IS F (2008-2014) :: Wheel Hubs Went Rusty
A Water gets into wheel hubs much easier with aftermarket wheels than OEM wheels. I have a set of BBS RS-GT wheels and this is what the rear hub looks like after about a year. Previously I noticed with OEM wheels there is just a little surface rust. Hopefully I won't need to remove in the future as it looks welded.
View 14 RepliesFord F-150 (2004-2008) :: 4 Wheel Drive Is Not Working / Front Hubs Won't Lock In
(2004 f150 S.Crew 4x4) I noticed that my 4 wheel drive is not working. The front hubs won't lock in. The transfer case will go into 4 low but the hubs still won't lock in.
Anyway, I have pulled vacuum on both actuators and one of them won't hold. It's obviously bad, but is that why I don't have 4x4? It seems to me like it is not...
When I pull a vacuum on the actuator that does hold, it disengages the hub from the driveshaft allowing free-wheeling. Correct me if I'm wrong, but when the truck is running in 2wd, vacuum must flow to the actuators preventing the hubs from engaging? The actuator on the bad side is locked 'in' so the driveshaft always turns.
According to my train of thought, since the actuator has failed in the 'locked in' position, I should still have 4x4- What am I missing?
Ford F-150 (2009-2014) :: Clicking Noise From Front Hubs
Front hubs are making a clicking noise pull in 4x4 and it quits also when pulling camper or boat quits make noise when you let off the gas could this be a vacuum line issue or automatic hub issue?
View 2 RepliesToyota - Previa :: All Wheel Drive Makes A Howling Noise From Front End
1993 Previa, all wheel drive makes a howling noise from the front end, all speeds, in or out of gear. Bearings have been checked for looseness and seem OK. Might it be the front trans axle or whatever mechanism they use up there? 220,000 miles.
View 3 RepliesPontiac - Sunfire :: 1997 - Left Front Wheel Makes A Thumping Noise
When driving in any direction, my left front wheel makes a thumping noise. it's not the tires, i have brand new ones. i can feel the thumping in my gas pedal, and if i were to let go of the steering wheel, the car moves to the left really hard. i have had people tell me wheel bearings, and i have had people tell me warped rotor.
View 3 RepliesElantra HD (2006-10) :: 2008 - Steering Wheel Makes A Binding Noise When Turning
I have a 2008 Elantra with 59,000 miles. When it is warm out (70 F+), the sterering wheel makes a binding noise (squeeking noise - it is hard to describe) when turning. It doesn't do this all the time and it is much more noticeable when it is warm out. The temps are usually mild. This is a recent problem as I haven't noticed it before.
Should I be concerned about this? I want to get it checked before the 60,000 mile mark in case this is a serious issue such as rack and pinion steering problems.
Golf IV R32 :: Front Driver Wheel Makes Loud Ticking Noise When Turn To Right Or Left
Recently I lowered my .:R pretty low on fk highsports.. well today i was backing off into my driveway.. When i turned my wheels to the right or to the the left the front driver wheel makes loud noise like tick tick tick.. when i put my wheels straight no noise at all.. It happens when i go forward or backwards turning my wheels to the right or left..
View 13 RepliesPassat (B7) :: Clunk Or Pop Noise From Left Front Wheel When Brakes Applied
I have started hearing a noise with my brakes. First thing in the morning when I back up and apply the brakes, I get a clunk or pop noise from the left front wheel. It will pop again once I move forward and hit the brakes. It only does the noise one time when I first apply the brakes in either direction. Once the brakes have been used out on the road and are warm, there is no noise when changing directions. I've had this noise in another car I used to have and it was caused by the aftermarket brake pads not being exactly large enough and there was slight pad shifting in the caliper. Being this is a new car and has the OEM pads, I would hope there would be no pad shifting or movement in the calipers.
View 17 RepliesFord F-150 (2004-2008) :: While Turning Makes Rubbing / Grinding Noise From Front?
I've got a new issue that is happening on the front end of my truck. Whenever I try turning my wheel while driving, I get this rubbing/grinding noise coming from the front of my truck. It only happens when the wheels are in motion. It seems to happen less when I'm driving at higher speeds, but I can notice it make the sound at any speed. I tried driving it slowly in an empty parking lot while turning and it's definitely making the sound every time the tires rotate.
I took it in for an alignment because this was happening every time I drove, whether it be driving straight or making a turn. Now that my alignment has been fixed, it no longer make this noise if I am driving in a straight line, so it only seems to happen when I'm turning. I had the mechanic check to see if they could reproduce the issue. The mechanic was able to hear what I hear, but when he put it on the lift at the shop, he was not able to reproduce the sound.
Camry 2012+ :: Pop / Clunk Noise Coming From Front Wheel After Coilover Install
So I was searching around online and it seems this thing happens to some ppl after lowering their cars. I'm getting a loud pop/clunk noise from the front left side only. Seems that's the most common place ppl are having this type of issue with. What it could be? My mechanic wont be able to look at it till Friday. So not sure on what to do. The sound only happens when I'm hitting bumps on the road.
View 6 RepliesIS F (2008-2014) :: Rattling Noise From Suspension / Clunk Or Slight Jerk When Shift Into First Gear
I recently got my 09 ISF and had a few questions pertaining to some noises I'm hearing. Of course I'm hearing the ticking from the motor but until it causes any issues I can live with it.. My real questions deal with
A: When I go over a bump such as a pot hole cover or something that makes my suspension articulate quickly at low speed, I hear a rattling noise from what seems like the suspension / hub. If it makes any difference in on 2012 shocks and soft springs. (my extended warranty is kicking in soon so I hope that it doesn't play a roll in it as I'm sure they will be quick to deny it)
B: When I am coming to a stop or slowing down and the car shifts into first on its own (I think only in manual mode) there is a clunk / slight jerk sometimes... It may be coming from the rear end? Is it some type of locking or unlocking that's going on?
IS F (2008-2014) :: 2011 - Clunk / Tapping Noise When Full Steering At Slow Speed
Just like the tittle says. My 2011 ISF with 56k miles on it is making a Clunking noise when pulling out of a parking spot or just anytime I fully steer to the left side and begin to move. If I try it in reverse it doesn't matter if I turn the steering wheel fully to left or right it makes the same noise as I begin to move at slow speed. It almost feels like something is pushing the front wheels out. During normal driving I don't feel anything at all, just as steady as solid the car can be.
Is there any common issues with ISF with premature wear of ball joints, cv joint, sway bar bushings or hub bearing?
Lexus IS 2014+ :: 2015 - Front Clunk Noise While Turning The Steering While Back In Fixed Position
When backing out of same parking spot, I always hear a clunk, clunk, clunk, noise in the front while turning the steering while back in the fixed position. I have heard this noise in the past but did not think any thing of it.
It's hard reproduce this noise, it seems to only be happening when backing out and turning the steering wheel. Car only has a little over one thousand miles.
IS F (2008-2014) :: Clucking Sounds From Front Wheel When Going Between 5 To 15mph
So.. Today coming back from work, I felt clucking sound from front wheel when going from 5-15mph. I even felt that when I had my left foot on the foot rest area. Its appeared during the driving from work to home and check whether if there is any rock or tree branch on tire or wheel but no...
So after 30mins later, went to gym and the the sound was completely gone.. Would it be because of bad wheel bearing or suspension or ball joint issue?
2012 ISF
Ford F-150 (2009-2014) :: 2010 4x4 Fails To Lock In Front Hubs
My 2010 f150 stx 4x4 fails to lock in the front hubs...
View 2 RepliesFord F-150 (2009-2014) :: Front Hubs Are Ratcheting - Vacuum Leak
2009 f150 4x4. My front hubs are ratcheting, I probably have a vacuum leak somewhere. Any trick to find it? I had to drive about 90 kilometers to get home, hope I didn't ruin anything. I don't have a vacuum pump, but I have a vacuum gauge.
View 1 RepliesFord F-150 (2004-2008) :: Roaring Noise Coming From Right Front While Turning - Front Wheel Bearings?
I gotta a roaring noise coming from my right front while turning. Planning on replacing just the wheel bearings tomorrow & not the whole hub assembly(2008 2wd). Is there a thread that lays out the steps and other parts I may need? I've seen alot different stories on the net on how to do it. Everthing from I can press new bearings to I have to do 4x4 hub conversion. Seems to be some confusion.
View 2 RepliesFord F-150 (2004-2008) :: Front Hubs Won't Engage
2004 fx4, transfer case engages, but front wheels won't engage. I assume the vacuum solenoid is stuck, any other thoughts?
View 1 RepliesFord 7.3L Power Stroke (1999-2003) :: Replacing Front Wheel Bearing Hubs?
I was getting a growl/grinding noise from my front hubs (driver's side I think) when I do a slight right turn like going around a curve, not turning around a corner. Just started happening the last week after returning from a 4th of July roadtrip. First thought was wheel bearings going out and started reading up on the forum here to see what was needed. Last night, I started getting a continuous growl when I was 5 miles from the house so just pulled up and parked it. I'm assuming (without pulling anything apart), it's the bearing assembly and I can get the Timken version at Autozone locally.
The problem is I generally do my heavy maintenance at our family shop in San Antonio but I live in Austin so will need to do this in my driveway. I have all the basic tools, just need to know how involved it is to do in a driveway instead of a shop. Thoughts?