Santa FE SM (2001-06) :: 2004 - Timing Belt Broke And Turning On Ignition Switch Blows CPU Fuse
Son has a 2004 Hyundai Santa Fe 2.7 motor. The timing belt broke before we could replace it. Long story short, 24 valves, gaskets, timing belt, water pump, new belt tensioner and new pulleys. The motor is back together. The only problem is when you turn the ignition switch on, it blows the CPU fuse. The only electrical part we replaced was the purge valve.
View 3 RepliesMazda :: 1998 - Timing Belt Broke While Driving
1998 Mazda B2500. Timing belt broke while driving. How likely is it that my valves are warped & how do I fix it?
View 11 RepliesAccent MC (2006-11) :: Rebuilding A Motor Where The Timing Belt Broke While Idling
In the process of rebuilding a 2007 Accent where the timing belt broke while idling.
Pulled the head, ran a "water test" on the valves (put spark plug in, pour water on the valves and see if it comes out the exhaust/intake side) and found that only 2 intake valves were belt. Also shut off all the lights in a pitch black room, shined a flashlight in the intake/exhaust and didn't see any light leak from any of the cylinders except the one with the 2 bent valves.
Does this make sense? I would assume since 2 cylinders are always TDC at once, at least 4 valves would be bent.
Lastly, before rebuild I'll be replacing the 2 intake valves, all the valve stem seals, intake manifold gasket, exhaust manifold gasket, head gasket, head bolts and valve cover gasket. Anything else I should replace on the head? Trying to keep costs down as much as possible.
To add: Pistons have no damage on them, there are no marks of the valves hitting the pistons. The timing belt was replaced after it broke and the engine still ran however it ran rough. Compression test was done on only cylinder 1&2, 1 had 60 PSI and 2 had 0 PSI. Compression test was also done by just rotating the crank with a socket since I already had some of the engine disassembled.
Honda - Pilot :: Timing Belt Frayed Broke Due To Idle Tension Pulley Failure
I am working with Honda dealership management because I had my timing belt changed at 102,000 miles and 25,000 miles later The belt broke and frayed while driving in heavy traffic at night on freeway leaving me stranded in the median luckily instead of in the middle of the freeway. Honda dealership stating that the idle tension pulley caused the fraying of the belt not due to poor workmanship by their mechanics. I am asking dealership to consider assisting in payment because the day the belt went out, the car had been serviced for a oil change.
When I was called to be notified the job was complete I asked the service rep questions about the oil transmission and told him there was a noise in the engine could they check it or did they check it which she replied no that I would have to make another appointment for that. So even if I would've made appointment the next day the damage was already done because that night is when the belt broke Is this part of Hondas responsibility is it reasonable for them to take part responsibility. Also if the idol tension pulley had been changed at the same time of the belt, it would've saved my engine. So this is all my responsibility not theirs?
Passat (B5) :: 2001 - Timing Belt Correct Position?
I have a car Passat 2001 V6 and I need to know as changing the timing belt and the pump of water. Do I also need to know which the correct position of the timing belt is? As I know that this in the correct position and that the motor won't suffer damage. I wanted they could send me a diagram to see better as it is or that I use of reference to put it.
View 1 RepliesPassat (B5) :: 2001 - Changing Timing Belt / Testing Damaged Valves
So, I got a 01 b5 1.8 5spd given to me was broken timing belt. The car is super clean with 226k on it and had been well-taken care of..oil changes Mobil 1 and such. the owner just got his $$ worth and drove it till the belt went, slapping then towed it to my shop. It did not overheat and he was not driving it hard. Now here is my real question...apars lapping on a new belt and crossing my fingers, what testing can I do to check and see if there are any valves damaged? Can't I do a compression test w/out the valve train in time right? Also, if there does happen to be head damage. I would be in the market for an AUG head, unless it's just a valve that can be replaced....
View 6 RepliesPassat (B5) :: Oil Leak Around The Timing Belt
Over the summer my car started having oil drips under it and it ended up being the valve cover gasket, so I replaced it. I noticed the half circle gasket next to the cam chain tensioner gasket was missing, so I just jammed it in there (didn't have tools/time to get cam chain gasket replaced). Before I changed these gaskets, oil would drip on the back side of the motor (farther from the front). Today I noticed drips of oil in front of the engine. Looking around there is oil in the timing belt area and is dripping down from there. It doesn't look like the VC gasket is leaking.
My question, what would cause oil to drip into/from the TB area?
engine = 1.8t ATW longitude
Passat (B5) :: Timing Belt Replacement?
I am looking for a link or instructions on replacing the timing belt on a 2.8 30V. I attempted to search and mostly came up w/ the info relating to the turbo.
View 2 RepliesPassat (B5) :: 1999 - Timing Belt Should Be Done At 100 K?
hile since i've posted on the Tex. I've got a buddy who's looking at getting a 99 Passater, the car has 110k miles on it and it's the 1.8T. I've been reading a few posts out there about what to look for on these cars and of course maintenance records are at the top of that list. The other things I've been reading about is timing belt (I'm assuming this costs a few dollars to fix) probably should be done at 100k, and some front end suspension parts seem to go bad at an early interval. Anything else that we should look at on this car? It's an AutoTranny, I know the B4's had a horrible AT, I used to own one. Did they fix this pretty well in the B5's?
View 4 RepliesElantra XD (2001-06) :: Timing Belt Replaced Now Car Won't Crank Over
Changed the timing belt. Used the red mark up top and the cut in the block on the lower one to get TDC. Changed everything with new parts. Double checked the marks after the belts were on (rotated by hand through two full turns and checked to see if the marks were in the same spot). I followed the write up that was posted here by U95.
Anyway, the car won't start. It tries cranking, but won't actually start. There is fuel and the battery should be good to go. There shouldn't be any Fuel/Compression/Air issues.
I guess my question is: If the timing belt is not tightened enough, would that keep it from firing?
Also, in trying to crank it by key every thing sounds normal (no knocks or pings or valves getting bent sounds) and turning by hand gives just the little bit or normal resistance but spins nicely.
I'll probably take the battery to get it load (I used my tender to try and start it as well, didn't make a difference) tested tomorrow and then try the starter (shouldn't be bad though, only 60k on the car). Otherwise I'll have to teardown and start over.
Passat (B5) :: Car Died After Changing The Timing Belt
OK, so yesterday I changed my timing belt and all new components. I started the car before completely reassembling everything (bumpers, etc.) and it ran a little rough at first, then smoothed out. But this only lasted a few seconds and then it died out. I thought not much about it and finished my reassembly. Afterwards, the car would crank and crank and finally start. However, it would never idle smooth and it stalled out only after 1-2 seconds.
I did some investigation, and found the plugs all had wet oil on them. Changed them out and tried to start car with same results. Looked again at the plugs and they weren't as oily, but on their way. I looked all over for a source of this problem and found a broken "pipe" on the passenger side of the engine. It is black and sits behind a heat shield, directly under a larger black pipe. They both run from front to back. I think the broken one might be a vacuum line of some type, although when I plug it, nothing happens.
My fear is that I botched the timing belt job and subsequently, bent a mess of valves. But, I'm holding out hope for another cause of this dilemma. What is the smaller black tube/pipe on the side of the intake? The broken piece comes off a 90 degree elbow pointing to the ground. I'm guessing it was broken before the timing belt job, but who knows? Perhaps I broke it when I moved the radiator into service mode. Could it be part of the turbo? I thought that might cause the rough idle and stalling.
Oh, one other thing. When I last tried to start the car, I got a flashing "STOP" on the instrument panel, followed by something about the oil. The oil words only appeared for a split second before going away. Not even long enough for me to read the whole sentence.
Passat (B5) :: Keeps Stalling After Timing Belt Replaced
99 passat 1.8t with 5spd has 95k on it. 2 weeks ago my ex wifes car broke the timing belt and bent 12 valves so brought it to mechanics to get repaired and got it back seems to start up fine but when shes driving it stalls out on her. Mechanic says its something do with electronic throttle and nothing to do with his work. No check engine codes yet anyways .
View 1 RepliesPassat (B5) :: At What Mileage Need To Replace Timing Belt?
I was just curious and bored this morning. So I wanted to ask you all what mileage did you replace your timing belt at?
View 24 RepliesPassat (B5) :: Timing Belt Replacement After 105,000 Mile?
My 2004 Passat 1.8T GLS (station wagon) has 72,000 miles. I checked the manual which says that timing belt is to be replaced at 105,000 miles.
However, car is 8 years old - does the age matter or I should be fine until I get to 105,000 miles to replace the timing belt, tensioner, water pump etc.
Passat (B5) :: Timing Belt Replacement For 2.8 V6 Engine
I got 123000 km on my car. Manual says 144000 km is the right mileage to replace the belt, but I have heard opinions that it should be done earlier.
View 7 RepliesPassat (B5) :: 2000 - Changing Timing Belt?
I got 102k on my 2000 1.8T Passat, ATW engine code. I'm thinking about changing the timing belt. Is there any way to check if it was done before. How to recognize factory timing belt?
View 9 RepliesPassat (B5) :: Timing Belt Won't Working - How To Replace It
Of those out there whose Timing Belts HAVE failed , at what mileage have they gone bad and what damage was done?. This would be good to know to give an idea as to when to replace the Timing Belt.
View 12 RepliesPassat (B5) :: Timing Belt Replacement Every 60,000 Miles?
I was told that I must replace the timing belt every sixty thousand miles. Is this true?
View 24 RepliesElantra XD (2001-06) :: Timing Belt Tightness And Whining Sound
I recently replaced the timing belt, tensioner, and roller in my car. Today I became concerned that I hadn't tightened the tensioner properly so I did a quick check (it was). I also noticed the timing belt felt a bit loose, so I tightened it to what I thought was about 1/4" deflection with 5lbs pressure—not what that feels like in that tight space.
When I started the car there was a noticeable whining sound. Before I changed the belt there was a slight whining sound (but there was no whine after I changed the belt). So I loosened the belt a bit and there's now a slight whine. I feel like the whine shouldn't be there but it's hard for me to imagine that the belt should be any looser since I can move it 1/4" inch without much effort.
So, should I be tightening the belt to the point where the whining is gone, or is a slight whine ok?