Accent LC (2000-05) :: Rough Idle - Engine Get Louder And Car Starts To Vibrate Slightly
Recently bought a 2001 Accent that has been experiencing a 'rough idle' for the last few weeks. Basically, after I've driven the car for a few minutes (from a cold engine position) and then stop at a stop light or stop sign, I can hear the engine get louder and the car starts to vibrate slightly, after I've driven for about 15 minutes at higher speeds and then stop again I can actually see the steering wheel shaking when I take my hands off of it. If i put the car in park when I am stopped and the engine is on, the idle calms down quite a bit. The weird part is that when I first start driving the car in the morning, the rough idle problem doesn't happen until about 5 minutes of steady driving - so when the engine is colder I don't experience the problem, The problem is not that serious, and Ive already brought it into a dealer who cleaned out fuel injection, gave me a major tune up and replaced all the spark plugs, but the problem still persists. I am gonna bring it back to them but they seem a bit lost to be honest. Other than this the car is driving normally when I am not idling.
View 14 RepliesFord F-150 (2009-2014) :: 2011 XLT - Idle Slightly Rough In Drive / Stall At Stop
I have a 2011 XLT 5.0 V8 with 133,260 miles. I have extended warranty for the next 12,000 miles...which is great because I drive about 400 miles a month... Anyhow it runs great but for one small issue (hopefully) that has been intermittent.
She likes to idle slightly rough in drive at a stop or very low speed, and in reverse at slow speed. If I don't maintain the RPM it will stall and the low oil pressure light will come on, which I imagine comes on because of the sudden stall.
I first noticed this while backing into my garage in the driveway, It would fluctuate in RPMs and if I didn't maintain the gas it would shut off. I took it to the dealer and all they were able to tell me was the Tranny fluid was low and it would cause it to shut off at incline because a sensor isn't detecting fluid in the tranny. I thought this was weird but being as I have never owned an F150, I didn't know better.
It was fine for a little over a month and it started doing it again at stop lights and backing into my driveway. It has become frequent but there is no issue driving at speed and on the freeway. There is no stuttering or shaking and if it weren't for the fluctuating RPM at a stop and the stalling, it would be hard to tell if there was an issue.
All I can note is that there is a clicking sound under the hood, if I remember correctly the last time this happened I was at a 1/4 tank of fuel like I am now, I also feel like it may be a throttle body issue, or some sort of air sensor, I plan on taking it to the dealer but I figure I would get a more informed answer on the forums.
I also hear this is a common issue with the 5.0s... I purchased the truck in December and since then I have only put 250 miles on it.
Ford 7.3L Power Stroke (1999-2003) :: 2002 F250 Starts And Runs With Rough Idle For About 10 Seconds When Cold
I have an issue with my 7.3.... the truck will not start if it sits overnight without being plugged in, even in 65 degree weather. It starts and runs with a rough idle for about 10 seconds after its been plugged in for an hour, after the rough idle is gone it runs great .. it will Stat back up as long as the truck is warm (70+).... I've replaced the batteries, glow plugs, starter (it was going bad) and fuel filter. .. also replaced the gpr today. ....
View 14 RepliesLexus IS 2014+ :: Car Is A Bit Rough When Engine Is Cold
The tranny is a bit rough when the engine is cold. I understand cars run differently when they are cold (I'm not disputing that) but my prev 2IS' tranny use to be much smoother when running cold. I took my car to a dealer, made them keep it overnight and test when cold. They said the car is operating normal and the master tech didn't notice anything out of the norm. The car is jerky on the daily so it's not an isolated incident.
View 10 RepliesLexus GS 2013+ :: 2014 - At Cold Rough Shifting
I have 3,500 miles on my RWD '14 F Sport. I have been noticing since its been getting colder, that the transmission is jerky for about the first 5 miles of my morning drive. It's like that even if I let my car warm up for a minute, instead of just taking off right when I start it. It's a lot more hesitant to downshift one gear for an incline. And when it does, it's slow, sloppy and then clunks.
View 14 RepliesLexus GX 2010+ :: 2014 - Nasty Rattling Near Idle / When Cold
So this is the second winter I've had my GX (a 2014 purchased in Nov. 2013).
With radio and other accessories turned off, there is a rattling/grating sound that is quite pronounced at/near idle, especially when cold. Sounds like a rapid PRAPP-PRAPP-PRAPP. This occurs when the vehicle is in Drive, but stopped. Occurs most often at within the first 5 minutes of operation....i.e. leaving the house or office, driving to the end of the street, hearing it at a stoplight or stopsign.
I've posted videos/recordings of it previously, which I have also shown to the dealer. The dealer said they could sort of reproduce, but could not diagnose it. I have tried to crane myself outside of the GX to listen to it, but from outside nothing seems to be amiss.
At first I was worried that it was engine knock/the car eating itself, but if that noise was representative of that, I think the car would be blowing smoke or dead by now. I have not noticed smoke, adverse effect on fuel economy or the noise at speed/under load, as you would expect if the engine were truly knocking. So I'm thinking it may be a fan, some type of underhood accessory, etc. that is the culprit. Sounds almost like a plastic component (fan, pulley, etc.) could be off kilter?? Something that more or less goes away after the engine has fully warmed up and the car has been driven for 10 mins or so.
Camry :: 2002 - Car Rough-ish Idle And Jerks Slightly In Low RPM
I changed all of the brakes on her car yesterday, test drove it, everything was great. Put close to 100 miles on it w/ no issues. Therefore, I don't think it's anything I did.on her way to work, the CEL came on. The car has a rough-ish idle, and jerks slightly in low RPM. I went to Pep Boys and got it read. it threw 8 codes:
P0171
P1130
P0300
P0301
P0303
P0305
P0442
From what i've read, the p0171 is the system is running too lean and p0442 is a leak somewhere. The 300s are cyl misfires.I don't want to go replacing every conceivable part. What these codes mean in conjunction?
Elantra GD (2013+) :: Slightly Rough Idle During The First Few Miles
I have a 14 GT base with manual and I've been noticing at idle (sitting at stop lights...foot on or off brake and or clutch...in or out of gear) it has a bit of a rough idle or stumble during the first mile or two...then its fine. It doesn't feel like it will stall and if I tap the gas I do not notice any difference in throttle response. RPM needle stays steady... is the just something that is normal? It doesn't bother me a lot... just noticeable. All that aside, except the occasional lifter noise at cold start (not always...which is odd) all is good.
View 6 RepliesGolf/GTI VI :: Rough Idle / Slightly Misfire / Burning Oil
This is my first new car, but I am assuming the idle should be pretty smooth. I feel my idle and it feels sort of rough. Almost like there is a slight misfire but not that intense.
One more question, car burning oil?
@ 7500 miles I was down a little more than a quart and now @ 14,100 I am down almost a quart. That is slightly alarming.
Elantra MD (2010-15) :: Slightly Rough Idle At Stop Lights
My 2011 Elantra has a slightly rough idle at stop lights. It doesn't happen ever time, and some people probably wouldn't even notice it, but at every few/several stops it idles a bit rough. When I recently had it in to Hyundai service for the ECM update, I asked them to take a look at it. Of course, they couldn't replicate it at the time, so they couldn't do anything to address it directly. The service manager asked if it happens when the A/C is on or off. While I didn't know the answer at the time, it seems to happen with it both on or off. He did say that the ECM update may address/fix the issue, but unfortunately it didn't. While it's not a big problem, it's a minor annoyance I'd like to get fixed (as I need to enjoy my ride at all times.
View 220 RepliesLincoln - Towncar :: Slightly Rough Idle When Started Up And Let It Sit In Driveway
I have a 1998 Lincoln Town Car with about 350,000 miles on it. This morning I sensed a slightly rough idle when I started it up and let it sit in the driveway. While idling I plugged in a scan tool and after a few minutes it showed a P0306, a misfire in cylinder 6. I know there could be a few causes of this but my past experience has been a bad ignition coil (this car has the coils on each plug).
Over the years I've had 3 coils go bad, all giving the same rough idle symptom and P030x, where x was the cylinder number. Replacing the coils solved the problem each time.
So this morning I assumed it would probably be the same. On my way to the auto parts store (4 miles), I monitored the computer, it kept throwing a P0306 (cylinder 6) and I kept clearing the code. About 2 blocks from the store, the car seemed to be running a bit rougher. When I pulled into the lot, I got a P0307 code (and no P0306). Hmm. Well, I bought a new coil and replaced coil 6. I then sat in the lot and idled it and after a few minutes it threw the P0307 again. I cleared it a few times and it came back.
I assumed there was about 0 chance that a second coil could go out within minutes of another (assumption from a car tinkerer, not a professional), so rather than buying another coil, I drove it home to do some further testing. On the way home, it kept throwing the P0307 and nothing about P0306.
So at home, I swapped coil 7 and 5, idled it for a few minutes, and, sure enough, it threw a P0305 (the problem had moved to cylinder 5, following the coil). This indicates to me that I had 2 bad coils?!?
So my question is whether it's possible, or even common, to lose two coils at virtually the same time. I should also point out that before today I did not notice rough idling and there were no computer codes set. I also thought maybe it's possibly a problem developing with an ignition module (but I'm not sure if my car even has one).
Anyway, it was late and I have not replaced the second coil. I did do a couple other tests. I measured the resistance on the primary of the new coil, as well as 5, 6, and 7 coils. They were all close to 0 ohms. The resistance of the secondary ranged between 5k and 8k depending on the coil. Out of curiosity, I also did a final swap of the original coil 6 with the "faulty" coil 7 now in 5 (follow me?) and it still throws a P0305, indicating both the old 6 and old 7 coils are, indeed bad. Another note is that both "bad" coils are about the same age (maybe 150k-200k miles on each), so they're not newer ones.
Does this all make sense? Should I go ahead and replace the other coil and see what happens, or should I check something else?
Ford - Mountaineer :: 1998 V8 5.0 - Shaking At 40 MPH / Slightly Rough At Idle
A couple of days ago (Friday, Sept 14th), I noticed my 98 V8 5.0 liter Mountaineer was idling rough. I had the codes pulled and got P1401, P0455 and P0308. I did find a vacuum leak and fixed it (changed the air filter and cleaned the MAF while I was in there). I also replaced all the plugs (based on the P0308 misfire). I cleared the codes after that with a neg battery pull.
I'm still running slightly rough at idle, but not as bad. However, I have found that when I get up to about 45MPH (1500 RPMs) I started to get a worrisome shaking/ vibration. It's difficult to tell where it is coming from. If I let off the gas, or give it more and go up to about 50 mph, the shaking stops. It is only when I'm pressing the pedal in this range (like it is having trouble switching gears, perhaps?). Over the past two days of driving it and testing, I have been to autozone and had the codes checked. Nothing comes up, and no CEL.
I just had a new trans put on about 6 months ago. The only thing that preceded this issue was I got an oil change the day before this started at a place I don't normally go to (unlikely, but since they didn't write the type of oil they used on my window tag, I figured I'd mention it). I've read some suggest it to be a tire issue; but that strokes me as odd, since the shaking only happens when applying gas.
Buick - Parkavenue :: 1995 - Occasional Miss When Cruising Along At Highway Speeds And Slightly Rough Idle
Got a strange one here. 1995 Buick Park Avenue, supercharged 3800, 159K miles... an older car, but an unmolested one. A little over a week ago I began to notice an occasional miss when cruising along at highway speeds, along with a slightly rougher idle. Both the fuel filter and the plugs/wires predated my ownership of the car (a little more than 6 months); so seeing no obvious culprit, I replaced them and hoped for improvement.
Unfortunately, neither had any impact. The missing continued to become more noticeable. It was never present under acceleration. Most of it was like a split-second long version of "bucking" that could be observed while cruising at lower (<2000) RPMs. It was also very noticeable at idle. Eventually a code was set: P0341, camshaft sensor issue. If the story had ended there, it would have been just another night in the garage. But it didn't.
As I was noticing the aforementioned symptom increase, I also noticed my voltmeter would occasionally "twitch" in the downward direction. Eventually I had an incident where I came to a stoplight... transmission in Drive, foot on brake, gauge dropped to around 10-11v. It returned to 14v momentarily, but dropped back down, held there for several seconds, returned, etc. No particular rhyme or rhythm. Of course my first guess was that the alternator was failing; a separate problem from the other.
I checked all the relevant connections (at the battery, at the alternator, etc), and cleaned them for good measure. All were tight, relatively clean, and the cables showed no resistance on the ohmmeter. It happened that I had another correct alternator on hand (used/working pull), so I swapped it in. No change. I reinstalled the original and was back where I started.
On my most recent drive, I noticed both issues had become very noticeable. The drop in voltage was happening at nearly every stop, and the missing was happening a few times per minute while coasting along. There seemed to be some correlation between the missing and voltage fluctuating, but it wasn't absolute.
I decided to attack the voltage issue again. Re-checked all the cables; same result as before (all OK). Looked all over the car for possible bad grounds, loose connections, or other visible problems, but found none. My next thought was to run a jumper from B+ to the voltage regulator's Sense input (have seen issues there on more than a few older vehicles) - but after reading that this car uses the PCM as the voltage regulator, I didn't proceed.
Just to be certain I'm going to have the alternator tested by the local auto parts store. But I suspect it'll pass.
Bmw - X3 :: When Cold Outside Car Starts And Idles Rough Until It Gets To Temperature
The problem I have is when it is cold out under 40 degrees, my car starts rough and idles rough until it gets to temperature. My research has concluded it may be cold start. Does this sound right?
View 5 RepliesBuick - Regal :: Rough Idles And Misfires On Cold Starts
1991 Regal, 3800 v6.
So here's an interesting observation. When i turn the ignition to ON, I hear no sound nor feel any vibration from the fuel pump. Is there any scenario where a fuel pump fails to prime yet kicks into gear after a start? So, I've got rough idles and misfires on cold starts. Before I start replacing parts my diagnostic plans is as follows:
Remove and inspect spark plugs.
Inspect and test starter coil/distributor (still have to research how to do this)
Test resistance on fuel injectors.
Test pressure drop on fuel rails.
Test compression for possible small head leak.
I'm wondering, if I do have a tiny head leak that is letting in a drip or two of coolant after hours of the engine sitting, will I be able to see this on the gauge doing a compression test? I've never done one before and still need to buy a gauge, but maybe I'm better off just doing the other tests and if they all check out I can be certain it is a minor head leak.
My assumption is that I have a leaking injector; just trying to do things the proper way.
Golf/GTI VI :: 2012 - Starts / Rough Idle Then Dies
I bought a 2012 GTI with 6-speed manual two weeks ago. It has ~42k miles and it has been running great for the past 2 weeks until tonight. Went with my wife and son to the store and then the problems started. We got in the car to leave, it started fine, but died suddenly a few seconds later at idle when we were trying to get my son buckled in. I thought maybe I did something odd and it was me, so I turned the key off and tried to start again. It was a rough start(took a second) then idled roughly under 1k rpm and died shortly after. I tried one more time, same thing. There were no CELs at all, just the battery light after it died like normal.
At this point I'm thinking it may be that the timing chain tensioner gave out and that's the problem, so I decide to get a ride back to the house for my laptop and Vag-Com before trying to start or run it anymore. I get a ride, grab those, and head back to the car. When I get back in the car I realized my laptop battery was dead, so I decided to try to start it one more time. This time is starts just fine and I'm able to drive home without any trouble at all. No hick-ups, no stalls, no low-idle or anything. I was able to run the Vag-Com Auto Scan on my other laptop at the house and will have the readout below.
The only code thrown was on the immobilizer at 69157km which would have been when I had a replacement key cut and coded at the dealership I bought it from(a local VW dealer). I ran this scan with the key on but engine off and after realizing it wasn't giving me any codes at all I decided to run the scan with the engine running. Well, when I tried to start the car to run the scan, it died on me at idle again. So I left the key on(after the car died) and ran the scan and got the same results as below. I was then again able to start the car and drive it around the block and then park with it idling without any problems at all.
I don't understand this at all. The car has been running perfectly until now for as long as I've had it. I just changed the oil and filter this past weekend for Mobil 1 0w50 and OEM filter. And I've only run 93 octane in it, which it currently has a 7/8 full tank. I'll be calling/going by the dealership tomorrow to try and sort this out.
- I just ran VCDS data logging on the fuel system while trying to start my car just now (after sitting for ~30 minutes)
- While running I watched 106 Fuel Rail Pressure - Actual drop from ~40bar down to 6.5bar
- I was able to tap the accelerator peddle and it jumped back up to ~40bar
- After evening back out and not stalling again, I ran Autoscan and came up with:
000135 - Fuel Rail/System Pressure
P0087 - 000 - Too Low - Intermittent
I went ahead and ordered a new fuel pump and seal and received them this afternoon. I've already replaced the pump and have driven around a good bit this afternoon to test things. One of the big things I've noticed is that even though I still have the rear seat bottom out of the car, I can barely hear the new pump, where as the old one was noticeable. I'll update again if I run into any other issues.
Elantra MD (2010-15) :: 2014 - Tapping / Clicking Sound On Cold Starts
So my 2014 Elantra makes a tapping/ticking sound on cold starts which stays audible after the oil gets up to temp for at least until about 10 minutes of driving. I've heard this noise since I bought the car and of course kept searching all over the forums but everyone seems to have a different opinion as to what causes it and if it's normal or not. I finally decided to drop my car off at the dealer overnight so they could start in the morning and diagnose it. They listened, ran some tests on the engine and said everything was fine, nothing was damaged and that the sound is from the second fuel pump that is located over the engine.
They tested my fuel and said it's making the sound because I'm using a heavy fuel quality, then the tech told me I should run a fuel cleaner every other time I fill the car up. This seems excessive to me? I only fill my car up with Shell gas and avoid discount places which the tech agreed that Shell gas should be fine. I only have 22k miles on the car do I really need to be running cleaners every other tank of gas? Also wondering if using non ethanol gas would fix this problem. I did run 1 tank of non-ethanol but didn't notice a difference and since non-ethanol costs more than premium I went back to regular. I will try a fuel cleaner though?
Tiguan :: Starts To Idle Very Rough And Seems To Stall - Rear Main Seal Failure?
So about 2k miles ago I went to start my tiguan (cold start) and it starts to idle very rough, barely keeps itself from stalling so I take it to the dealer the next day and they tell me the car needs carbon cleaning and a rear main seal and wanted about $2500 to do all this. I declined the service since it was a lot of money to just drop then and there. I am wondering/worried there are other issues along with the rear seal leaking or if its just something else causing the issue. I looked under the car and most of the bottom of the motor is soaked in oil. I have not done the auto trans service on the car and was wondering if that could have had anything to do with the leak. The other thing about it is once the car gets up to temp it runs totally fine. AND once in a while it will start up fine, no rough idle. That probably happens about 20% of the time (I do at least 4 starts throughout the day). The car current has 92k miles on it. What it could be/what I should do?
View 10 RepliesFord Ranger / B-Series :: Rough Idle - Check Engine Light Starts Flashing
My 3.0 with 216k miles has developed a rough idle and it progressively got better with new parts and cleanings. On startup it revs up to 2k then back down to 600. If I let it idle for about 8 or so minutes my Check Engine Light starts flashing. If I drive about for a little bit it stops and is just fine.
While the light is flashing I get codes P1000, P0305, P0306, and P0316. Which are OBDII Monitor Testing Not Complete, Misfire detected in Cyl 5, Misfire detected in Cyl 6 and Engine Misfire Detected on Startup (First 1000 Revolutions) respectively. Any other time the truck runs like a dream. Gets 20 city and 29.5 highway.
I cleaned my Mass Air Flow, replaced my Idle Air Control, SeaFoamed throttle body and vacuum lines, brand new coil pack, new wires, new plugs, new fuel filter, I've only ever run 91 octane, Chevron with Techron goes in at every oil change and B12 every other and I just ran 3 bottles of Lucas fuel injector cleaner.