoping this fixed it, but it did not. I have also cleaned the TB and the MAF.
View 2 RepliesLeSabre :: 99 - Cold Start Rough Idle But Smooth Out
I have a 99 lesabre cold start rough idle but smooths out . Warm no start. Trouble codes P0171, P0300, P0336. Had plennum replaced 2 years ago but I'm seeing coolant around the base of the plennum so I'm going to have to do that again but I don't think that has anything to do with the warm no start.
View 14 RepliesTrailBlazer :: 2007 - Rough Idle When Start Up Cold
My 2007 TrailBlazer with 84K stumbles for 25 seconds when I start up cold. After 25 seconds I hear a click and then it runs perfect. No engine codes present. Have new plugs, new O2 sensor, new thermostat.
View 5 RepliesPassat (B6) :: Cold Start Delay / Rough Idle
I got the fuel pump and fuel pump control module replaced. Now I am still getting a cold start delay (5-10 seconds to start) and it has a rough idle sounding like its misfiring. This happened when i picked it up at the dealership after a new fuel pump BUT! keep in mind it has been doing this for a while so i figured it was the fuel pump.
New oem plugs and the coils were replaced when i bought the car because the coils failed during a test drive I need to scan the codes but i will post. Also this only happens during a cold start. if the car is warm and i go into target or something then start it shortly after its fine.
TSB'S I think will fix this. [URL] .....
Ford 6.0L Power Stroke Diesel :: 2003 F350 - Rough Idle / Cylinder 4 And 5 Contribution Balance Code
2003 f350 dually. Fully bulletproofed about 10k miles ago. Everything was running great for about 5k miles. A friend of mine got stuck and I went to pull him out. Got him out but got on it really hard...never overheated or anything.
Next day truck throws a cyLinder 5 contribution balance code. Ran ok but idled rough. Pulled injector and put a used one from a running truck in it. Code went away and runing fine for a few weeks. Took a long trip from FL to Texas, and on the way home same code occurred but idle was not as bad. I would clear the code and it would be fine for a few hundred miles, then would show up again. Made it home, still was driving around town a little with the code only showing sometimes. A couple blocks away from home taking off from a stop sign lost all power and motor shut off. Turned out the Injector o ring blew and hydrolocked the motor.
So now, ordered all new 155cc30% injectors , 58v ficm and new oem injector harness. Installed and Drove the truck to Illinois. After about 700 miles I noticed a little rough idle and had a cylinder 4 cont code. Made to Illinois and back to fl. At fl line I had cyld. 4 and 5 codes now. Cleared and cyld 4 was gone but 5 stayed. Got home and balance test showed 4 and 5 bad injectors. Sent them off to be fixed just got them back in. Truck started fine, smooth idle, ran for about 10 miles and cyld 5 code come back and so does the rough idle. I'm at a loss now.
Will be doing compression test tomorrow. Other than a rough idle truck runs flawless, will roast the tires and pull anything hooked to it. No hot starts, no symptoms of anything else. Possibly a problem with the oil rail feed on that cylinder? Main ficm harness? Bent pushrod?
Sierra :: 2000 - Rough Idle When Start During Cold Weather
2000 Sierra 1500, 5.3L engine. When he starts it in the cold (below 40 degrees) at first hits 1000rpm, then immediately drops to 400-500rpm. The idle is rough and wants to die if he tries to drive it. However after 10-15 minutes and the eng warms up, its fine no problems at all. There is no codes, so the scanner we had didn't tell us anything. He had cleaned the TB and intake system with cleaner, no dice. He also disconnected the IAC while it was idling rough, that didn't change the way it ran at all. We would like to toubleshoot it more before we start throwing parts at it.
View 1 RepliesSanta FE SM (2001-06) :: Cold Start Rough Idle For 20 To 30 Seconds
I'm having this cold start issue with my 2001 SF, but it doesn't seem to be fuel related like as the car starts fine but after about literally 1-2seconds the RPMs drop below 1k and the car will stall if I don't put my foot on the accelerator and keep it around 1000-2000 RPMs. But if I happen to make the revs go too high and let them drop again it seems like it wants to stall even easier. After about 30 seconds it smoothens out and drives almost perfectly except for a slight lack of power than normal going uphill (A.T drops to 2nd gear, sometimes 1st depending on the incline). We have had the coolant temp sensor and the fuel pressure sensor replaced. Could it be the MAF? We did clean it one time but it didn't seem to work much at all. Recently out of curiosity, I disconnected the MAF sensor and started the car it being started for a few days. No issue with idling whatsoever!.. ??
View 4 RepliesPassat (B5) :: 2003 VW GLS 1.8T - Rough Start / Idling And Misfiring On One Of Cylinder?
I haven't started my passat for the winter and I finally did today. It was ruff start/idling and I pretty sure it was misfiring on one of the cylinders. I turned off the car and start it again...same thing, ruff idling like 3 cylinders were running. I waited five 5 mins and started it again, then it was a normal start on all cylinders. But the engine light came on, even though it started properly. I know I have to clear the code to get rid of the engine light. But I want to avoid any future misfiring. So I'm thinking new spark plug/coil overs.
View 9 RepliesTouareg :: 2008 VR6 With Rough Idle On Cold Start / Puffing Noise
2008 VR6 Touareg with 71,000 miles. When he starts it cold the idle jumps around and is very rough. After 30 seconds or so it calms down, but you can tell it's still just not right. It also makes this puffing sound especially around the exhaust. At least puffing is how I'd describe it, maybe I can take a video of it at some point. No visible issues anywhere in the engine bay or anything that looks out of place. I ran an auto scan with VAG-COM and I pulled absolutely no faults. I found that puzzling.
View 2 RepliesFord F-150 (2004-2008) :: 2007 - Rough Idle During Cold Start?
My 07 F-150 5.4 has a rough idle during a cold start for about 1 minute. It happens mostly when the weather is chilly or cold. Also after the first start it doesn't do it the rest of the day. Of coarse they can't find anything wrong and tell me there are no updates for anything like that.
View 3 RepliesFord 6.0L Power Stroke Diesel :: Rough Idle That Accompanies The Cold Start
I have been debating if i should use seafoam engine treatment. My truck has been having issues with the first cold start of the day. I've noticed the rough idle that accompanies the cold start. I live in Denver so this truck sees alot of stop n go traffic. Will seafoam do anything about the dirty fuel injectors. They have to be replaced here soon but will adding seafoam solution buy me more time. If so, what are the steps on how to add. The can isn't very detailed on instructions and Internet isn't being useful. I have an 04 F250 Lariat Power Stroke 6.0L diesel
View 14 RepliesFord F-150 - 1997-2003 :: 2001 - Rough Idle In Cold Weather
Have a 2001 F150 FX4x4 and since the weather changed and started having days below 40 the truck has started running rough for about the first 15-20 miles. When you first start it starts like normal for first 3-5 min and then it starts loping real bad like it has a cam in it!
View 5 Replies