Lexus RX 2004-09 :: Grinding Sensation And Pulsation On Applying Brakes
I have 04 rx330 with 70 k miles. Lately I started to feel grinding sensation and pulsation on applying the brakes initially it is fine then it will be felt specially when the car comes to near stop
A mechanic looked at it and said bad rotor I replaced with new rotors and pads still doing the same thing, as I inspected the old rotors and pads there was no visible defects.
Ford Brakes/Suspension :: Brakes Does Not Feel Soft / Truck Is Hard To Stop
I have this truck (in signature below) that I have not driven for ~3 years. As I am starting to drive it I am noticing I need to put A LOT of pressure on my brake pedal to get the brakes to work. They stop the truck and the pedal doesn't feel soft as if there is air in the line but it feels as if I apply a lot of pressure and there isn't a lot of grab.
While it might be possible, I don't think I have any type of glaze or coating on my brakes that would cause this. 95% of those 3 years, the truck was inside.
I wonder if it feels as if the truck is hard to stop because of the additional power I have coming from this new motor?
Is there any type of part I can replace in the brake booster to adjust the pedal? Or brake booster. Maybe that is going bad?
Honda - Odyssey :: 2007 - Brakes Are Soft And Have To Press Hard?
I have a 2007 Odyssey. Honda already recalled it once for brake issues. It has 44000 miles and we already changed brake pads once. Now again beakes are filling soft and have to press hard. what should I do?
View 3 RepliesFord F-150 - 1997-2003 :: Brakes Hard When Motor Off Soft When On
My son just bought a 97 F150 with the back brakes blocked off. The front brakes had about full pedal when the was on. We changed the front calipers and brake pads. Bled them came back with great brakes (with back brakes blocked).
Then we found out the back calipers was none so we bought all new parts for both back brakes, found some leaks in the rear lines fixed them. Now we bled the brakes with the motor off till no air came out. Solid pedal. Then turned on the motor and the pedal goes down 3/4 of the way now easy.
Stops on snow good no tire sliding. Turn off the motor has solid pedal again.
Lexus RX 2004-09 :: Pulsation While Braking Sometimes When Going Over 45mph
What could cause this? Its coming from the rear end. It seems to happen if I am going over 45mph and apply the brakes. It feels like a warped rotor, but if braking from 40mph and below, it is smooth. Both rear wheel bearings have been replaced. Tires are new. There was a vibration while cruising between 40&50mph, which was "cured" by the new tires... While replacing the wheel bearing, I noticed some play in the right rear axle at the joint closest to the wheel.
View 11 RepliesCamry :: 2004 - Brakes Are Very Soft
I own a 2004 camry 3.0 v6 Car. Recently, i realized that i have to press hard on the brakes for the car to stop and its been like that ever since. I driven my dads rav4 and my friends corolla to test and their cars begin to stop just as i light press on the brakes. Mine however, i need more force to being to slow the car down.
View 14 RepliesDodge - Journey :: 2010 - Pulsation From The Brakes
I have a 2010 Dodge Journey which my husband and I purchased a year ago used. Over the course of the year we have been dealing with brake problems. No less than a week after we purchased it, we had it at the dealer for pulsation from the brakes and they turned the front rotors. Still didn't resolve the problem completely and was back again and they turned the rear rotors . 4 months later we're back with the pulsation and I had my front rotors turned again. Wasn't quite happy with that as I still felt the pulsation just not as bad. We decided to just let them be and wait.
Well the pulsation got worse over time and a month ago went to Pep Boys and they replaced my Front pads and rotors, they inspected all four prior to that and told me they all looked fine. But I insisted that the pulsation was pretty bad that even felt it on the steering wheel. They replaced the front ones. Next day I was back because the pulsation was still there, and they machined the rotors incase they were already defective. So long story short what else can be causing this. My tie rod ends do not look to be severely worn to possibly cause this. Getting really tired of this car and all its little quirks and problems honestly.
Ford Brakes/Suspension :: After Pressing Pedal Resistance Became Really Soft And Brakes Very Sensitive
I have a 2004 Ford Expedition and today on the freeway I had to step on the brakes pretty hard to avoid an accident. After pressing, the pedal resistance became really soft and the brakes worked, but were very sensitive (a lot of pedal movement to brake). I had this happen some time ago and I did a complete system flush and no problems since then, but it has to do with how hard I hit the brakes. What could be wrong????? BTW - I never noticed the anti-lock brake pedal pulse at all during this event. I'm not even sure it is working at this point. No dash lights to indicate an error of any sort.
View 3 RepliesPrius (2001-03) :: Brakes Are Soft And Can't Remove Key
Bought a prius off craigslist that didn't have a hybrid battery. Replaced it with a used reinvolt battery off ebay. Car starts right up now. However, there's a few things wrong with it. I can't get the key out of the ignition and the brakes are soft. Could these be related?
I have a fully charged and known good 12v battery in the car. And when I remove it, the key comes right out. If I bleed the brakes, do you think that will solve the problem?
Chevrolet :: 1996 - Soft And Spongy Brakes
A while ago I had to lock up my brakes to prevent an accident. now my brakes are soft and spongy, going all the way to the floor and still not quite stopping. making abs type noise. also, i can press all the way down while standing still, with the same type noise.
1996 chevrolet astrovan
7 Series :: 83 733i - Soft Brakes (Pedal Right To The Floor)
The pedal used to go right down to the floor and would barely stop the car from a crawl, in response I have bled the brake lines to all calipers, and checked the hydro booster fluid level, and with only slight improvement the pedal almost hits the floor.
I am thinking the brake master cylinder is shot. The pedal becomes solid after about 15 pumps when off, and holds pressure, when on it takes several pumps to build any sort of pressure and cannot be built up to the solid point, and looses pressure quickly when just holding the pedal down.
Santa FE SM (2001-06) :: Brakes Pedal So Soft That It Goes To The Floor
I have a Hyundai Santa Fe 2005 2.7L 4WD ABS.
The problem is that the Brakes pedal is so soft, that it goes to the floor, and doesn't brake at all in first pedaling. I am able to apply brakes after pumping the pedal thrice in continuation and then when it builds up some pressure, then it brakes and I'm able to stop the car. Once, I take the foot out of the pedal, it goes bad again. Once, again if I have to apply brakes, I have to do 3-4 times pedaling.
The brakes are stopping the car fine when they get applied in 3rd or 4th pedaling and when pressure is built up. Its the pressure not getting built up or maintained in the first go.
What has been done by the mechanics to solve this:
1. Master Cylinder has been replaced with a new one. (This has been done twice)
2. Brake Pads have been changed.
3. Brake fluid has been replaced and is upto the brim in cylinder reservoir.
Ford - Taurus :: Brakes Bled - Still Soft Pedal - No Leak
I changed front rotors and bled brakes. They were hard for a few days and went soft. No leak in fluid (MC reservoir is still full). No leak in fluid near any wheel. Could I need to bench bleed the master cylinder?
View 12 RepliesDodge - Caravan :: Soft Brakes In Spite Of New Master Cylinder
Lost braking power. Replaced master cylinder. Brakes went soft again. Shop says it is something to do with the ABS Control Unit (?). Took it to dealer who said it is a leaking master cylinder. Back to shop which claims nothing wrong with new master cylinder and it i the ABS blah blah. Dealer says it can't be ABS. Went to another shop. Replaced master cylinder again. Brakes still soft. No one can figure this out and I am stuck with very soft brakes.
View 5 RepliesFord - Fusion :: 2007 - Brakes Stay Soft After ABS Engages
I have a 2007 Ford Fusion (I4). Recently the brake pedal goes extremely soft after the anti-lock brake system engages. It can still brake, but I have to press the pedal almost to touching the floor. It will stay soft a while (at least 20 min, probably longer), but I found that if I pump them hard a few times (like while at a red light) it then returns to normal.
My mechanic can't figure out why it doesn't immediately return to normal after the ABS engages, and he's not sure what to replace to fix it. I don't have the cash right now to just go replacing lots of stuff, hoping it might work.
(He even mentioned the possibility of removing the ABS fuse to prevent the ABS from kicking in and triggering the problem. Though wouldn't that be a step backward, safety-wise? I always heard that ABS is much more effective than pumping brakes manually...)
What's causing this and how to fix it?
Nissan - Rogue :: 2019 - Brakes Feel Spongy / Soft
My 2010 SL rogue's brakes seem to be extremely spongy/floaty. When stopping I need to push the brakes pedal all the way down before it'll come to a complete stop. It feels like I'm pushing air out. Just got her back from bthe repair shop, and had been driving a rent a car(2015 Ford focus) and the difference between the braking is night/day.
Checked the brakes fluid and its just a hair under max line. Was under the impression that the break pads were replaced a year ago. Best obvious answer I can figure out(google) is possibly air in the brake lines?
GTI 337/20th Anniversary :: Clutch Pedal Goes From Being Soft To Very Hard When Close To Disengaging
I have an Imola 20th and recently i have been having some problems with my clutch. The pedal goes from being soft to very hard when its close to disengaging. It also engages very heavily when I go to let it out. This only started happening recently when temperatures started to drop if this has any effect on a clutch. Also, I replaced a shift fork two months ago and was curious if there was possibly anything going on with seals around the slave cylinder.
View 2 RepliesSubaru - Impreza :: 1999 - Soft And Pulsing Brakes / Now One Brake Line Blown
I have a 1999 Subaru Impreza Wagon that I have owned for about 2.5 years, and I love it. I travel for work and I use rental cars alot. I have noticed in the past year that my brakes feel softer than most cars I drive, but I figure.. they are new cars, and my car is pretty old.
In the past 2-3 months I have notices a pulsing in my brakes...it sounds/feels kinda like the ABS, but I was thinking it would be worth getting my brakes inspected soon.
Then this past week, I totally blew a brake line when I was driving.
The car has about 140,000 miles on it and the mechanic says a brake line alone may not be related to the pulsing sounds...because brake lines usually go because of rust....
So...thoughts on things I should be looking at? What could the pulsing be a symptom of?
if one brake line blew, and it is rust, is the other one not far behind? (this was a new england car up until 2 years ago)
Ford 7.3L Power Stroke (1999-2003) :: Brakes Sometimes Soft Other Times Firm
So the other day I had someone change lanes and slam on the binders right in front of me which caused me to slam on mine. Luckily no one got hit. Now my brakes feel different. Sometimes the pedal feels nice a firm other times it pushes in 2-3" before starting to brake. The fluid level has not changed in the resevoir and the hydroboost appears to be working fine. The power steering is still operating as before. I have checked the calipers and none are leaking.
My suspect is the master cylinder but was wondering if the symptoms are common with the master cylinder failing? I'm thinking internal o-ring has failed due to the near accident event. I'm going to do power steering flush just because I never have. Is there anything that would display these symptoms that I could check before buying the master cylinder?